ikonic Patio Bolt User manual

3mm,
4mm &
10mm
Drill Bits
Pencil
Phillips
Head
Screw
Driver
Hole
Punch
Flat
Head
Screw
Driver
Optional:
Instructions to install the Patio Bolt.
Note: Will fit Aluminium and Timber doors of following style: Patio, Sliding and Hinged. Contents
If you are replacing an existing bolt, remove existing bolt, clean down surfaces and follow the installation process.
Patio Bolt
Very Important!
Please fasten all screws by hand and not an electric screw driver or drill, as over tightening is not recommended.
Drill Gloves Safety
Goggles
Patio Bolt x 2 Keeper x 2
Security Screws x 4
Phillips Head Screws x 4
If using one-
way screws.
Step 3: Bolt
Option 1: The bolt of the patio lock fully engages the door frame.
If the bolt of the patio lock fully engages the door
frame, make sure the door is properly closed and
tap the end of the bolt against the frame to mark
the drilling position. Using a hole punch or a nail,
punch the centre of the holes before drilling to
make sure drill bit does not move.
Drill a 10mm hole for the bolt. Make sure it is
deep enough for the bolt to fully engage. If you are
wanting to have a fixed venting position, move the
door to the desired position and drill another 10mm
hole using the same process.
Check to make sure the lock works in the
closed and vented position. If the lock works
to satisfaction, the phillips head screws can be
replaced with the security screws (B) provided.
(Note: The security screws (B) cannot be removed
once installed.)
marked
position
10mm
B
Step 1: Preparation Step 2: Installing the Patio Bolt to door
Hold Patio Bolt in desired position
and mark the centre of the 2 x
installation holes. Using a hole
punch or a nail, punch the centre
of the holes before drilling to
make sure drill bit does not move.
Drill 2 x 4mm holes at the marked
positions. Install the Patio Bolt to
the door using the appropriate
screw type (Timber or Metal
thread) for the type of door.
Note: If installing to a glass door, make sure that the screws will clear the glass
line. Also check that the Patio Bolt will not interfere with the door frame in the
closed or open position.
Determine the type of door
you will be installing to.
Make sure you choose the
best fixing location for your
door. The Patio Bolt can be
fitted to the rear or face of
a sliding door and the face
of an inward opening door
with keeper provided.
Try to avoid fitting the Patio
Bolt at the bottom of a door
as the hole might penetrate
the sill and this may allow water to enter. Accuracy is vital, so mark and measure
carefully and drill holes level.
GLASS LINE
4mm
Page 1
Installation Tools Required:
01384-001_IKONIC PATIO BOLT - LEAFLET 697210, 697220, 697230, 697240.indd 1 15/10/2014 9:57 am

WARRANTY CONDITIONS
Any claim under this warranty must be made within 3 years of the date of purchase of the product. To make a claim under the warranty, take the product (with proof of purchase) to any Bunnings store (see www.bunnings.com.au for store locations). Romak
Hardware Distributors Pty Ltd bears reasonable, direct, expenses of claiming under the warranty. You may submit details and proof to our store for consideration. The warranty covers manufacturer defects in materials, workmanship and finish under normal
use. This warranty is provided in addition to other rights and remedies you may have under law: our goods come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement or refund for a major failure and
compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The warranty excludes damage resulting
from product misuse or product neglect. The warranty covers domestic use only and does not apply to commercial applications. This warranty is given by Romak Hardware Distributors Pty Ltd, ABN 15489950457, 177-181 Atlantic Drive, Keysborough Vic 3173,
[phone], e-mail: [email protected] Suits models 697210, 697220, 697230, 697240.
01384
Option 2: The bolt of the patio lock does not fully engage the door frame.
If the bolt of the patio lock does not engage the
door frame, use the keeper provided. With the door
properly closed, slide the keeper over the lock bolt.
Hold the keeper against the door frame and mark the
fixing holes.
Security screws:
If the lock works to satisfaction, the phillips
head screws can be replaced with the security
screws (B) provided, using a large flat head
screw driver.
(Note: The security screws (B) cannot be
removed once installed.)
Drill 2 x 3mm holes at the marked location and
install the keeper into place using the phillips head
screws provided. Check to make sure the lock
works in the closed position.
Page 2
Patio Bolt
01384-001_IKONIC PATIO BOLT - LEAFLET 697210, 697220, 697230, 697240.indd 2 15/10/2014 9:57 am