iHome iBT372 User manual

instruction manual
Model: iBT372
CHARGE
BEFORE
USE
Waterproof & Shockproof
Wireless Stereo Speaker

Introduction
Thank you for purchasing the iHome iBT372. This product is designed to
provide high quality wireless sound for your Bluetooth audio device
wherever you take it. iP67 rating means the unit is tested to be waterproof
and dustproof. It also meets military specs for being shockproof.
This instruction booklet explains the basic operation and care of the unit.
Please read it carefully and keep for future reference.
Maintenance
• Place the unit on a level surface away from sources of direct sunlight or
excessive heat.
• Protect your furniture when placing your unit on a natural wood and
lacquered finish. A cloth or other protective material should be placed
between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water.
Stronger cleaning agents, such as thinner or similar materials can damage
the surface of the unit.
iBT372
1

iBT372
What’s Included
• iBT372 speaker
• USB charging cable
• Carry strap
2
Carry strap
USB charging cable
iBT372

iBT372
IMPORTANT INFORMATION ABOUT
WATERPROOF OPERATION
2
For proper waterproof operation, make sure the waterproof
cover on the right side of the unit is completely flush with the
unit by pressing along the entire edge of the cover until it is
completely and securely in place.
• The unit is IP67 waterproof rated, meaning it is immersible
for up to 30 minutes at a depth of 1 meter (3 feet). It will
typically withstand rain, snow and being submersed in
shallow water. Longer duration or deeper immersion that
exceeds the tested limits may cause product failure and
void the warranty.
• DO NOT immerse the unit in water for extended periods.
• DO NOT immerse the unit in water deeper than 1 meter
(about 3 feet).
• Make sure cover and surrounding surfaces are completely
dry before opening cover to prevent moisture from
damaging the internal electronics.
• Keep rubber cover free of dirt, sand, or other objects that
can interfere with proper sealing. If for any reason the
waterproof cover is not making a tight waterproof seal
water may enter the unit.
• Rinse with tap water after immersion in salt water or
swimming pool.
• DO NOT clean unit with oily soaps or use chemicals or
solvents. Clean with damp cloth.
water
tight
not
water
tight

iBT372
Front
Right Side
(under rubber seal)
Microphone
USB In
Charging Port
Aux-in Jack
Reset Port
Meet Your iBT372
Top
Power Button
Battery Status Indicator Lights
(portable/battery mode only)
Bluetooth Status
Indicator Light
3
Color Mode/
Battery Review
Button
Lower/Raise
Volume Buttons
Bluetooth/
Speakerphone
Button
Play/Pause/
Button

Getting Started: Carry Strap
The iBT372 has a channel on the left side of the
unit to attach the included carry strap. To attach
the carry strap, form a small loop in one end of
the carry strap. Insert this loop through the
desired channel, then pull the loop back through
the larger loop formed in the carry strap to
tighten.
Charging the Unit
CHARGE UNIT BEFORE USE/KEEP UNIT OFF FOR FASTER CHARGING
1. Connect the micro USB plug on the included USB charging cable to the
micro USB IN Charging USB Port on the right side of the unit under the
rubber seal.
2. Connect the standard USB plug end of the cable to a power USB port
on a computer, a USB AC adaptor or other USB charging device. For
first time use, charge unit for about 5 hours. The status indicator LEDs
on front of the unit cycle progressively while charging and turn solid
once unit is fully charged.
iBT372
4
Charge via computer USB port, USB AC adaptor or other powered USB port
iHome iBT372 USB In
Charging port
USB AC adaptor
(not included)
USB AC adaptor
connected to working outlet

Reviewing Battery Charge Level
(Portable/Battery Mode: Charger is Disconnected and unit is
ON)
When unit is ON but not charging (operating on battery, micro USB
cable not connected) you can review the current battery status on the
Battery Status Indicator Lights (four white LEDs on front of the unit
above the iHome badge) any time a button is pressed.
5
TIP: On some iOS (Apple)
devices, you can view the
iBT372 battery status on your
device’s screen. When device is
paired and connected, look for a
vertical battery icon next to the
Bluetooth icon on the upper
right corner of the
device’s screen.
iBT372
Battery
dead
(no charge)
Battery
low
(needs
charging)
Battery
half
charged
Battery
good
mostly
charged
Battery
fully
charged
Battery Indication During Charging
While the battery is charging, the Battery Status Indicator Lights
will flash in a continuous cycle showing progressively fuller battery.
The LEDs will stop flashing once the battery is fully charged.

Pairing Your Device
Pairing is the set-up process to introduce your Bluetooth-capable device to
the iBT372. Once your device is paired, the iBT372 can recognize it and you
can play your audio through it.
1. Turn on your Bluetooth device and make it “discoverable”
by turning on Bluetooth mode (check in Options or
Settings).
2. Press and hold the Power Button for 2 seconds to turn on
the iBT372. The first time the unit is powered on, it will
enter auto-pairing mode: the unit will beep, the
Bluetooth status indicator light on front of the unit will
flash quickly and a voice will announce “PAIRING” while
the unit attempts to pair. (If Color Mode is on, the accent
lights will flash blue and red.)
3. “iHome iBT372” should appear in your device’s Bluetooth
menu. Select “iHome iBT372” on device to complete
pairing. If prompted for a passcode, enter “1234” on your
device’s keypad. 1 beep will sound, the voice will
announce “CONNECTED” and the Bluetooth status
indicator light will appear solid blue (in Color Mode,
cabinet will flash blue twice), indicating the iBT372 is
paired and ready to play music. There should also be an
indication on your device. If no device is successfully
paired within 3 minutes the iBT372 will default to previous
mode.
4. To pair with a dierent device or at a dierent time, make
sure unit is powered on, then press and hold the
Bluetooth/Speakerphone Button for 2 seconds. Select
“iHome iBT372” on device to pair.
Once the iBT372 is paired to a device, it will attempt to
autolink when the device is within range (about 33 feet).
To delete all Bluetooth paired devices from the iBT372,
press and hold the Bluetooth/Speakerphone Button for
10 seconds.
6
Using the iBT372
iHome iBT372

Playing Audio Via Bluetooth
1. Press and hold the Power Button for 2 seconds to turn on the unit. The Bluetooth
status indicator will glow solid blue when a linked device is in range and detected.
You can then listen to audio streamed wirelessly from your paired Bluetooth
device.
2. Press the Play/Pause/Voice Command Button to play and pause tracks.
3. Press the or Button to adjust the iBT372 volume. You can also adjust
volume on your device.
4. When done listening, press and hold the Power Button for 2 seconds to turn the
unit OFF.
Speakerphone Operation
NOTE: The unit must be powered on and linked to a Bluetooth phone to receive a
call.
1. When a call is received, playing music is muted to hear the ring tone and the
cabinet lights flash green. Press the Bluetooth/Speakerphone Button to
answer the call, or press and hold to reject the call. For call waiting function,
press the button again to answer a second call, and once more to return to the
original call. Press and hold to end the current call and return to a remaining
call.
2. When a call is completed, press the Bluetooth/Speakerphone Button to end
the call and resume previous function.
Voice Commands
NOTE: The unit must be powered on and linked to a Bluetooth phone to use voice
commands.
Press and hold the Play/Pause/Voice Command Button to access the voice
command protocol associated with your device’s operating system (Siri for iOS
devices, “OK, Google” for Android devices, etc.
7
Using the iBT372

Playing Audio via Aux In
1. Connect a standard stereo audio cable (not included) to the Aux-in Jack on the
right side of the unit and connect the other end to the headphone or line-out jack
on your audio device.
2. Press and hold the Power Button for 2 seconds to turn on the unit.
3. Power on the audio device and use the controls on the device to play or pause
audio and to navigate tracks.
4. Press the or Button to adjust the iBT372 volume. You can also adjust
volume on your device.
5. When done listening, press and hold the Power Button for 2 seconds to turn o
the unit. Remember to turn o your device, too.
NOTE: Any Bluetooth audio must be paused or you will not hear Aux-in audio.
Using Color Modes
There are six color modes, which you cycle through in this order:
a. Slow Fade (colors slowly fade from one into the next
b. Fast Change (colors change rapidly)
c. One Color (select a favorite color)
d. Pulse to Music (lights flash to the beat of the music)
e. Preset Pulsing (each light array pulses through its own preset pattern of colors)
f. O (no display)
1. Press and hold the Power Button for 2 seconds to turn on the unit
2. Press the Color Mode Button repeatedly to cycle to the desired color mode.
For One Color mode, first cycle to Fast Change mode and press the Color Mode
Button when the desired color appears. For Pulse to Music, make sure the
volume on your connected Bluetooth device is above 30%.
3. Press and hold the Power Button for 2 seconds to turn the unit o.
8
Using the iBT372