ICP DAS USA I-7053 FG User manual

I-7053_FG - 16-channel DI DAQ Module- QuickStart (Nov/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
I-7053_FG
16-channel Non-isolated Digital Input Module
with 16-bit Counters
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/i_7053_fg
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
I-7053_FG features long distance measurement for digital input. Its
effective distance for dry contact is up to 500 meters. I-7053_FG supports
source type input. All of its 16 channels are also able to be used as 16-bit
counters, each of which features non-isolated. I-7053D_FG has 16 LED
indicators for channel status.
2. Terminal Assignment

I-7053_FG - 16-channel DI DAQ Module- QuickStart (Nov/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram

I-7053_FG - 16-channel DI DAQ Module- QuickStart (Nov/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
4. Default Settings
Default settings for the I-7000 DIO modules are as follows:
。Module Address: 01
。DIO Type: Type 40
。Baud Rate: 9600 bps
。Checksum disabled
5. Configuration
To install the module, follow the steps below:
1. Connect the digital output.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.

I-7053_FG - 16-channel DI DAQ Module- QuickStart (Nov/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.

I-7053_FG - 16-channel DI DAQ Module- QuickStart (Nov/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC

I-7053_FG - 16-channel DI DAQ Module- QuickStart (Nov/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
7. For I-7000 modules, DCON utility pro terminal can send command to the module.
See user manual Sections 2 for details command.
Configure the module: sending the %AANNTTCCFF command. See user manual
Section 2 for details.
Read data from the input channels: send either the #AA or #AAN command to the
module.
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.