IDW G-2 User manual

INSTRUCTION MANUAL
G-2
WWW.IDW-USA.COM.

1
TABLE OF CONTENTS
Parts and Identification …. ………………………… …. 1
Safety and Instructions …. ………………………… … .. 2
Installation………………………………………… … … .2
Electric Connection……………………………… …… … 2
Start…………………………………………………… … 3
Light Control…………………………………………… . .3
Maintenance………………………………………… … 3
Cleaning…………………………………………… … . .3
Light Replacement……………………………………. ..4
Power Failure…………………………………………. ...4
Moving the cooler…………………………………… ….4
Drip Pan………………………………………………….4
Troubleshooting…………………………………………….5
Circuit Diagram……………………………………………..6

2
PARTS AND INDENTIFICATION
A. Cabinet D. Drip pan
B. Glass Door E. Compressor
C. Lock F. Adjusting Leg

3
BEFORE USING, PLEASE READ ALL INSTRUCTIONS
SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock, or injury when using your cooler,
please note the following basic precautions:
•Never clean appliance parts with flammable fluids.
•Do not store or use gasoline or any other flammable vapors and liquids in the
vicinity of this or any other appliance. The fumes can cause a fire or explosion.
•As with all electrical appliances, please consult a licensed repair technician
for any repairs.
INSTALLATION
•Keep in upright position for 1-hour prior to use. This is essential for proper operation.
oIf the cooler is transported in the horizontal position, the cooler must be returned to the
upright position and not plugged in for 1 hour.
•Remove all the packing material before using your cooler.
•Clean the interior surface with a soft cloth and lukewarm water.
•If the cooler is transported in the horizontal position, check the drain pan and ensure that it is
properly positioned above the compressor.
•For proper operation, place the cooler on a dry, level surface.
•Place the cooler at least 4” away from any walls. Otherwise, this could cause damage to the
electrical cord and block the air circulation to the appliance.
ELECTRIC CONNECTION
•Our models operate with an 115V-60Hz-power supply. Check the electrical outlet for proper
voltage.
•Warning: Plug unit directly into wall outlet. Do not use an extension cord or any other multiple
connectors.
•For your safety, plug unit into a grounded wall outlet.

4
START
•Plug the cooler into the electrical outlet. For optimum performance, run cooler for three hours
prior to use.
•Temperature Control: Do not adjust the temperature control. The temperature control is factory
set to provide maximum performance.
LIGHT CONTROL
•Lights operate automatically when unit is plugged in.
MAINTENANCE
Cleaning
•Before cleaning the appliance, always remember to unplug it.
•Unplug the cooler at the electrical outlet; never pull the service cord.
•Do not use sharp or pointed objects for cleaning.
•Clean the inside cabinet of the cooler with a clean damp cloth or with neutral soap. Avoid
damage by using non-abrasive or flammable cleaning products.
•Clean the condenser at least once a month with a vacuum cleaner or a brush to eliminate the dust
accumulation.

5
Light Replacement
•Unplug the cooler before removing the light.
•Remove the screw.
•Remove the light cover gently.
•Remove the light.
•Replace the light with the equivalent fluorescent bulb.
•Install the light cover and tighten the screw.
Power Failure
•Please minimize the frequency of opening the door during a power failure.
•If your cooler is unused for an extended period of time, unplug, empty, and clean your cooler.
Keep the door open to avoid condensation, formation of molds, or odors.
Moving the cooler
•Empty the unit.
•Secure all loose parts inside the cooler.
•Tape the door shut.
•During transportation, make sure that the cooler is in an upright position.
Drip Pan
•During normal compressor cycle, water will drain into the drain pan and evaporate.
•To clean, pull the drain pan forward gently and reinstall it after cleaning.

6
TROUBLESHOOTING
If your cooler is not working properly:
•Check the electrical outlet for power, and that the plug is properly inserted.
•Check to see if the circuit breaker is tripped or the fuse is blown.
•Check the condenser for proper cleaning.
If your cooler is making noise:
•Check that the cooler is level and on a flat surface.
If the compressor turns on and off frequently:
•The room temperature is higher than normal.
•The door is not closed completely.
•The door gasket is not sealed well.
•There is insufficient clearance around the cooler.
•The temperature is not set properly.
•The cycling frequency will reduce when all of the cans reach the set temperature.
The following is not a malfunction:
•It is normal to hear gurgling sounds caused by the flow of refrigerant when each cooling cycle
ends.
Refrigerant
•Your G-2 cooler utilizes R134a refrigerant.

7
CIRCUIT DIAGRAM