Idis DC-D4211CRX User manual

DC-D4211CRX
Quick Guide

FCC Compliance Statement
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL
ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO
FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH
THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA
IS LIKELY TO CAUSE HARMFUL INTERFERENCE, IN WHICH CASE USERS WILL BE
REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.
WARNING : CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT. THIS CLASS OF DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT
REGULATIONS.
1

WEEE (Waste Electrical &
Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they
purchased this product, or their local government oce, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
2

IR LED Lens
Network Port Wall/Ceiling Installation Hole
Cable Access Hole Factory Reset Button
Body
1
3
2
4
5
6
Top Cover
Accessories
1. Network Camera
2. Quick Guide
3. Screws and Anchors (each 2ea)
4. Gimbal Screws (2ea)
5. Guide Pattern
3

Body
4
Camera Installation

5
1. Turn the top cover counterclockwise.
2. Use the screws, anchors provided with the camera to secure the
body on a wall or a ceiling.
*If xing the gimbal is necessary, use the gimbal screw(1) provided with the
product to x it.
• Check the wall or ceiling to see if it needs to be
reinforced. The camera may fall o if the wall or
ceiling is not strong enough to support its weight.
• Install the camera in a shaded area. If the camera
is installed in direct sunlight, it may be aected
adversely.

6
5. Adjust the angle.
3. Connect the network cable like the following picture.
4. Attach the top cover to the bottom cover. Turn the top cover
clockwise to fasten it.
*If the network cable comes out as shown below, use a nipper to cut out the cable
access hole in the top cover.

7
Dimension
59mm
30mm
86mm
26mm
3mm

Specications
Supported
Resolution
1920x1080, 1280x720, 640x360, 352x240
Image Sensor 1/2.8” CMOS
Lens 2.8mm Fixed-focal lens
Video
Compression
H.265, H.264 Main Prole, M-JPEG
Power Source PoE IEEE 802.3af (Class 2)
Power
Consumption
PoE IEEE 802.3af (Class 2) 3.6W
Covered by one or more claims of the patents listed at patentlist.accessadvance.com
V1.0 8

※ Please download software (IDIS Discovery, IDIS Center, IDIS Solution Suite
Compact) and product manual from this link :
- IDIS Website (www.idisglobal.com)
9

IDIS Co., Ltd.
For more information, please visit
www.idisglobal.com