IDTECK Star RFK101 User manual

Proximity Reader with KEYPAD
USER’S MANUAL
Proximity Reader with KEYPAD
Rev.3.5.1

Proximity Reader with KEYPAD
Table of Contents
1. Important Safety Instructions .............................................................................3
2. General..................................................................................................................3
3. Features ................................................................................................................4
4. Identifying Supplied Parts...................................................................................4
5. Specification.........................................................................................................4
6. Installation ............................................................................................................5
7. Wire Color Table of the Reader...........................................................................6
8. Wire Connection to Controller............................................................................7
9. Operation ..............................................................................................................8
10. Output Format ....................................................................................................9
11. Warranty and Service.......................................................................................13
12. RMA Request Form..........................................................................................14
2

Proximity Reader with KEYPAD
1. Important Safety Instructions
When using your Single Door Controller, basic safety precautions should always be followed to reduce
the risk of fire, electrical shock, and injury to persons. In addition, the following should also be
followed:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use mild
soap.
4. Do not use this product near water, such as bath-tub, wash bowl, kitchen sink, laundry tub, in a wet
basement, or swimming pool.
5. This product should be operated only from the type of power source indicated on the marking label. If
you are not sure of the type of power supplied to your installation site, consult your dealer or local
power company.
6. Never push objects of any kind into this product or through the cabinet slots as they may touch voltage
points or short out parts that could result in fire or electric shock. Never spill liquid of any kind on the
product.
7. To reduce the risk of electric shock, do not disassemble this product by yourself, but take it to qualified
service whenever service or repair is required. Opening or removing the covers may expose you to
dangerous voltages or other risks. Also, incorrect reassembly can cause electric shock when the unit is
subsequently used.
8. Unplug this product from the Direct Current (DC) power source and refer to qualified service personnel
under these conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled on the product.
c. If the product does not operate normally after following the operating instructions in this manual.
Adjust only those controls that are covered by the operating instructions in this manual. Improper
adjustment of other controls that are not covered by this manual may damage the unit and will
often require extensive work by a qualified technician to restore normal operation.
If the product exhibits a distinct change in performance.
2. General
The STAR RFK101 is an elegant looking and built in an attractive 10cm (4") read range proximity
reader with KEYPAD. The STAR RFK101 has back lighting on the KEYPAD that ensures you
successful operation even the night operating. The KEYPAD allows you to access door with proximity
card and personal PIN numbers.
Three LEDs of green, yellow and red, inside Piezo buzzer sound will guarantee you an accurate and
reliable system operations.
3

Proximity Reader with KEYPAD
3. Features
- Up to 4” (10cm) Read Range
- Built in 12 Key Numeric Keypad
- 26 Bit Wiegand, RS232, ABA Track || Magnetic Stripe
Format and 4/8 Bit Burst or 3*4 Matrix Output Available
-PSK Modulation
-User Format Available
-Back Lighting on Keypad
-3 LED Indicators
-Dual Beep Tones
-High Durability and Reliability
-Supervisory signal (optional)
4. Identifying Supplied Parts
Please unpack and check the contents of the box.
Reader unit Wall Mount O-ring User’s Manual
(1ea) (1ea) (5ea) (1ea)
5. Specification
Read Range/Time Up to 10cm (4") / 30ms
Input Voltage/Current DC 12V, 150mA
Reset Power on reset and WDT reset
LED/Beeper 3 LEDs (Red, Yellow and Green) / Piezo Buzzer
Keypad 12key back lighting
Color Dark Pearl Grey
Operating Environment -35℃~ +65℃, 10~90% Humidity
4

Proximity Reader with KEYPAD
Dimensions (WxHxD) 487mm(3.40")x100mm(3.94")x31mm(1.22")
Weight 190 g (0.412 lbs)
Output Format 26bit Wiegand, RS-232, ABA Track II Magstripe Output Format
with 8bit Burst or 3x4 Matrix Format for PIN
30.0mm
①② ③④
H:2.3mm
SOLDER:5mm
92.0mm
85.7mm
59.5mm
65.0mm
* Antenna Features
1. Antenna Type Loop Coil Antenna
2. Inductance Primary Coil: 13uH,
Secondary Coil: 627uH
3. Antenna Gain 34.54DB
4. Direction Omni-directional antenna
5.Polarization
Horizontal Polarization
6. Connection with Transmitter Soldering directly on PCB
6. Installation
6-1. Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical and one 1/2" hole at the center of these two
holes. (If you have installed electric gang box then skip this step.)
6-2. Using two 6-32 or M3 screws, install wall mount to the wall.
6-3. Insert 5 O-rings to the wall mount as indicated, then route the cable of the main unit through the
center hole and push the main unit to wall mount to lock the main unit and make sure that the main
unit is locked with wall mount.
5

Proximity Reader with KEYPAD
7. Wire Color Table of the Reader
POWER
Power(DC 12V) +12V Red wire
Power(DC 12V) 0V(GND) Black wire
OUTPUT
ABA Track II(Card Present) CLS Yellow wire
ABA Track II(Clock), Wiegand Data1 RD1 White wire
ABA Track II(Data), Wiegand Data0 RD0 Green wire
RS-232 TX TX Violet wire
KEYPAD 3x4 Matrix(Column0) C0 White wire with Blue stripe
KEYPAD 3x4 Matrix(Column1) C1 White wire with Green stripe
KEYPAD 3x4 Matrix(Column2) C2 White wire with Red stripe
KEYPAD 3x4 Matrix(Row0) R0 Cyan wire
KEYPAD 3x4 Matrix(Row1) R1 Pink wire
KEYPAD 3x4 Matrix(Row2) R2 Orange wire
KEYPAD 3x4 Matrix(Row3) R3 Gray wire
6

Proximity Reader with KEYPAD
INPUT
LED Control LED Brown wire
Beeper Control BEEP Blue wire
8. Wire Connection to Controller
8-1. 26bit Weigand+RS232(for Card) and 8bit Burst format(for PIN)
-The Reader transmits Card data to Wiegand Data0, Data1 and RS-232 TX line.
-The Reader transmits PIN data to Wiegand Data0 and Data1. (8bit Burst format.)
8-2. ABA Track II+RS232(for Card) and ABA Track II+RS232(for PIN)
- The Reader transmits Card & PIN data on card presentation, Clock, DATA and RS-232 TX line.
※NOTE: You have to enter at least 1 numeric number (max. 8 numbers) followed by "ENT" key.
7

Proximity Reader with KEYPAD
9. Operation
9-1. Connector Layout
9-2. Output mode Setting
Table 1. Jumpers Setting
JP1 JP2 Card Output format Keypad Output format
close close 26bit Wiegand + RS232 8bit Burst (or 3x4 Matrix)
open close 26bit Wiegand + RS232 26bit Wiegand + RS232(or 3x4 Matrix)
close open ABA Track II + RS232 8bit Burst (or 3x4 Matrix)
open open ABA Track II + RS23 ABA Track II + RS232 (or 3x4 Matrix)
※Note: Default setting value for JP1 and JP2 jumpers are “close”(short circuit)
8

Proximity Reader with KEYPAD
9-3. Operation
1. Once the power is applied, you should hear 3 initial beeps and red and yellow LEDs on
indicating that the reader is in standby mode after a successful initialization and diagnostics.
2. Present a proximity card to the reader until you hear the beeping sound and the green LED
come on. The reader will send the RF card data to the controller then the yellow LED on again
for the next reading.
3. Enter the Keypad until you hear the beeping sound. The reader will then send the Key data to
the controller.
4. LED Control:
To change the LED colours, you may connect the LED Control Input (brown wire) to ground
and the green LED will turn on indicating that the reader is in standby mode. Presenting a
proximity card and the LED will then change colour to yellow then green again for the next
reading.
5. Beeper Control:
In normal operation, the reader generates one beep when it reads a proximity card, However
additional beeps can be generated to improve indication for access status (granted or denied)
by forcing the Beeper Control Input, (blue wire) to system ground level. The beeper will remain
on as long as the blue wire is connected to system ground.
10. Output Format
10-1. 26bit Wiegand output format
1. Data format
Bit 1 : Even parity of bit 2 ~ bit 13
Bit 2∼9 : Facility code (000 ~ 255)
Bit 10∼25 : ID number (00000 ~ 65,535)
Bit 26 : Odd parity of bit 14 ~ bit 25
2. Timing diagram
9

Proximity Reader with KEYPAD
10-2. ABA Track II Magstripe output format
1. Data format (for Card numbers)
2. Data format (for PIN)
10

Proximity Reader with KEYPAD
3. Timing diagram
10-3. 8bit Burst output format (for PIN)
1. Data format
2. Timing diagram
11

Proximity Reader with KEYPAD
10-4. RS-232 output format
1. Data format (Baud rate: 9600bps)
2. Data structure
+15V
-15V
+3V
-3V
Space (=0)
Mark (=1)
8 Data Bits
2 Stop Bits
Indeterminate
Region
Data packet corresponding to ASCII character 'A'
Start Bit
010000010
LSB MSB
0V
START(0X02H) DATA (8 Char) END (0x03H) LRC (CARD output)
START(0X02H) DATA (1~8 Char) END (0x03H) LRC (Keypad output)
10-5. Matrix (3x4) format
1. Data format
Column0 Column1 Column2
↓↓↓
Row0 →1 2 3
Row1 →4 5 6
Row2 →7 8 9
Row3 →ESC 0 ENT
12

Proximity Reader with KEYPAD
11. Warranty and Service
The following warranty and service information applies only to the United States of America and
Republic of Korea. For the information in other countries, please contact your local distributor.
To obtain in or out of warranty service, please prepay shipment and return the unit to the service
facility listed below.
IN THE UNITED STATES
RF Logics Inc. Service Center
370 Amapola Ave, #106
Torrance, CA 90501
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
Web-site: www.rflogics.com
OUTSIDE OF THE UNITED STATES
IDTECK CO., LTD. Service Center
5F Ace Techno Tower B/D,
684-1 Deungchon-Dong, Gangseo-Gu,
SEOUL, KOREA 157-030
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
Web-site: www.idteck.com
13

Proximity Reader with KEYPAD
12. RMA Request Form
•RMA REQUEST FORM : ORIGINAL
IDTECK Co., Ltd.
5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea
TEL : [phone], FAX ; [phone], www.idteck.com
RMA REQUEST FORM
RMA No. & Date :
Original Invoice No. & Date :
Send to: RMA Customer Service
5F, Ace Techno Tower B/D 684-1,
Deungchon-Dong, Gangseo-Gu
Seoul, 157-030, Korea
Sales Person In Charge Requested from :
Shipping Port :
Air / Vessel : Departure Date :
NO Model Serial Number Error Check Box by shipper
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
1 Engineer
Comment
Others □:
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
2 Engineer
Comment
Others □:
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
3 Engineer
Comment
Others □:
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
4 Engineer
Comment
Others □:
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
5 Engineer
Comment
Others □:
Manufacture’s Verification
Product Defective :
User’s Misuse :
Communication Error :
Installation Error :
Connection Error :
Others :
Packing Details
Dimension(L:W:H): No.ofUnits:
Net&GrossWeight: No.ofBoxes:
Requestedby: Receivedby:
SignatureofBuyer SignatureofIDTECK
14

Proximity Reader with KEYPAD
•RMA REQUEST FORM : SAMPLE
IDTECK Co., Ltd.
5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea
TEL : [phone], FAX ; [phone], www.idteck.com
RMAREQUEST FORM
RMA No. & Date :. We will send this No. , if needed.
Original Invoice No. & Date : 00-00-0-000 / 2005.10.01
Send to: RMA Customer Service
5F, Ace Techno Tower B/D 684-1,
Deungchon-Dong, Gangseo-Gu
Seoul, 157-030, Korea
Sales Person in Charge:
Karina Kwak
Requested from :
Mr. XXXX YYYY
ABC Company
Address:
Country:
Shipping Port : Narita
Air / Vessel : Air Departure Date : 2005, 10. 15
NO Model Serial Number Error Check Box by Shipper
SR 10 XXXXXXXXXXXXX RS 232 Com. □
Input/Output □
Power ▣
Keypad □
Card Reading ▣
RS 422 Com □
1 Engineer
Comment
Write problem (must be
detailed). Others □:
others RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
2 Engineer
Comment
Others □:
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
3 Engineer
Comment
Others □:
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
4 Engineer
Comment
Others □:
RS 232 Com. □
Input/Output □
Power □
Keypad □
Card Reading □
RS 422 Com □
5 Engineer
Comment
Others □:
Manufacturer’s Verification
Product Defective :
User’s Misuse :
Communication Error :
Installation Error :
Connection Error :
Others :
Packing Details
Dimension(L:W:H) : 30 * 25 * 80 No.ofUnits: 20
Net & Gross Weight : 150g No.ofBoxes: 2
Requestedby: Receivedby:
XXXX YYYY
SignatureofBuyer SignatureofIDTECK
15

Proximity Reader with KEYPAD
The specification contained in this manual are subject to change without notice at any time.
5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong,
Gangseo-Gu, Seoul, 157-030, Korea
Tel : [phone]
Fax : [phone]
E-mail :
[email protected]
OCT. 2005 Copyright ©2005 IDTECK Co., Ltd.