Ikan V8000T User manual

TouchKitTouch Panelv3.1.4 0
TouchKit TouchPanel
User manual
for MS-DOS
Version: 3.1.4

TouchKitTouch Panelv3.1.4 1
CONTENT:
CHAPTER1. TOUCH PANEL CONTROLLER.........................................................2
1.1CONTROLLER ....................................................................................................................2
1.2SPECIFICATIONS AND FEATURES ........................................................................................3
CHAPTER2. INSTALLINGAND USINGTOUCHKIT...............................................5
CHAPTER3. CONFIGURATION UTILITY ANDRIGHT BUTTONEMULATOR......6
CHAPTER4. UNINSTALLINGTOUCHKIT.............................................................10

TouchKitTouch Panelv3.1.4 2
Chapter 1. Touch Panel Controller
Thistouchpanelcontroller providestheoptimisticperformance ofanalog resistive
touch panels for 4wire, 5wire and 8wire models. It communicates withPCsystem
directlythrough RS232, PS/2or USB connector.user can see howsuperior the
design isinsensitivity,accuracyand friendlyoperation.The touch paneldriver
emulatesmouseleftandright button function andsupports operation systems
includingMicrosoftWindows95/98/ME/2000/NT/XP/XP Tablet PCEdition,Windows
CE 2.12/3.0/. NET, Linux, iMac and DOS.
1.1 Controller
Interface RS232 USB PS/2
4-wire ReadyReadyReady
5-wire ReadyReadyReady
8-wire ReadyReadyReady

TouchKitTouch Panelv3.1.4 3
1.2 Specifications and Features
Specificationsfor Touchkit controller.
Specifications
Power requirements +5VDC ( Maximum 100mA, typical70mA,
50mV peak to peak maximum ripple )
Operating temperature 0 to 50
Storage Temperature -40 to 80
Relative Humidity 95%at 60
ProtocolRS232 Model:9600 bauds, None parity,8data bits,
1
stop bit
USB Model: USB 1.1 Lowspeed
PS/2 Model:PS/2mouse
Resolution 2048 X 2048
Report rate RS232 Model:Max. 160 points/sec
USB Model: Max. 160 points/sec
PS/2 Model:Max.140 points/sec
Response time Resistive:Max. 35 ms
Capacitive: Max. 20 ms
Pinout definition 4 wire model: X,Y,X, Y
5 wire model: UL, UR, COM,LR,LL
8 wire model: X+, X+ref, Y+, Y+ref,
X- , X-ref,Y-, Y-ref
Panelresistance 4, 8wire resistive model:20
0~900ohm (pin topin
on the same layer )
5wire resistive model:50 ~200 ohm (pin to pin on
drive layer )
RegulatoryApprovalsFCC-B, CE

TouchKitTouch Panelv3.1.4 4
Features forTouchkit software
Features
Calibration 1. Fastfulloriental4 points position
2. Support monitor / displayrotation
3. Support multiple monitor / display
4. Support QVGA and Half-VGA function
Compensation Accuracy25 points linearitycompensation.
DrawTestPosition and linearityverification
Controller Setting 1.Support multiple controllers
2.Dynamicaladd /remove controllers
3.Change Controller interface without reboot.
Language Support 9languages for Windows
Mouse Emulator 1.Right / Left button emulation
2.Normal/ Click on touch / Click on release mode
3.Cursor visibility
Sound Notification 1.Nosound
2.Touch Down
3.Lift Up
4.Frequencyadjustment
5.Duration adjustment
Double Click 1.Configurable double click speed
2.Configurable double click area
OS support1.Windows95/98/ME/NT4/2000/XP/
WindowsXP Tablet PC Edition
2.WindowsCE 2.12, 3.0, .NET
3.Linux ( X WindowVersion: 3,4
Red Hat6.0 ~ 8.0
Mandrake 5.0 ~ 9.0 )
4.iMac.OS9
5.MS-DOS:
Support displayresolution: 320x200, 640x200
,
640x350, 640x480, 800x600,1024x768 and
1280x1024
COMport support 1.
Support COM1~COM256 for Windowsand
Linux
2.Support COM1~ COM8for DOS

TouchKitTouch Panelv3.1.4 5
Chapter 2. Installing and using TouchKit
TouchKit issoftware,which contains drivers ofthe touchpanel controllers for RS232
and PS/2, and utilities for controller configuration:
• Configuration support
Touchkit provides three program utilities for calibration and drawtest. Theyare
a.) tp4pcal.exe for 4points calibration
b.) tp25pcal.exe for 25 points calibration
c.) tpdraw.exe for drawtest
• Right button support
Thisisutilityfor emulatingtheright and leftbutton ofmouse through controlling
touch panel. User can toggle between right or leftmousebuttonswiththisutility.
This utilitysupports onlyvideo mode three.
Follow these stepstoinstall TouchKit.
1. Put the TouchKit CD to CD-ROM.
2. Change directoryto <CD-ROM drive>:\DOS\
3. Execute the installation program: INSTALL.BAT
For example:
Note: To enable mousecursor, pleaselaunch MOUSE.COM before launching TPANEL.EXE in
AUTOEXEC.BAT.Forex.
C:\DOS\MOUSE.COM
TPANEL.EXE
4. Rebootcomputer.
syntax: install<pathofdestination directory>
E:\DOS>installc:\
Destination C:\does notexist; shall Icreate it?(Y/n)
Change directoryto C:\
Copyfiles...
Copyfiles...Done
Append settings to C:\AUTOEXEC.BAT...
(Original C:\AUTOEXEC.BAT is saved as*.TKT)
Do you want to activate RightButton Tool? (Y,N)

TouchKitTouch Panelv3.1.4 6
Chapter 3. Configuration Utilityand RightButton Emulator
After installation TouchKit and rebooting system,the driver willprobe all
communication devices bydefault. Execute TPANEL -? for more options.
Note: If user attaches TouchKit controllerto another communication port,please
reboot computer.
To avoid confusing theend-user, TouchKit driver use the virtual TKT port name
instead of the com port name. In order version driver, TouchKit driver parsers the
com1and com2from the system environment. If theuserneedsanother comport,
forexamplecom5,all the end-user todo is set the environment variablesas set
COM1 = IOADDR,IRQ.However, this newdriver package use TKT instead of com.
Thissuitsupports atmosttwoserialports;which are TKT1 (IO:0x3F8 IRQ:4) and
TKT2 (IO:0x2F8 IRQ:3) bydefault. If BIOS settings differ (ex. COM1 isof IO addr
3E8 and IRQ4), add one more line (before TPANEL.EXE) in AUTOEXEC.BATto
redirect: SET TKT1 =3E8 4
Also, Ifthe user needsthe controller at another serial port ( for example, com5 where
IOaddress is 4F8,IRQis 4), it need toredirectthe system environment variable by
SET TKT1 = 4F8 4
before launch TPANEL.EXE in the AUTOEXEC.BAT
TouchKit for DOSVersion 1.00.02.0904
TestTKT1...no panel found
TestTKT2...no panel found
TestPS2...Loopback OK
Read settings from PS2...OK
Driverinstalled

TouchKitTouch Panelv3.1.4 7
TouchKit for DOS also supportsthreeSoundModes: NONE,UPand DOWN.
Please go to C:\TouchKit\> tpanel.ini tochange the sound mode.
<tpanel.ini >
Beep=None 1322
〔promptBegin〕
TouchKit for DOSVersion 1.00.02.0904
〔promptEnd〕
After saving new tpanel.ini,user can force the driver to reload the new tpanel.ini by
executing C:\TouchKit\>tpanel -r Other adjustmentcan be checked by
C:\TouchKit\> tpanel-?
There are three utilities: TPDRAW, TP4PCAL and TP25PCAL tocalibrate touch
panel. Theyallsupport extra command-line arguments such as -g 1024x768 behind
to specifyscreen resolution on action.
Resolutions supported: (use 640x480 bydefault)
320x200, 640x200,640x350, 640x480,800x600, 1024x768 and 1280x1024
<TPDRAW>
Test the drawing position related to the displayscreen on panel.
E.g. C:\>tpdrawtkt2
Tryto write ordrawon it to verifythe touch position.
Press <ESC> button to exit.
Beep =none|down|up [frequency]
none:no sound; keep silent
down: beep when you touch down
up:beep when you touch up

TouchKitTouch Panelv3.1.4 8
<TP4PCAL>
Correct 4point locations on screen withthe panel.
E.g. C:\>tp4pcaltkt2
Touch the blinking symbol on paneluntil beep orstop blinking.
<TP25PCAL>
Correct 25 point locations on screen with the panel.
E.g. C:\>tp25pcaltkt2
Touch the blinking symbol on paneluntil beep orstop blinking.
After the calibration, the newrecord will overwrite the old one.

TouchKitTouch Panelv3.1.4 9
Right Button Emulator supports onlyvideomode 3and muststart after the driver
being installed; user mayedit C:\>AUTOEXEC.BAT to toggleiton/off. Ifit isturned
on abutton willappearin the right-bottom corner ofscreen when mousepointer is
turned on.
The labelof button, which is [L] bydefault andbecomes [R] after button being
clicked, indicates that next touching downon panel will be reported as left (orright)
mouse button click.
L