iHome BONTEC ST12 User manual

1
Installation Instruction
English
UNPACKING INSTRUCTIONS
! Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
! Check package contents against the Supplied Parts List in the next page to assure that all components were received
undamaged. Do not use damaged or defective parts.
! Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before beginning the installation, and carefully
follow all instructions contained herein. Use proper safety equipment during installation.
Please call a qualified installation contractor for help if you:
! If you don't understand these directions or have any doubts about the safety of the installation.
! If you are uncertain about the nature of your wall, consult a qualified installation contractor.
Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby
disclaim any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of
this product.
ST12

(1)TV Plate-a (2)Monitor Bracket-b
2
Supplied Par ts List
(1)Tempered Glass-c (1)Support Column-d
(4)M4x12 Bolt-n (4)M4x30 Bolt-o (4)M6x20 Bolt-p (4)M8x20 Bolt-r
(4)M8x45 Bolt-s (4)M4 Washer-t (7)M6 Washer-u (4)M4 Spacer-w
(8)M6/M8 Spacer-x
(1)Plastic Socket-e (1)Metal Pad-f
(1)Allen Key-y
(2)Wire Clip-j (4)Rubber Foot-k
(1)Secuity Wire Kit-z
(1)Swivel Pad-g (2)M6x14 Bolt-h
(3)M6x18 Bolt-i (4)M6x10 Bolt-l
(4)M8 Washer-v
(4)M6x35 Bolt-q
(4)Metal Washer-m
(4)M4x6 Bolt-B(2)Buckle-A

3
Connecting the Support Column to Tempered Glass
Step 1
c
k
1.1
1.2
d
g
h
y
1.2
f
u
y
1.2
1.3
i
1.2
1.4
e

4
Connecting the TV Plate to Support Column
Step 2
y
a
2.1
l
m
Height
Adjustable
2.2
j

5
Attaching TV To TV Plate and Managing the Wires
Step 4
Mounting the Monitor Brackets to a TV
Step 3
First of all, Once you have determined the correct diameter,
please see the diagram as below. You will thread the Bolt into the TV using the correct Washer(t,u,v), and using the
spacer(w,x) if necessary. Please make sure the Monitor Brackets are vertically centered and level with each other.
make sure the diameter of the Bolt(n to s) your TV requires.
4.4
4.3
t,u,v
n to s
w,x
Hang the TV onto Stand, there are two gears
that can be adjusted!
A
B
4.1
4.2
Hang the TV on the brackets(a) and adjust the position.
Then use the screwdriver to lock the buckle(A) and screws(B) tight.

6
Attaching the Security Steel Wire to the TV
Step 5
If your TV is located nearby the wall as the Diagram 5a, then a steel wire can be attached for added security. Attaching the
two ends of steel wire to the top two holes on the back of TV, shown in Diagram 5b.
Attaching the another end of steel wire to the wall according to your wall type, shown in Diagram 5c, 5d and 5e.
50mm
8mm
45mm
3.8mm
Wood Stud Wall
Concrete & Brick Wall
Diagram 5a Diagram 5b
Diagram 5e
Wall
Diagram 5c
Diagram 5d