Ikelite iTTL User manual

• The Ikelite iTTL Adapter is for use with Non-Ikelite housings with
a TTL hot-shoe & Ikelite-style bulkhead.
(
hot-shoe must have all 5 wires onne ted )
Refer to housing spe ifi ations or onta t housing manufa turer for
onne tor style and wiring information.
• The Adapter offers both TTL and Manual operation.
Exposure ompensation is not provided through the Adapter,
but an be a essed via the amera’s menus.
• The Ikelite iTTL Adapter is ompatible with the following Digital
Cameras; Nikon D-40, D-50, D-70, D-70s,
D80, D-200 and Fuji S5 Pro.
• The Ikelite iTTL Adapter is Not ompatible with the following
Nikon Cameras; D-100, D-1X, D-2X, D-2H.
CCoonnnneettiinngg AAddaapptteerr ttoo hhoouuiinngg________________________________________________
• Make sure all omponents are dry.
• Clean and lightly lubri ate the o-ring on the male Ikelite onne tor.
Che k o-ring for ra ks or ni ks.
• Lightly lubri ate the threads on the housing bulkhead.
• Note the positioning of the re epta les and pins. Properly align the
end of the syn ord and insert it into the housing bulkhead.
• Hand tighten the knurled ring on the syn ord until there is no
in-out movement between syn ord onne tor and housing bulkhead.
CCoonnnneettiinngg DDSS SSuubbssttrroobbeess____________________________________________________
Use ONLY with Ikelite DS Substrobes. DS50/51, DS125, DS200
(
see strobe ompatibility hart on reverse side )
• Make sure all omponents are dry.
• Remove the waterproof ap from the Ikelite bulkhead on the bla k
delrin pod.
• Clean and lightly lubri ate the o-ring on the male Ikelite onne tor.
Che k o-ring for ra ks or ni ks.
• Lightly lubri ate the threads on the adapter bulkhead.
• Note the positioning of the re epta les and pins. Properly align the
end of the syn ord onne tor and insert it into the adapter’s bulkhead.
• HHoolldd tthhee aaddaapptteerr’’ss kknnuurrlleedd rriinngg wwhheenn ttiigghhtteenniinngg tthhee ssyynn oorrdd..
• Hand tighten the knurled ring on the syn ord until there is no
in-out movement between syn ord onne tor and adapter bulkhead.
Single or Dual Ikelite syn ords an be atta hed.
Dual strobe use requires dual syn ord.
Two strobes annot be operated by independent adapters.
Instru tions ontinued on reverse side
• The Ikelite iTTL Adapter is for use with Non-Ikelite housings with
a TTL hot-shoe & Ikelite-style bulkhead.
(
hot-shoe must have all 5 wires onne ted )
Refer to housing spe ifi ations or onta t housing manufa turer for
onne tor style and wiring information.
• The Adapter offers both TTL and Manual operation.
Exposure ompensation is not provided through the Adapter,
but an be a essed via the amera’s menus.
• The Ikelite iTTL Adapter is ompatible with the following Digital
Cameras; Nikon D-40, D-50, D-70, D-70s,
D80, D-200 and Fuji S5 Pro.
• The Ikelite iTTL Adapter is Not ompatible with the following
Nikon Cameras; D-100, D-1X, D-2X, D-2H.
CCoonnnneettiinngg AAddaapptteerr ttoo hhoouuiinngg________________________________________________
• Make sure all omponents are dry.
• Clean and lightly lubri ate the o-ring on the male Ikelite onne tor.
Che k o-ring for ra ks or ni ks.
• Lightly lubri ate the threads on the housing bulkhead.
• Note the positioning of the re epta les and pins. Properly align the
end of the syn ord and insert it into the housing bulkhead.
• Hand tighten the knurled ring on the syn ord until there is no
in-out movement between syn ord onne tor and housing bulkhead.
CCoonnnneettiinngg DDSS SSuubbssttrroobbeess____________________________________________________
Use ONLY with Ikelite DS Substrobes. DS50/51, DS125, DS200
(
see strobe ompatibility hart on reverse side )
• Make sure all omponents are dry.
• Remove the waterproof ap from the Ikelite bulkhead on the bla k
delrin pod.
• Clean and lightly lubri ate the o-ring on the male Ikelite onne tor.
Che k o-ring for ra ks or ni ks.
• Lightly lubri ate the threads on the adapter bulkhead.
• Note the positioning of the re epta les and pins. Properly align the
end of the syn ord onne tor and insert it into the adapter’s bulkhead.
• HHoolldd tthhee aaddaapptteerr’’ss kknnuurrlleedd rriinngg wwhheenn ttiigghhtteenniinngg tthhee ssyynn oorrdd..
• Hand tighten the knurled ring on the syn ord until there is no
in-out movement between syn ord onne tor and adapter bulkhead.
Single or Dual Ikelite syn ords an be atta hed.
Dual strobe use requires dual syn ord.
Two strobes annot be operated by independent adapters.
Instru tions ontinued on reverse side
Ikelite iTTL Adapter
instruction manual
#4301 for Specified Nikon & Fuji Digi al SLR Cameras
in Non-Ikeli e Housings
Ikelite iTTL Adapter
Ikelite Connector
Ikelite Waterproof Cap
Delrin Po d
O-ring
Knurled Ring
(Rotate)
Ikelite
Bulkhead
Ikelite iTTL Adapter
instruction manual
#4301 for Specified Nikon & Fuji Digi al SLR Cameras
in Non-Ikeli e Housings
Ikelite iTTL Adapter
Ikelite Connector
Ikelite Waterproof Cap
Delrin Po d
O-ring
Knurled Ring
(Rotate)
Ikelite
Bulkhead

IIkkeelliittee LLiimmiitteedd WWaarrrraannttyy
All Ikelite produ ts are warranted against any manufa turing defe ts for a
period of one (1) year from the date of pur hase. Defe tive produ ts
should be returned prepaid to Ikelite. Ikelite will, at its dis retion, repair or
repla e su h produ ts, and return to ustomer prepaid. All other laims, of
any nature, in luding but not limited to bulb failure are not overed.
Ex ept as mentioned above, no other warranty expressed or implied,
applies to this Ikelite produ t.
RReettuurrnniinngg PPrroodduuttss ffoorr SSeerrvviiee
Ikelite is most interested in performing any servi e to assure that all
produ ts perform as intended. For repair or servi e, return the produ t
to the address below with your name, address, phone number and a
brief des ription of the problem. Eviden e of pur hase date must be
provided to obtain warranty servi e.
IIkkeelliittee UUnnddeerrwwaatteerr SSyysstteemmss
5500 WW 3333rrdd SSttrreeeett
IInnddiiaannaappoolliiss,, IINN 4466220088 UUSSAA
331177--992233--44552233
eemmaaiill:: iikkeelliittee@@iikkeelliittee..oomm
wwwwww..iikkeelliittee..oomm
44330011--0011--00440077
DDSS--5500 SSuubbssttrroobbeess
• Substrobes with Serial Number below 63,850 an Not
be updated to operate orre tly with the latest TTL
onversion ir uitry.
• Substrobes with Serial Number between 63,850 and
69,999 require a $100 update to operate with the latest
TTL onversion ir uitry.
SSTTRROOBBEE CCOOMMPPAATTIIBBIILLIITTYY CCHHAARRTT
DDSS--112255 SSuubbssttrroobbeess
• Substrobes with Serial Number below 2,500 an Not
be updated to operate orre tly with the latest TTL
onversion ir uitry.
• Substrobes with Serial Number between 2,500 and 4,999
require a $100 update to operate with the latest TTL
onversion ir uitry.
S
Sw wi it t h hi in ng g b be et tw we ee en n T TT TL L a an nd d M Ma an nu ua al l_ __ __ __ __ __ __ __ __ __ __ __ __ _
• The knurled ring on the iTTL Adapter’s bla k delrin pod has a
white dot.
• The knurled ring an be rotated lo kwise or ounter- lo kwise to
align the knurled ring’s white dot with the white dot on the label next
to TTL or Manual.
• TThhee DDSS SSuubbssttrroobbee mmuusstt bbee sseett ttoo TTTTLL mmooddee ffoorr tthhee iiTTTTLL aaddaapptteerr ttoo
pprroovviiddee TTTTLL ooppeerraattiioonn..
IIkkeelliittee LLiimmiitteedd WWaarrrraannttyy
All Ikelite produ ts are warranted against any manufa turing defe ts for a
period of one (1) year from the date of pur hase. Defe tive produ ts
should be returned prepaid to Ikelite. Ikelite will, at its dis retion, repair or
repla e su h produ ts, and return to ustomer prepaid. All other laims, of
any nature, in luding but not limited to bulb failure are not overed.
Ex ept as mentioned above, no other warranty expressed or implied,
applies to this Ikelite produ t.
RReettuurrnniinngg PPrroodduuttss ffoorr SSeerrvviiee
Ikelite is most interested in performing any servi e to assure that all
produ ts perform as intended. For repair or servi e, return the produ t
to the address below with your name, address, phone number and a
brief des ription of the problem. Eviden e of pur hase date must be
provided to obtain warranty servi e.
IIkkeelliittee UUnnddeerrwwaatteerr SSyysstteemmss
5500 WW 3333rrdd SSttrreeeett
IInnddiiaannaappoolliiss,, IINN 4466220088 UUSSAA
331177--992233--44552233
eemmaaiill:: iikkeelliittee@@iikkeelliittee..oomm
wwwwww..iikkeelliittee..oomm
44330011--0011--00440077
DDSS--5500 SSuubbssttrroobbeess
• Substrobes with Serial Number below 63,850 an Not
be updated to operate orre tly with the latest TTL
onversion ir uitry.
• Substrobes with Serial Number between 63,850 and
69,999 require a $100 update to operate with the latest
TTL onversion ir uitry.
SSTTRROOBBEE CCOOMMPPAATTIIBBIILLIITTYY CCHHAARRTT
DDSS--112255 SSuubbssttrroobbeess
• Substrobes with Serial Number below 2,500 an Not
be updated to operate orre tly with the latest TTL
onversion ir uitry.
• Substrobes with Serial Number between 2,500 and 4,999
require a $100 update to operate with the latest TTL
onversion ir uitry.
S
Sw wi it t h hi in ng g b be et tw we ee en n T TT TL L a an nd d M Ma an nu ua al l_ __ __ __ __ __ __ __ __ __ __ __ __ _
• The knurled ring on the iTTL Adapter’s bla k delrin pod has a
white dot.
• The knurled ring an be rotated lo kwise or ounter- lo kwise to
align the knurled ring’s white dot with the white dot on the label next
to TTL or Manual.
• TThhee DDSS SSuubbssttrroobbee mmuusstt bbee sseett ttoo TTTTLL mmooddee ffoorr tthhee iiTTTTLL aaddaapptteerr ttoo
pprroovviiddee TTTTLL ooppeerraattiioonn..