Idealight 7R BEAM A User manual

Order Code: 7R BEAM A
User Manual
All the products' information accord to the actual lightings' collocation. We will not
inform else if an change. We reserve the final interpretation right.
www.idealight.com.cn
Professional Moving Head Beam
Do your ideal light! What idea you have, what light we have!
www.idealight.com.cn

Professional Moving Head Beam Troubleshooting
3.1 Control Panel
3.2 DMX Control
Professional Moving Head Beam Fi ture Cleaning
4. Troubleshooting
5. Fixture Cleaning
● Clean with soft cloth using normal glass cleaning fluid.
●Alwa s dr the parts carefull .
5
The cleaning of internal and external optical lenses and/or mirrors must be carried
out periodicall to optimize light output. Cleaning frequenc depends on the
environment in which the fixture operates: damp, smok or particularl dirt
surrounding can cause greater accumulation of dirt on the unit’s optics.
●Clean the external optics at least ever 20 da s. Clean the internal optics at
least ever 30/60 da s.
Contents
1. Safet Instruction
Following are a few common problems that may occur during operation.
Here are some suggestions for easy troubleshooting:
A. The unit does no work, no light
1. Check the connect power and mains fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. Check DMX connectors, cables to see if the are linked properl .
2. Check the address settings and DMX polarit .
3. If ou have intermittent DMX signal problems, check the pins on the connectors
or on PCB of the unit or the previous one.
4. Tr to use another DMX controller.
5. Check to see if the DMX cable run near or run alongside to high voltage cables
that ma cause damage or interference to DMX interface circuit.
2. Technical Specfication
3. How to Control the Package
3.2.1 DMX 512 Configuration
3.2.2 DMX 512 Connection

Professional Moving Head Beam DMX 512 Connection Professional Moving Head Beam Safety
Safety Instructions:
Ever person involved with the installation, operation and maintenance should:
A001 A017 A033 A049 ● Be competent
A001 A021 A041 A061 ● Follow the instructions of this user manual
Make sure there are not flammable materials close to the unit while operating
Damages caused b user modifications to the unit are not subject to warrant .
4 1
Termination reduces signal errors and to avoid signal transmission problems and
interference. It is alwa s advisable to connect a DMX terminal.
(Resistance 120ohm 1/4W) between pin2(DMX-) and pin3(DMX+) of the last
fixture.
1.If ou use a controller with 5 pins DMX output, ou have to use a 5 to 3 pin adapter-
cable.
2.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in
the DMX-output of the last unit.
Please find the following examples to address our DMX512 channel for the
first 4 packages.
Caution
Take care using this equipment!
High voltage risk of electric shock.
Before our initial star-up, please make sure that there is no damage caused
during transportation. Should there be an , consult with the dealer and do not use
the unit.
16CH Mode:
20CH Mode:
Please keep this User Manual for future consultation. If ou sell the unit to
another user, be sure that the also receive this instruction booklet.
To maintain the equipment in good work condition and to ensure safe operation, it
is necessar for the user to follow the safet instructions and warning notes
written in the manual.
Warning
For your own safety, please read this user manual before operation.
Use universal DMX controller to control the packages, ou have to set the DMX
address from 1 to 512 channels so that the unit can receive the DMX signal. Caution
Before operating,make sure the voltage and frequence
of the power supply match the power requirements of the package.
When switch on the lighting, use the JOG WHEEL to choose the submenu DMX
512 Control to set the address. Once the address has been selected, press
ENTER button to store.

Professional Moving Head Beam Technical Specifations Professional Moving Head Beam Control Panel
You should find the following items inside the carton packing:
Main Functions:
Technical Specifations
Voltage: AC110-240V,50/60HZ
Lamp: OSRAM P-VIP 230W lamp
Power consumption: 350W
Lens: 3-lens HQ optical group (0°- 3.9°focus)
Pan: 540degree (16bit) Professional Moving Head Beam DMX 512 Configuration
Tilt: 270degree (16bit) 16CH/20CH
Color Wheel: 14 colors + open, with rainbow effect CH1 CH9
Gobo Wheel: 17 gobo (with gobo shaking/gobo flow)+ open CH2 CH10
Prism: 8-facet Rotating Prism CH3 CH11
Packing Size: 450*400*503mm CH4 CH12
Gross Weight: 20kg CH5 CH13
Operation Modes: ● DMX mode: 16CH/20CH ● Master/Slave mode ● Auto CH6 CH14
Professional Moving Head Beam Control Panel CH7 CH15
CH8 CH16
CH17
CH18
CH19
LCD display: Showing the menus and selected function CH20
Control Pannel / ENTER: When ou reset the lighting, please keep the Channel value at 255 for continuous 3s.
Mains input: Powercon in 0-127
DMX input / output: Use 3-pin XLR cable to link items together 128-200
Switch ON/OFF 201-255
2
3
Prism Rotation Pan/Tilt Movement
Dimmer Pan Fine
1pc Moving Head Beam, 1set OMEGA clamps, 1pc DMX cable,
1pc User Manual
Gobo Wheel
Tilt
DMX 512 Control (DMX Address Setting) -> Auto Run Mode -> Sound Run
Mode -> EDIT Mode -> SAVE SENCE -> SELECT CHANNEL (Channel
Mode) -> SELECT PAN (Pan reverse) -> SELECT TILT (Tilt reverse) ->
LANGUAGE -> S stem ke -> Adjust Restart (Set the value of Reset) ->
Start value (Recover to factor setting) -> S stem Reset
Attention: When you link a lot of pieces together, please make sure to set the same
channel mode (16CH or 20CH) for all of them in order to make sure their
synchronization.
｝
Pan/Tilt Speed
Gobo Wheel Speed
Color Wheel Speed
Focus Speed Optional
Frost
No Function
Prism Insertion Tilt Fine
Lamp
Reset
Strobe Pan
Color Wheel Focus
CH16
No Function
OFF
ON