IGO Audio HAV-R400G User manual

1 2
650-AVR502-01
HOME THEATRE RACK SYSTEM
INSTALLATION GUIDE
HAV-R400G/HAV-R500G
OTHE ASSEMBLY PROCESS SHOULD BE DONE BY TWO OR MORE PEOPLE.
OUSE A SUITABLE SCREW DRIVER FOR THE ASSEMBLY PROCESS.
ODO NOT USE GLUE/ADHESIVE TO ASSEMBLE THE RACK AS THIS MAY JEOPARDIZE ITS SERVICEABILITY.
OTO PREVENT SPEAKER DAMAGE, DO NOT HOLD THE CLOTH FRAME DURING ASSEMBLY.
OALL ASSEMBLY STEPS SHOULD BE COMPLETED TO ENSURE SAFE OPERATION OF THIS UNIT.
ORISK OF PINCHING DURING THE ASSEMBLY PROCESS - TAKE EXTRA CARE.
OINSTALL THIS UNIT NEAR AN ELECTRICAL OUTLET FOR EASY ACCESS.
1List of Parts
Please make sure that the following accessories are
included in the package.
OTop glass OTop box
G A
OBottom board OShelf board × 2
DI
OSW box × 2 OCenter pillar
CB
OLong bolt × 3 OHAV-R400G: Caster tray × 2
HAV-R500G: Caster tray × 4
EJ
OHAV-R400G: Caster × 5
HAV-R500G: Caster × 8
OMetal shelf pin × 8
FH
2Installation
The illustrations below show HAV-R400G. The visual
appearance of HAV-R500G is slightly different from the
illustrations.
ATurn the top box Aas shown in the illustration.
AA
BPlace the center pillar Band SW box C.
C
C
B
CPlace the bottom board D.
D
DSecure the theatre rack with 3 long bolts E.
Spring washer
Cushion
Flat washer
E
Installation continued
EInsert the casters Fon bottom board.
FF
FF
HAV-R400G
HAV-R500G
• If you do not need to install the casters, skip this process.
FTurn the theatre rack as shown in the illustration.
HAV-R400G_R500G_IG.indd 1HAV-R400G_R500G_IG.indd 1 10/12/2011 5:29:35 PM10/12/2011 5:29:35 PM

3 4
Printed in Malaysia
GPlace top glass Gon top of the unit and align properly.
G
HConnect SW wire.
Connect Gray withConnect Gray with
Black Stripe WireBlack Stripe Wire
to — (Black Button)to — (Black Button)
Connect GrayConnect Gray
Wire to +Wire to +
(Gray Button)(Gray Button)
Connect GrayConnect Gray
with Blackwith Black
Stripe Wire to —Stripe Wire to —
(Black Button)(Black Button)
Connect GrayConnect Gray
Wire to +Wire to +
(Gray Button)(Gray Button)
• Press the button to insert wire into the hole.
Installing the caster trays
• Install the caster trays J(supplied) under the casters so
that the unit does not move.
• Make sure the caster trays are installed by two or more
people.
Place the caster trays under the front casters
Align the caster with
the groove on the
caster tray.
Groove
Caster tray
(supplied)
J
HAV-R400G
HAV-R500G
About the installation position
• For safety, wear gloves when installing or moving the unit.
• To prevent injury, two or more people are required to lift
this unit.
• Be careful not to pinch your fingers when installing the
rack.
• The bottom surface of the unit is equipped with casters.
Be extra careful not to damage the floor with the casters.
Avoid going over uneven or unlevel surfaces with the
casters.
• Do not touch or press the cloth frame of the speakers or
subwoofer while installing or moving the unit. Doing so
may cause damage to the cloth of the speaker or the
speaker itself.
Installation continued
QAllow sufficient space around the unit
• Allow for a space of about 4" (10 cm) above, behind and
around the unit to avoid blocking the ventilation holes of
the amplifier and Subwoofer speakers for better sound.
About 4" (10 cm) away from the wall
Removing the casters
• Remove the casters if you wish to install the unit on an
unstable surface such as a thick-piled carpet.
• Carefully remove the top glass, shelf boards and metal
shelf pins before putting them in a safe place.
• To prevent injury, two or more people are required to lift
this unit.
• Place a soft sheet on the floor and lay the unit on its back
on the sheet.
• Remove the casters by grasping and pulling them.
• After the casters have been removed, please repeat step
F, G, Iand J.
Grasp and pull
the casters
Bottom side
A soft sheet
Installation continued
IInsert the metal shelf pins Hinto the pin holes on the
center pillar and SW box .
HH
JPlace the shelf boards Icorrectly on top of the metal
shelf pins.
Slot (on the bottomSlot (on the bottom
side of the shelf board)side of the shelf board)
I
• Shelf board height can be adjusted to 3 levels. (Refer to the “User’s
Manual” for details.)
• Even when no shelf board is installed, leave the support pins (supplied) in
the holes to prevent losing parts.
• If the shelf board is placed in the wrong direction or storage compartment,
the equipment installed on it may fall.
• Put the supplied shelf board straight into the storage compartment and
place it flat, aligning the slots on the bottom side of the shelf board with
the metal shelf pins.
HAV-R400G_R500G_IG.indd 2HAV-R400G_R500G_IG.indd 2 10/12/2011 5:29:36 PM10/12/2011 5:29:36 PM