ICRealtime ICIP D3000AVIR-M User manual

HD Network Dome Camera User’s Manual
Version 1.2.3

i
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please
note: Do not connect two power supplying sources to the device at the same time; it may result
in device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera
1
Quick Start Guide
1
Installation Accessories Bag
1
Installation Position Diagram
1
CD
1

iv
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
1.3.1 Performance...........................................................................................................2
2Structure ......................................................................................................................................5
2.1 Dimensions....................................................................................................................5
2.2 Port Description ............................................................................................................6
2.3 Listening.........................................................................................................................8
2.4 Bidirectional talk............................................................................................................9
2.4.1 Device-end to PC-end..........................................................................................9
2.4.2 PC-end to the Device-end....................................................................................9
2.5 Alarm Setup...................................................................................................................9
3Installation..................................................................................................................................12
3.1 Device Installation Introduction ................................................................................12
3.2 Device Installation Steps...........................................................................................12
3.2.1 General Installation.............................................................................................12
3.2.2 Manual Zoom Lens Focus Operation...............................................................15
3.2.3 Side Cable Exit....................................................................................................16
3.2.4 Cable Connection................................................................................................16
3.3 Micro SD Card Installation ........................................................................................17

v
4Quick Configuration Tool.........................................................................................................19
4.1 Overview......................................................................................................................19
4.2 Operation.....................................................................................................................19
5Web Operation..........................................................................................................................21
5.1 Network Connection...................................................................................................21
5.2 Login and Main Interface...........................................................................................21
6FAQ ............................................................................................................................................23
Appendix Toxic or Hazardous Materials or Elements ...............................................................24

1
1General Introduction
1.1 Overview
This series network camera combines traditional camera and network video technology into one unit
which integrates A/V data collection and transmission through network without aux devices. It uses
advanced H.264 and MJPEG video compression technology and G.711a audio compression technology,
which maximally guarantee the audio and video quality.
This series network camera enclosure has the strong resistance capacity, which can guarantee the
proper work performance under heavy strike. It supports real-time monitor and listening at the same time.
It supports analog video output and dual-way bidirectional talk.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the network
and then use a network client-end. Due to its multiple functions and various uses, this series network
camera is widely used in many environments such home, office, bank, road monitor and etc.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
You can edit each group at anytime.
Storage
Function
Support central server backup function in accordance with your configuration and
setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end PC.
Support built-in Micro SD card.
Support network storage like FTP, support short-time storage when encounter
disconnection.
Alarm
Function
Real-time respond to external local alarm input and video detect as user pre-
defined activation setup and exert corresponding message in screen and audio
prompt(allow user to pre-record audio file)
Real-time video detect: motion detect, tampering.
Can generate an alarm when network abnormal, Micro SD card abnormal event
occurred.
Network
Monitor
Network camera supports one-channel audio/video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
Max supports 20 connections.
Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
Support web access, widely used in WAN.
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Support various network protocols.
Peripheral
Equipment
Support the on-off alarm device to alarm via the sound or the light.
Power
External power adapter DC12V/AC 24V (Only vandal proof series support AC
24V)
Support PoE.
Warning！
Do not connect two power supplying sources to the device at the same time; it
may result in device damage!

2
Assistant
Function
Log function
Support PAL/NTSC
Day/Night mode auto switch (electromagnetic ICR switch).
Auto iris adjustment
Built-in IR light. Support IR night vision (For IR Series only).
Backlight compensation: screen auto split to realize backlight compensation to
adjust the bright.
Support electronic shutter and gain setup.
Support 3D NR.
Support video watermark function to avoid vicious video modification.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheets for network camera performance specification.
Model
Parameter
ICIP D3000AVIR-M
System
Main
Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network monitoring, local record, and remote operation.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Micro SD card status, bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3 inch CMOS
Pixel
2048(H)×1536(V)
Day/Night
Mode
Support day/night mode switch and electromagnetic IR-CUT at the same
time.
Auto Iris
DC drive
Gain Control
Manual/Auto
White Balance
Manual/Auto
BLC
On/Off
Electronic
Shutter
Manual/Auto
It ranges from 1/3 to 1/100000.
Video
Compression
Standard
H.264/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream (2048*1536@20fps)
extra stream 1(704*576@25fps)
extra stream 2(1280*720@1fps)
Main stream (1920*1080@25fps)
extra stream 1(704*576@25fps)
extra stream 2(1280*720@11fps)
NTSC:
Main stream(2048*1536@20fps)
extra stream 1(704*480@20fps)
extra stream 2(1280*720@1fps)
Main stream(1920*1080@20fps)

3
extra stream 1(704*480@30fps)
extra stream 2(1280*720@1fps)
Note:
Extra stream 2’s actual frame depends on device max capacity set which
can be adjusted within its range.
Video Bit Rate
H.264H: 40Kbps-8193Kbps. It is adjustable
MJPEG: 40Kbps-16384Kbps adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, tampering, overlay.
Lens
2.7mm～12[email protected]
Lens Interface
¢14. Lens is the default accessories.
Audio
Audio Input
1-channe RCA LINE IN (additional cable required)
Audio Output
1-channe RCA LINE OUT (additional cable required)
Bidirectional
Talk Input
Reuse the first audio input channel
Audio Bit Rate
8kbps 16bit or 16kbps 16bit
Audio
Compression
Standard
G.711a/G.711Mu
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold 0-100.
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Privacy Mask
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Alarm Input
1-channel input，1-channel output
Record and Backup
Record
Priority
Manual>External alarm >Video detect>Schedule
Storage
Management
Support Micro SD card (64G) storage, NAS storage
Network
Wired Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network
Protocol
HTTP,TCP,ARP,RTSP,RTP,UDP,RTCP,SMTP,FTP,DHCP,DNS,DDNS,PP
PoE,IPv4/v6,SNMP,QoS,UPnP,NTP, QoS, 802.1x.
Remote
Operation
Monitor, system setup, log information, maintenance , upgrade and etc
Protocol
PSIA, ONVIF
AUX
Interface
Video Output
1-ch analog output, BNC port (need additional cable)
Reset
Built-in RESET button
IR light
IR distance 20~30 meters (For IR series product only)
General
Parameter
Power
Support AC24V, DC12V and PoE (AC 24V port is inside the device.)
Power
Consumption
General series: below 5W.
IR series: below 7W.
Working
Temperature
-20℃～+60℃
Working
Humidify
≤95%

4
Dimensions(m
m)
¢151×119
Weight
1.25 kg
Installation
Support various installation modes

5
2Structure
2.1 Dimensions
You can refer to the following figures for dimension information. The Unit is mm. See Figure 2- 1(vandal-
proof series), Figure 2- 2 (vandal-proof series), Figure 2- 3 (non vandal-proof series) and Figure 2- 4
(non vandal-proof series).
Figure 2- 1 Dimension illustration 1
Figure 2- 2 Dimension illustration 2

6
Figure 2- 3 Dimension illustration 3
Figure 2- 4 Dimension illustration 4
2.2 Port Description
The port is shown as in Figure 2- 5 and Figure 2- 6.

7
Figure 2- 5 Port 1
Figure 2- 6 Port 2
Please refer to the following sheet for external connection port definition information.
SN
Port
Port Name
Connector
Function Description
1
POWER
AC 24V power
port
/
Connect to AC 24V power.
Please note some series need
additional wiring.
2
POWER
DC 12V power
port
/
Connect to DC 12V power.
3
LAN
RJ45 network
port
Ethernet port
Network cable port.
4
I/O
I/O port
/
It includes alarm input/output, audio
and analog output.
5
RESET
Reset button
/
Reset button. It is to restore factory
default setup.

8
6
Micro SD
Micro SD card
slot entry
Micro SD
card
Connect to Micro SD card to realize
local storage.
7
Fan port
/
/
Connect to fan to reduce device
internal problem.
Please note only some series
support this function.
8
Status
indicator
light
/
/
Display device status
Please refer to the following sheet for I/O port cable function information.
Port
Name
Cable SN
Cable Port Name
Function Description
I/O Port
1
ALARM_NO
Alarm output port. Output alarm signal to
alarm device.
NO: Normal open alarm output end.
2
ALARM_COM
Alarm output public end.
3
GND
Ground end.
4
ALARM_IN
Alarm input port. It is to receive the on-off
signal from the external alarm source.
5
GND
Ground end.
6
AUDIO_IN/AUDIO_IN
1
Input audio signal. It is to receive the analog
audio signal from the devices such as
pickup.
7
AUDIO_OUT
(optional)
This port may have either of the following
function, depending on model of the device:
Output audio signal to devices such as
loud speaker.
Input audio signal. It is to receive the
analog audio signal from the devices
such as pickup.
AUDIO_IN 2 (optional)
8
GND
Ground end.
9
VIDEO_OUT
Output analog video signal. It can connect
to TV monitor to view video.
Note:
The external connection port above is based on non-IR series which is identical with the external
connection port of IR series.
2.3 Listening
Note:
Some products support listening function only.
Device Connection
Firstly connect the pickup to the audio input port of device, and then connect earphone to the audio
output port of PC. Log in WEB page of the device, click on either one of or both to enable
listening function. When listening function is enabled, the button will become orange. You may click on
the button again to disable listening function.
Listening Operation

9
At the device end, speak via the pickup, and then you can get the audio from the earphone or sound box
at the pc-end.
2.4 Bidirectional talk
2.4.1 Device-end to PC-end
Device Connection
Please connect the speaker to the audio input port of the device. Then connect the earphone to the
audio output port of the PC.
Login the Web and then click the Talk button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the bidirectional talk function.
Click Talk button again to stop the bidirectional talk function.
Listening Operation
At the device end, speak via the pickup, and then you can get the audio from the earphone or sound box
at the pc-end.
2.4.2 PC-end to the Device-end
Device Connection
Connect the speaker to the audio input port of the PC and then connect the earphone to the audio
output port of the device.
Login the Web and then click the Talk button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Talk button again to stop the bidirectional talk function.
Please note the on-site listening operation is null during the bidirectional talk process.
Listening Operation
At the PC-end, speak via the pickup, and then you can get the audio from the earphone or sound box at
the device-end.
2.5 Alarm Setup
The alarm interface is shown as in Figure 2- 7. Please follow the steps listed below for local alarm input
and output connection.
1) Connect the alarm input device to the alarm input port (No.4 pin) of the I/O cable.
2) Connect the alarm output device to the alarm output port (No.1 pin) and alarm output public port (No.2
pin). The alarm output port supports NO (normal open) alarm device only.
3) Open the Web, go to the Figure 2- 7. Please set the alarm input 01 port for the first channel of the I/O
cable (No.4 pin). Then you can select the corresponding type (NO/NC.)
4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is the
No.1 pin of the I/O cable.

10
Figure 2- 7 Alarm
Please refer to the following figure for alarm input information. See Figure 2- 8.
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of the
alarm input port. When the input signal is connected to the 3.3V or is idle, the device collects the logic
“1”. When the input signal is grounded, the device collects the logic “0”.
Figure 2- 8 Alarm input
Please refer to the following figure for alarm output information. See Figure 2- 9.
Port ALARM_C and Port ALARM_NO composes an on-off button to provide the alarm output.
If the type is NO, this button is normal open. The button becomes off when there is an alarm output.
Figure 2- 9 Alarm output

11

12
3Installation
Important
Before you complete the installation and setup, do not remove the electrostatic attraction
film on the transparent enclosure. Otherwise it may result in injury.
After remove electrostatic attraction film, do not touch dome enclosure in case it may leave
stain.
Before the installation, please make sure the installation surface can sustain at least 3X
weight of the bracket and the camera.
3.1 Device Installation Introduction
Please refer to Figure 3- 1 (vandal-proof series) and Figure 3- 2 (non vandal-proof series) for device
installation space information. You can see there are installation position diagram and installation screws
in the accessories bag for you to install the device conveniently.
Figure 3- 1 Device installation 1
Figure 3- 2 Device installation 2
3.2 Device Installation Steps
3.2.1 General Installation
The general interface is shown as in Figure 3- 3.

13
Figure 3- 3 General installation 1
Step 1
Take the installation position diagram from the accessories bag and then paste it on the installation
ceiling or the wall according to the monitor area. Please dig three bottom holes of the plastic expansion
bolts according to the diagram. Take three expansion bolts from the accessories bag and then insert
them to the holes you just dug and then fix firmly. If you need to dig a hole to pull through the cable, you
need to dig a cable exit hole on the installation surface according to the installation positioning diagram.
Step 2
Remove the dome camera enclosure according to the following steps.
a) For vandal-proof series, use the inner hex wrench from the accessories bag to unfasten the 3 hex
screws on the dome camera enclosure and then remove it
b) For non vandal-proof series, rotate the dome camera enclosure counterclockwise as in Figure 3- 4
until you can remove it.
Figure 3- 4 General installation 2

14
Step 3
Adjust the device chassis and pull the cable through the exit hole. Make fixture hole on chassis face the
three plastic expansion bolts (in Step 1). Take 3 ST3.0 self-tapping screw out from the accessories bag
and fix them on the three plastic expansion bolts to secure the chassis on installation surface.
Note:
Make host GND grounded which can improve device reliability. For outside installation, the host
GND must be grounded.
GND of vandal-proof series locates next to its exit hole. GND of non vandal-proof series locates at
rear of the camera.
Device grounding screw dimension is M3X0.5 with valid depth 5mm.
Step 4
Adjust angle of the lens according to actual need.
a) For the IR series product, you can skip current step and go the step b) directly. For the non-IR
series product, push the port slightly to remove the decoration enclosure from the black plastic
enclosure. See Figure 3- 5.
Figure 3- 5 General installation 3
b) Lens pan rotation angle setup. Please refer to Figure 3- 6 to unfasten the lock screw A and adjust
the pan monitor angle to the proper position. Then fix the lock screw A. The pan angle ranges from
0°~350°.
c) Lens tilt rotation angle. Please refer to Figure 3- 6 to unfasten the lock screw B and lock screw C
and adjust the tilt monitor angle to the proper position. Then fix the lock screw B and lock screw C.
The tilt angle ranges from -20°~+70°.
d). Image pan rotation angle setup. Please refer to Figure 3- 6 to turn lock screw D to adjust the video
pan angle. Then fix the lock screw B and C. The video pan angle ranges from 0°~+350°.