iDataLink maestro Rr User manual
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in
are the properties of their respective owners.
WARNING
Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced
options in the Print menu.
Install your Maestro RR according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE
1
2
3
SELECT VEHICLE
PRINT PAGES NEEDED
ELECTRONICS
Click here for:
Radar Installation Guides
2008-2014
Ford EconolinE
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro FO1 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OR
OPTIONAL ACCESSORIES
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2
Ford EconolinE 2008-2014
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
Troubleshooting Table 6
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3
Ford EconolinE 2008-2014
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness
and match the wire colors.
• Connect every wire from the aftermarket radio main
harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
Vehicles equipped with navigation radios skip to Step 3.
(Required for vehicles equipped with SYNC, without factory
navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the
factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test
probe to the wire SWI 2 wire. Have the ignition and the
radio ON. If the SWI 2 wire is connected, the multimeter
will display approximately 5 volts. This value will drop upon
pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire
side going to the SYNC module and plug the SYNC harness
into the SYNC module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect
only the available connectors. For example, if the factory
harness has two connectors, connect only these two
connectors.
STEP 4
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket
radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio
jack of the aftermarket radio (if there is no iDatalink audio
input, connect to AUX).
Note: On Pioneer radio, ensure that there is nothing
plugged into the W/R port.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed
the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to
feed the center channel of the THX system or as a second
subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to
connect the factory 3.5 mm audio jack, in vehicles that
are NOT equipped with SYNC, to the auxiliary input of the
aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4
Ford EconolinE 2008-2014
AUX INAUX IN
SUB IN
CENTER IN
SUB IN
CENTER IN
1
OBDII CONNECTOR
STEP 4
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BROWN (NOT CONNECTED)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEED
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
DATA
CABLE
PURPLE - RR SPEAKER (+)
CONNECT TO
AFTERMARKET RADIO
RCA CABLES
WIRING DIAGRAM
STEP 1 STEP 5
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
MAESTRO RR MODULE
DATA
CABLE
FACTORY RADIO HARNESS
SYNC HARNESS
PINK/RED - SWI 2 (-) INPUT INSULATE
WIRE
SYNC
MODULE SIDE
STEERING
WHEEL SIDE
STEP 2
STEP 3
STEP 6
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEERING WHEEL
CONTROL CABLE
NOT REQUIRED
PIONEER RADIO: ENSURE THAT NOTHING
IS PLUGGED IN W/R PORT.
CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC
AUDIO
CABLE
SWI 2 : BLUE/ORANGE
CENTER DASH, UNDER THE RADIO
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5
Ford EconolinE 2008-2014
RADIO WIRE REFERENCE CHART
Wire
Description Polarity Wire Color on Maestro
T-Harness
Wire Color on Alpine
cable
Wire Color on Kenwood
cable
Wire Color on Pioneer
cable
Wire Color on Sony
cable
Illumination (+) Orange N/A Orange/White Orange/White Orange
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6
Ford EconolinE 2008-2014
TROUBLESHOOTING TABLE
PROBLEM SOLUTION
Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the
vehicle.
If you hardwired connections at the OBDII, check connections at the OBDII
connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/
BROWN wire is connected to PIN 14 of the OBDII connector. Do not use
T-Taps. Soldering or military splicing methods are recommended.
Reset the RR.
There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the
RR and the radio. Make sure it is in the correct radio input.
The radio will not turn on, and there was no 16-pin plug connected to the
OEM radio.
The data lines are not present behind the radio and must be connected at the
OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from
the FO1’s 16-pin plug to:
BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/
ORANGE) at the OBDII.
The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module.
The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and
that it is plugged into the black port on the Maestro RR. The red and blue
ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during
the flash. Verify the radio’s serial number entered during the flash matches
what is listed on the radio screen. This can be found in the settings of the
radio, listed as Device Id, Device Number, or Serial Number.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: maestr[email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
ELECTRONICS
Click here for:
Radar Installation Guides
2007-2010
Ford EdgE
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro FO1 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OR
OPTIONAL ACCESSORIES
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2
Ford EdgE 2007-2010
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
Troubleshooting Table 6
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3
Ford EdgE 2007-2010
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness
and match the wire colors.
• Connect every wire from the aftermarket radio main
harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
Vehicles equipped with navigation radios skip to Step 3.
(Required for vehicles equipped with SYNC, without factory
navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the
factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test
probe to the wire SWI 2 wire. Have the ignition and the
radio ON. If the SWI 2 wire is connected, the multimeter
will display approximately 5 volts. This value will drop upon
pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire
side going to the SYNC module and plug the SYNC harness
into the SYNC module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect
only the available connectors. For example, if the factory
harness has two connectors, connect only these two
connectors.
STEP 4
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket
radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio
jack of the aftermarket radio (if there is no iDatalink audio
input, connect to AUX).
Note: On Pioneer radio, ensure that there is nothing
plugged into the W/R port.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed
the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to
feed the center channel of the THX system or as a second
subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to
connect the factory 3.5 mm audio jack, in vehicles that
are NOT equipped with SYNC, to the auxiliary input of the
aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4
Ford EdgE 2007-2010
AUX INAUX IN
SUB IN
CENTER IN
SUB IN
CENTER IN
1
OBDII CONNECTOR
STEP 4
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BROWN (NOT CONNECTED)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEED
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
DATA
CABLE
PURPLE - RR SPEAKER (+)
CONNECT TO
AFTERMARKET RADIO
RCA CABLES
WIRING DIAGRAM
STEP 1 STEP 5
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
MAESTRO RR MODULE
DATA
CABLE
FACTORY RADIO HARNESS
SYNC HARNESS
PINK/RED - SWI 2 (-) INPUT INSULATE
WIRE
SYNC
MODULE SIDE
STEERING
WHEEL SIDE
STEP 2
STEP 3
STEP 6
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEERING WHEEL
CONTROL CABLE
NOT REQUIRED
PIONEER RADIO: ENSURE THAT NOTHING
IS PLUGGED IN W/R PORT.
CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC
AUDIO
CABLE
SWI 2 : BLUE/ORANGE
CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5
Ford EdgE 2007-2010
RADIO WIRE REFERENCE CHART
Wire
Description Polarity Wire Color on Maestro
T-Harness
Wire Color on Alpine
cable
Wire Color on Kenwood
cable
Wire Color on Pioneer
cable
Wire Color on Sony
cable
Illumination (+) Orange N/A Orange/White Orange/White Orange
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6
Ford EdgE 2007-2010
TROUBLESHOOTING TABLE
PROBLEM SOLUTION
Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the
vehicle.
If you hardwired connections at the OBDII, check connections at the OBDII
connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/
BROWN wire is connected to PIN 14 of the OBDII connector. Do not use
T-Taps. Soldering or military splicing methods are recommended.
Reset the RR.
There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the
RR and the radio. Make sure it is in the correct radio input.
The radio will not turn on, and there was no 16-pin plug connected to the
OEM radio.
The data lines are not present behind the radio and must be connected at the
OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from
the FO1’s 16-pin plug to:
BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/
ORANGE) at the OBDII.
The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module.
The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and
that it is plugged into the black port on the Maestro RR. The red and blue
ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during
the flash. Verify the radio’s serial number entered during the flash matches
what is listed on the radio screen. This can be found in the settings of the
radio, listed as Device Id, Device Number, or Serial Number.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: maestr[email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
ELECTRONICS
Click here for:
Radar Installation Guides
2008-2012
Ford EscapE
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro FO1 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OR
OPTIONAL ACCESSORIES
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2
Ford EscapE 2008-2012
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
Troubleshooting Table 6
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3
Ford EscapE 2008-2012
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips.
Connect every wire to the aftermarket radio main harness
and match the wire colors.
• Connect every wire from the aftermarket radio main
harness to the FO1 T-harness and match the wire colors.
(Refer to Diagram)
STEP 2
Vehicles equipped with navigation radios skip to Step 3.
(Required for vehicles equipped with SYNC, without factory
navigation system; refer to Vehicle Wire Chart)
• Disassemble the dashboard carefully and remove the
factory radio from its housing without disconnecting it.
• See the WIRE CHART for vehicle wire color and location.
• Use a multimeter to test the SWI 2 wire. Connect the
BLACK test probe to ground (-) and connect the RED test
probe to the wire SWI 2 wire. Have the ignition and the
radio ON. If the SWI 2 wire is connected, the multimeter
will display approximately 5 volts. This value will drop upon
pressing the steering wheel voice, phone or OK button.
• Cut the SWI 2 INPUT wire.
• Connect the PINK/RED wire of FO1 T-harness to the SWI 2
INPUT wire going to the steering wheel. Insulate the wire
side going to the SYNC module and plug the SYNC harness
into the SYNC module.
STEP 3
• Connect the factory harness to the FO1 T-harness. Connect
only the available connectors. For example, if the factory
harness has two connectors, connect only these two
connectors.
STEP 4
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket
radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio
jack of the aftermarket radio (if there is no iDatalink audio
input, connect to AUX).
Note: On Pioneer radio, ensure that there is nothing
plugged into the W/R port.
• Insert the RCA connectors into the aftermarket radio.
NOTES:
The RCA connectors labeled SUB IN can be used to feed
the subwoofer channel of the factory amplifier.
The RCA connector labeled CENTER IN can be used to
feed the center channel of the THX system or as a second
subwoofer channel (if applicable).
The RCA connectors labeled AUX IN can be used to
connect the factory 3.5 mm audio jack, in vehicles that
are NOT equipped with SYNC, to the auxiliary input of the
aftermarket radio.
STEP 6
• Secure the aftermarket radio in the dashboardhousing.
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4
Ford EscapE 2008-2012
AUX INAUX IN
SUB IN
CENTER IN
SUB IN
CENTER IN
1
OBDII CONNECTOR
STEP 4
CONNECT AUX IN
ONLY IF YOU DON’T HAVE SYNC
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BROWN (NOT CONNECTED)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEED
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
DATA
CABLE
PURPLE - RR SPEAKER (+)
CONNECT TO
AFTERMARKET RADIO
RCA CABLES
WIRING DIAGRAM
STEP 1 STEP 5
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
MAESTRO RR MODULE
DATA
CABLE
FACTORY RADIO HARNESS
SYNC HARNESS
PINK/RED - SWI 2 (-) INPUT INSULATE
WIRE
SYNC
MODULE SIDE
STEERING
WHEEL SIDE
STEP 2
STEP 3
STEP 6
WIRES FROM
VEHICLE
FO1 T-HARNESS
STEERING WHEEL
CONTROL CABLE
NOT REQUIRED
PIONEER RADIO: ENSURE THAT NOTHING
IS PLUGGED IN W/R PORT.
CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC
AUDIO
CABLE
SWI 2 : BLUE/ORANGE
JUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5
Ford EscapE 2008-2012
RADIO WIRE REFERENCE CHART
Wire
Description Polarity Wire Color on Maestro
T-Harness
Wire Color on Alpine
cable
Wire Color on Kenwood
cable
Wire Color on Pioneer
cable
Wire Color on Sony
cable
Illumination (+) Orange N/A Orange/White Orange/White Orange
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A
ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6
Ford EscapE 2008-2012
TROUBLESHOOTING TABLE
PROBLEM SOLUTION
Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the
vehicle.
If you hardwired connections at the OBDII, check connections at the OBDII
connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/
BROWN wire is connected to PIN 14 of the OBDII connector. Do not use
T-Taps. Soldering or military splicing methods are recommended.
Reset the RR.
There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the
RR and the radio. Make sure it is in the correct radio input.
The radio will not turn on, and there was no 16-pin plug connected to the
OEM radio.
The data lines are not present behind the radio and must be connected at the
OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from
the FO1’s 16-pin plug to:
BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/
ORANGE) at the OBDII.
The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module.
The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and
that it is plugged into the black port on the Maestro RR. The red and blue
ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during
the flash. Verify the radio’s serial number entered during the flash matches
what is listed on the radio screen. This can be found in the settings of the
radio, listed as Device Id, Device Number, or Serial Number.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: maestr[email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
ELECTRONICS
Click here for:
Radar Installation Guides
2007-2014
Ford ExpEdition
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro FO1 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OR
OPTIONAL ACCESSORIES
Other manuals for maestro Rr
48
Other iDataLink Adapter manuals
