IDAW Freestanding cabinet User manual

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
Assembly instructions: Freestanding cabinet
Please take the time to read the instructions. Please do not just proceed by looking at the
pictures alone! It is noticeable to you when you set it up. Thank you 
For safety and practical reasons, please note the following:
To avoid damage to the material and accidents, the cabinet should be assembled by two
people.
An important piece of information about the custom-made cabinet with depths of less than
44 cm.
Usually, our closet does not need to be wall-mounted as it is quite heavy and stable.
In certain cases, instead, due to the reduction in depth and high height, it is mandatory to
mount them on the wall. The person who performed the installation must attach it to the
wall before installing the door to avoid the risk of falling forward.
Please open the packages in the order listed. This will help you to avoid assembly
difficulties!
When opening the package of metal parts, small parts and fittings, please ensure that no
part is lost, since the parts are counted exactly and are only available in the number
required for assembly.
If you also ordered LED lights, please note the following before setting up:
The horizontal sensor LED bar with motion detector (see video) is mounted under the
wardrobe cover at the top (inside the cabinet). Use the two supplied screws for this.
The vertical LED bar, in the dividing side panel (see video), is installed in the inner cheek in
which the milling is provided for this at the factory. In our video you can see how to
assembly it with the wardrobe dividing side panel hole already prepared; however, it is
much easier to install on a cupboard dividing side lying on the floor or on the table. Be sure
to start at the top, 2.5 cm below the end of the dividing side panel, on which the cupboard
top cover will be attached later, when you insert the vertical LED bar in the horizontal
wardrobe dividing side panel. Since the same LED lengths are used for different cupboard
heights, it can happen that a small part of the lower, vertical LED bar is covered by the
wardrobe base.
Horizontal LED strips: For the power cable, a hole should be drilled into the wardrobe top

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
cover on the left outside the position where the LED bar is to be screwed on, so that the
power cable can be routed above and behind the wardrobe to a socket.
Please note that there must be some space available for the transformer of the LED
systems! The easiest way to accommodate the narrow transformer is behind the dividing
side panel if there is at least 3 cm of space between one of the wardrobe dividing side panel
and wall behind the side cover panel (when you have ordered fitted wardrobe).
Alternatively, it can be placed behind the wardrobe back if the wardrobe can be set up
approx. 2 cm forward. The third variant for the free standing wardrobe as for fitted
wardrobe is to accommodate the transformer on the top of the cabinet cover: However, this
is only possible if, in addition to the necessary centimetre that is required for the
construction, there is about 2 cm more space up to the ceiling. The last option is to cut a
cutout for the transformer in the wardrobe back: This has the advantage that it is easily
accessible.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 1 – –
Unpack the outer side panel of the wardrobe the right (A) or left (A). Attention, these are
not identical!
First attach the leveling feet (see the photo) to the first left outer side panel only on the side
facing the inside of the wardrobe (i.e. on the right side). Mount the leveling feet as shown in
the drawing (right side).

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
IMPORTANT: Glue ordinary furniture felts (not included) to the bottom of the leveling feet
to avoid the wardrobe from scratching the floor when it is moved.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
Screw the four pins (see photo below) into the indicated holes. First screw the pins all the
way in and then turn them back a little until the two holes are positioned vertically (see the
photo with the arrows below). Please proceed precisely to ensure that they can be
connected easily later.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 2 – –
Unpack the base (F) and the top cover (E). Check whether the base and cover are correct
for the respective module by comparing the dimensions with the drawing on the first page.
Use a screwdriver to open the milled groove, into which the back side of the wardrobe will
later be inserted, up to the edge (see drawing below). For this, the milled groove on the
edge must be opened. That is why this enables the back side of the wardrobe to be inserted
laterally. Carry out this step both in the base and the top cover.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 3 – –
Insert the metal components into the holes shown below. Pay attention to the correct
positioning so that the pins can be inserted later (in the base and top cover of the
wardrobe).

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 4 – –
Put in the base and the left outer side panel together and tighten the screw shown below.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 5 – –
Unpack the back side of the wardrobe (C) and select the right one with the appropriate
width for the respective module (the back side of the wardrobe is approx.1.5 cm wider than
the module, as it is inserted into the milled groove in the cabinet side panels, base and top
cover).

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 6 – –
Be careful with the next step! Please do it in two in any case!
Put on the top cover element with the help of a ladder. Insert the back side of the
wardrobe and the top cover into the milled groove and then slide the top cover to the left up
to the left side of the cupboard until the pins enter the holes. Now insert and tighten the
screws. Attention: If the cover cannot be pushed in, check whether both the holes and the
pins are correctly positioned as described above. If necessary first remove the cover and
correct the position of the holes and pins. See also our montage film.
– – 7 – –
Now unpack the side dividing panel of the wardrobe, assemble the two cupboard feet
(don’t forget the furniture felts) and screw in the pins on both sides. Pay attention to the
correct position of the pins and the holes.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
Proceed in the same way with all wardrobe side dividing panels up to the last right outer
side panel on the right-hand side of the wardrobe, where pins and leveling feet are mounted
on the left-hand side (towards the inside of the cupboard).

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 8 – –
Now unpack the first door in the appropriate width. The width is noted on the label on the
box. In the modules with two doors, the left door has a plastic dust protection. First
assemble only one door (with two people) by screwing the hinges on the wardrobe to the
dividing side panel.
If the height of the wardrobe ordered differs from a standard size, pre-drilled holes for
mounting the hinges on the dividing side panel of the wardrobe may be missing.
Position the door exactly. Now fix the hinges, which find their place on pre-drilled holes, by
screwing in the vertical screws.
Now take care of the hinges for which there is no pre-drilled hole: Unscrew not much the
vertical screws of the door hinges. Please be careful not to unscrew them completely! With
firm pressure and horizontally, just screw these screws into the dividing side panel.
The door is correctly installed if there is 1.6 cm of space between the floor and the door!
– – 9 – –
Assemble all accessories firstly (when one door of the wardrobe is already assembly). Make
sure that the drawers and the shelves are not installed where are the hinges of the doors
(unless it is a cabinet with only one door) are attached. To determine the position of the
hinges, one of the doors was already installed.
– – 10 – –
If you have ordered a drawer element, the instructions follow here. If not, please continue
on with point 11!
The drawer module for installation inside the wardrobe is almost completely assembled.
Only a few steps are required (see photos below).
If you want to assembly the feet, which is not absolutely necessary, turn the module over
and carefully turn it upside down (this step was not shown in the photos) to assembly them.
Then put the feet on and turn the module over again. Then position the element inside the
wardrobe: either place the drawer module on the cupboard floor or mount it at a higher
point: To place it further up, place it on a shelf.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
The drawer boxes have a slightly lower depth than the shelves and can be set up flush at the
front.
After the drawer element has been positioned in the cabinet, first place the closing strips
on the left and right on the wooden pins provided and tap them into place (Attention: in the
photos, the strips were installed outside the wardrobe, which you should do better rather
than inside the wardrobe).
The drawer module is not attached separately, but is stable due to its weight and usually
standing behind the door hinges.
The enclosed wooden dowels are only used if you install two drawer modules one above the
other. A shelf serves as the cover shelf and support for the drawer box: it is either attached
like the other shelves. This leaves a small gap between the cover shelf and the top drawer.
The shelf can also just be put on if you prefer.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 11 – –
The shelves are mounted with the screws shown in the photo. The shelf clicks into place and
is thus firmly stabilized.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 12 – –
Fasten each clothes rail holder to the side panel with two screws on the side. Important:
Mount the clothes rail either under a shelf or under the top cover of the wardrobe and as
centrally as possible in the wardrobe depth.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
– – 13 – –
Use the Hex (Allen) key (included) and a spirit level to position the wardrobe horizontally.
The leveling feet create a leveling of up to 5 mm.
– – 14 – –
Now you can assemble all doors.
– – 15 – –
If necessary, assembly the handles (the handles are already milled in the “integrated” door
variant). Attention: Mount the handle precisely and straight! Drill slowly outwards on the
pre-holes with a 3 mm wood drill and little pressure. A second person should check that the
drilling is being carried out perfectly in horizontally to the door.

IDAW srl uninominale (Einpersonengesellschaft)
capitale sociale (Grundkapital) i.v. 10000 euro - registro delle imprese P.I. (UST. IdNr.:) 05173760280, CF 05173760280
Via Roma 8/I, 35010, Vigonza, Provinz Padua, Italien
www.idaw.eu - [email protected]
Then drill from the outside in using a 5 mm drill bit and enlarge the hole. Then mount the
handle with the supplied screws. Do not tighten the screws immediately one after the other,
but screw them in step by step, i.e. alternately, at the same time.
– – 16 – –
Adjusting the doors.
Loosen screws A slightly to raise or lower the respective door. Then tighten the screws
again.
Turn screws B in or out to move the door left or right.
Loosen screw C slightly to increase or decrease the distance between the door and the
wardrobe module. Then tighten the screw again.
– – 17 – –