IFM Electronic AL2230 User manual

Operating instructions
IO-Link module
AL2230
AL2330
7391119 / 00 06 / 2017
UK
Original Scale Drawing (MTD)
EPS Source
Product Scale Drawing
Frame Size: 80 mm x 58,5 mm
P_MZ_e500_0001
30% 333,4%
LED
M12x1
26
34
38
LED
M12x1
26
34
38
152
136
59,3
5,2

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������3
2 Safety instructions �����������������������������������������������������������������������������������������������3
3 Functions and features ����������������������������������������������������������������������������������������3
3�1 IO-Link �����������������������������������������������������������������������������������������������������������3
3�1�1 General information ������������������������������������������������������������������������������3
3�1�2 Device-specific information�������������������������������������������������������������������3
3�1�3 Parameter setting tools ������������������������������������������������������������������������4
3�1�4 Response when the IO-Link communication is interrupted ������������������4
4 Function���������������������������������������������������������������������������������������������������������������4
4�1�1 Electrical isolation of the voltage supply ����������������������������������������������4
4�1�2 Visual indication������������������������������������������������������������������������������������4
4�1�3 Parameter setting ���������������������������������������������������������������������������������4
4�1�4 Digital outputs���������������������������������������������������������������������������������������4
4�1�5 Separate deactivation of the outputs ����������������������������������������������������4
4�1�6 Variable output currents������������������������������������������������������������������������5
4�1�7 Response in case of undervoltage �������������������������������������������������������5
5 Installation������������������������������������������������������������������������������������������������������������5
6 Electrical connection��������������������������������������������������������������������������������������������5
6�1 IO-Link connection�����������������������������������������������������������������������������������������6
7 Pin connection �����������������������������������������������������������������������������������������������������6
8 Operating and display elements ��������������������������������������������������������������������������7
8�1 LEDs��������������������������������������������������������������������������������������������������������������8
9 Scale drawing ������������������������������������������������������������������������������������������������������9
10 Technical data����������������������������������������������������������������������������������������������������9
10�1 IO-Link device��������������������������������������������������������������������������������������������10
11 Maintenance, repair and disposal ��������������������������������������������������������������������10
11�1 Cleaning the housing surface ��������������������������������������������������������������������10
12 Approvals/standards ���������������������������������������������������������������������������������������� 11

3
UK
1 Preliminary note
►Instructions
> Reaction, result
Important note
Non-compliance may result in malfunction or interference�
Information
Supplementary note�
2 Safety instructions
• Please read the operating instructions prior to set-up of the device� Ensure that
the product is suitable for your application without any restrictions�
• The unit complies with the relevant regulations and EC directives�
• Improper or non-intended use may lead to malfunctions of the unit or to unwan-
ted effects in your application�
• Installation, electrical connection, set-up, operation and maintenance of the unit
must be carried out by qualified personnel authorised by the machine operator�
3 Functions and features
The AL2230 unit has a grey housing and is suitable for use in the food and beve-
rage industry (use of cleaning agents at high pressure and high temperatures)�
The AL2330 unit (orange) must not be used in these areas�
3.1 IO-Link
3.1.1 General information
The unit has an IO-Link communication interface which requires an IO-Link capa-
ble module (IO-Link master)�
The IO-Link interface enables direct access to diagnostic data and provides the
possibility to set the device parameters during operation�
3.1.2 Device-specific information
You will find the IODDs necessary for the configuration of the IO-Link unit and
detailed information about process data structure, diagnostic information and
parameter addresses at www�ifm�com

4
3.1.3 Parameter setting tools
You will find all necessary information about the required IO-Link hardware and
software at www�ifm�com
3.1.4 Response when the IO-Link communication is interrupted
The parameter "Output state COM lost / PD invalid" (index 15000) is used to set
how the outputs are to respond when the IO-Link communication is interrupted�
For every output it can be defined separately if it:
- is to be switched on (HIGH)
- is to be switched off (LOW)
- or is to keep the last state
4 Function
After power on, the unit is in the RUN mode (normal operating mode)�
4.1.1 Electrical isolation of the voltage supply
The voltage supply of the outputs is electrically isolated from the IO-Link master�
Moreover, the voltage supplies of the left and right side are electrically isolated in
the device (UA left and UA right to connector X31)�
4.1.2 Visual indication
The unit
- indicates the current state of an output (yellow LED DO1/DO2)
- signals a correct operation (green LED UAL/UAR on, red LED L/R off)
4.1.3 Parameter setting
Device-specific parameter lists for IO-Link parameter setting are available at
www�ifm�com
4.1.4 Digital outputs
The unit has 6x2 digital outputs�
4.1.5 Separate deactivation of the outputs
The outputs of the left side are electrically isolated from the outputs of the right
side� Therefore the outputs of one side can be switched off without switching off
the outputs of the other side� This does not disturb the IO-Link communication�

5
UK
4.1.6 Variable output currents
The unit monitors the total currents of both output sides� 1800 mA can be switched
on every side� The individual outputs have no additional current limitation and can
therefore be loaded variably� If the total current of an output side is too high, the
unit switches off this side� To activate again the outputs of this side the voltage
supply must be disconnected and connected again� The activation of deactivated
outputs can also be made via IO-Link (send a "PDout": bytes 0 and 2 are set to 0,
reset of the outputs left, bytes 1 and 3 are set to 0, reset of the outputs right)�
4.1.7 Response in case of undervoltage
If the voltage supply of the outputs falls below 16�5 V, all outputs switch off�
5 Installation
►Disconnect the system from power before installation�
►For installation choose a flat mounting surface�
►Fasten the module onto the mounting surface using M5 screws and washers�
Tightening torque 1�8 Nm�
►Connect the plugs of the sensors to the M12 sockets�Tightening torque max� 1
Nm�
►Cover unused sockets with protective caps (E12542)�
Tightening torque 0�6���0�8 Nm�
Observe the maximum tightening torque of the connection cables�
6 Electrical connection
The unit must be connected by a qualified electrician�
The national and international regulations for the installation of electrical
equipment must be adhered to�
Voltage supply according to SELV, PELV
►Disconnect power�
►Connect the unit�

6
Do not connect more than 30 m of cable to the outputs�
Do not apply external voltage to the outputs�
6.1 IO-Link connection
The IO-Link port must be connected according to the IO-Link specification�
7 Pin connection
M12 connector IO-Link (X1)
1: + 24 V DC (US)
2: not connected
3: GND (US)
4: IO-Link
M12 connector Power AUX (X31)
1: + 24 V DC (UAL)
2: GND (UAR)
3: GND (UAL)
4: + 24 V DC (UAR)
Outputs left (X1.0, X1.2, X1.4)
1: not connected
2: output DO2
3: GND (UAL)
4: output DO1
5: not connected
Outputs right (X1.1, X1.3, X1.5)
1: not connected
2: output DO2
3: GND (UAR)
4: output DO1
5: not connected

7
UK
8 Operating and display elements
5
6
7
6
7
6
7
6
7
6
7
6
7
88
9
1
2
34
1: LED INT
2: LED L
3: LED R
4: LED UAL
5: LED UAR
6: LED DO2
7: LED DO1
8: LED
9: LED US
internal fault
fault on the left side
fault on the right side
voltage supply left ok
voltage supply right ok
status output DO2
status output DO1
IO-Link communication
supply voltage

8
8.1 LEDs
LED Colour Status Description
INT red on internal fault
L red on short circuit or undervoltage on the left side
off no fault on the left side
unit in the operating mode
R red on short circuit or undervoltage on the right side
off no fault on the right side
unit in the operating mode
UAL green on voltage supply on the left side ok
off voltage on the left side < 16�5 V
UAR green on voltage supply on the right side ok
off voltage on the right side < 16�5 V
DO1, DO2 yellow on output signal high
off output signal low
green on IO-Link communication active
US green on voltage supply ≥ 17 V
off voltage supply < 17 V

9
UK
9 Scale drawing
Original Scale Drawing (MTD)
EPS Source
Product Scale Drawing
Frame Size: 80 mm x 58,5 mm
P_MZ_e500_0001
30% 333,4%
LED
M12x1
26
34
38
152
136
59,3
5,2
LED
M12x1
26
34
38
152
136
59,3
5,2
Dimensions [mm]
10 Technical data
AL2230 AL2330
Operating voltage DC [V] 18���30
Nominal voltage DC [V] 24
Power consumption
PUS [W] 1�5
PUA [W] 4
Output function transistor PNP
Max� total current per output side [mA] ≤ 1800
Housing polyamide, grey,
socket: stainless steel
(1�4404/316L)
polyamide, orange,
socket: nickel-plated
brass
Protection rating IP 68 / IP 69K IP 67
Ambient temperature [°C] -25…60

10
Storage temperature [°C] -25…70
Max� permissible relative
humidity
[%] 5���75
Maximum operating altitude [m] 2000 above sea level
Permissible air pressure [hPa] 750���1060
Connectors M12 connector, 4 poles
M12 socket, 5 poles
10.1 IO-Link device
Transmission type COM2 (38�4 kbaud)
IO-Link revision 1�1
SDCI standard IEC 61131-9
IO-Link device ID 893 d / 00 03 7d h
SIO mode no
Input load current at input C/Q
to V0
[mA] < 50
Required master port type A
Number of digital outputs 12
Data length digital outputs [Byte] PDout: 4 / PDin: 8
Min� process cycle time [ms] 5�6
11 Maintenance, repair and disposal
The operation of the unit is maintenance-free�
After use dispose of the unit in an environmentally friendly way in accordance with
the applicable national regulations�
11.1 Cleaning the housing surface
►Disconnect the unit�
►Clean the unit from dirt using a soft, chemically untreated and dry cloth�
►In case of heavy dirt, use a damp cloth�
Micro-fibre cloths without chemical additives are recommended�

11
UK
12 Approvals/standards
EC declarations of conformity, approvals etc� can be downloaded at: www�ifm�com
Other manuals for AL2230
1
This manual suits for next models
1
Table of contents
Other IFM Electronic I/O System manuals

IFM Electronic
IFM Electronic Ecomot300 AC2630 Application guide

IFM Electronic
IFM Electronic Ecomat 100 CR2014 Application guide

IFM Electronic
IFM Electronic AL1202 User manual

IFM Electronic
IFM Electronic AL19 User manual

IFM Electronic
IFM Electronic AC030S User manual

IFM Electronic
IFM Electronic CR2513 Application guide

IFM Electronic
IFM Electronic CR2013 Application guide

IFM Electronic
IFM Electronic AL1200 User manual