Image Dynamics USA ID Series User manual

ID65cs
Please read through this manual to familiarize yourself with your new amplifier. Should your Image Dynamics
mobile amplifier ever require service, you will need to have the original dated receipt.
OWNERS MANUAL
ID SERIES COMPONENT SYSTEM

2-WAY COMPONENT SYSTEM
Congratulations on your purchase of Image Dynamics speakers. You now own a speaker
of uncompromising design and engineering from a factory that truly believes in the
relentless pursuit of perfection. Incorporating the highest quality parts and state-of-
the-art materials, these speakers display the ultimate balance between high fidelity,
performance and long-lasting reliability.
TECHNICAL FEATURES
Premium Component System offers a level of performance to please even the most
critical listener
Parabolic Butyl Rubber Surround to ensure long lasting and linear piston movement for
dynamic sonic reproduction
Poly/Mica Cone for detailed and distortion free mid-bass and vocal reproduction
Y-35 Magnet Motor Structure provides a very powerful flux field to increase efficiency
25mm Silk Dome Tweeter coated with our proprietary DDC coating for accurate sonic
delivery all the way up to 25kHz
High Grade Crossover Components including metalized polypropylene capacitors and
low loss 16 gauge air core inductors
3
∆Caution ∆
High powered audio systems in a vehicle are capable of generating
higher than “Live Concert” levels of sound pressure. Continued ex-
posure to excessively high volume sound levels could cause hearing
loss or damage. Also, operation of a motor vehicle while listening to
audio equipment at high volume levels may impair your ability to hear
external sounds such as horns, warning signals, or emergency vehicles—
thus creating a potential traffic hazard. In the interest of safety,
Image Dynamics USA highly recommends listening at lower volume levels
when driving.

Woofer
SPECIFICATIONS for Image Dynamics ID65cs Driver
(Due to Constant Improvements, Specifications and Parameters are subject to change without notice.)
Model Size Nominal
Impedance
Frequency
Response
Sensitivity
1W/1M
Magnet
Size
Mounting
Depth
Power RMS/Peak
ID65cs 6.5” 4-ohm 55Hz-25kHz 89 dB 21oz. 2.75”
(70mm)
100W/200W
Before beginning your installation, thoroughly read this guide and keep it as a reference.
It will give you tips on proper placement, wiring, and installation as well as how to obtain
the best sound from the Image Dynamics speakers you have selected.
INSTALLATION EXPERIENCE
Installation of Image Dynamics Speakers requires experience with a variety of mechanical
and electrical procedures. This manual only provides general installation and operation
instructions. If you have any reservations about your installation skills or lack of the proper
tools, please contact your local Image Dynamics dealer for assistance.
SPECIFICATIONS for Image Dynamics ID65cs Tweeter
Dome
Size
Mounting
(Diameter)
Nominal
Impedance
Frequency
Response
Sensitivity
(1M / 1M)
Mounting
(Depth)
Power
(RMS/Peak)
1” Silk 1 7/8” (48mm) 4Ω3K-25Khz 89 dB 3/4” 50 / 100mm
Crossover Network
Tweeter

TIPS TO GET THE MOST OUT OF YOUR
Image Dynamics SYSTEM
Your Image Dynamics speakers have been meticulously engineered and designed to han-
dle high power musical reproduction. Despite their rugged construction, it is possible to
damage your speaker if they are improperly used. In general, you will hear distortion as
a so-called warning before any damage occurs. If you hear distortion in your system, im-
mediately reduce the musical level to the point where the sound retains its clarity.
1. Be sure you supply the speakers with enough unclipped amplifier power to drive them
properly. (More damage can be done to a speaker by under-powering and clipping your
amplifier than any other way!)
2. Where possible, a separate amplifier just for your speaker should be used with an elec-
tronic crossover to set the frequency range. One amplifier with passive crossovers will
work (Tri-Way Setup), but the system will do more with less stress on the amplifier by
using two amps.
3. To avoid any possible sound cancellation from the front of the speaker to that of the rear
of the speaker, cut a panel of Masonite or MDF to firmly mount the speaker if the vehicle’s
original cutout is too big.
4. When connecting speaker wires from the amplifier or head unit to that of the speaker
itself, pay attention to the polarity of the connection. This will insure optimum sound re-
production and performance.
5. For maximum dynamic performance use weather stripping to insure a tight seal.
6. Do not mount any speakers or external crossovers where they will get wet.
7. Remember the Golden Rule “Measure twice…cut once.”
PREPARING FOR INSTALLATION
NOTE: The tools listed below may be required for proper installation.
• An electric drill with drill bits
• Phillips-head and standard screwdrivers
• Wire strippers
• Crimping tool and needle-nose pliers
• Silicone sealant or closed cell weather-stripping
• Metal le
• Hole saw
• Electronic (rosen not acid cove) solder
5

INSTALLATION PRECAUTIONS
NOTE: Proceed only if you are a qualified installer otherwise; let your
dealer do it.
• Always wear protective eyewear when using tools.
• Turn off all stereo and other electrical devices before you begin.
• Disconnect the (-) negative lead from your vehicle’s battery.
• Keep the speakers in the package until nal installation.
• Locate all fuel lines, brake lines, oil lines, and electrical cables when planning
your installation.
• Check to see if there is enough clearance behind the mounting surface before
installing the speakers.
• When running speaker wires through sheet metal, be sure to use grommets to
properly insulate the wires from metal edges.
INSTALLATION PROCEDURES
• Since these speakers utilize a unique low prole tweeter housing that has minimal
tweeter protrusion, original factory mounting cutouts can still be used with the factory
grills in many cases.
• These Image Dynamics speakers can be used above or below the mounting hole.
Typically, your vehicle factory’s speaker cutouts will accommodate these new speakers
without any modifications. When the speaker has been correctly installed, there should
be no air leaks between the front and back of the speaker.
• For door installations, check the clearance of the windows throughout the entire range
of the window’s travel.
• Mount your speakers securely! If the speaker has four or more mounting holes, it is best
to use all of them.
• Check the available mounting depth before installing the speaker. Use care when
removing factory grills, door panels and factory speakers.

COMPONENT SYSTEM INSTALLATION
Component Woofer
The proper installation procedure for mounting these high performance mid-range speak-
ers is to secure the speaker to the vehicle’s speaker mounting hole. Once the speaker is in
place, determine if the supplied grill needs to be installed. If so, place the grill in place over
the speaker and screw the speaker into the mounting hole.
Component Tweeter
These high quality tweeters come complete with several mounting housings for instal-
lation versatility. Once you have chosen the housing that is to be used, gently press the
tweeter into the proper mounting cup. Experiment with the tweeter positioned in several
locations to determine the best imaging result before cutting out any panel. Typically
tweeters should be mounted on axis and as close to ear level as possible. If the tweeter has
to be removed from the mounting cup, insert a small screwdriver in the back of the tweeter
and carefully push the tweeter from the mounting cup.
7

INSTALLATION PROCEDURES
By mounting the tweeter separately from the woofer (or mid-range driver) the installer
can choose the best location for sound quality and imaging. Three mounting types are
possible allowing more versatility for the tweeter location. These are flush mount, surface
mount, and angle mount.
Flush Mounting (Type A)
The best location for the tweeter is usually high up on the door and as far forward as pos-
sible without interference from the dashboard. If the desired location is flat and space
behind the door panel allows the use of the flush mount housing, follow the drawing as
shown below:
After checking for clearance, cut the mounting hole in the door panel (see Tweeter Speci-
fications for hole size). Mount the Flat Base from the outside with the mounting clip on
the inside of the door panel. Secure the mounting clip to the Flat Base with the long silver
screw provided.
Surface/Angle Mounting (Type B and C)
If mounting the tweeter on the surface works out best, refer to the following drawing to
see how to best mount the tweeter. Black sheet metal screws have been provided to attach
the surface base to the door panel.

COMPONENT TWEETERS
These high quality tweeters come complete with several mounting housings for installa-
tion versatility. Typically tweeters should be mounted on axis and as close to ear level as
possible. After you have chosen the housing to be used, gently press the tweeter in the
proper mounting base. Once the tweeter base is mounted, push and “twist” the housing
until it locks to the base. Below are exploded views showing the possible types of tweeter
mounting.
9

CROSSOVER NETWORK INSTALLATION AND WIRING
Your Image Dynamics Component system contains two separate 2-way crossover net-
works. When choosing a location to mount the crossovers, keep in mind they contain
electronic parts which can be damaged by moisture and dirt.
Correct wiring of the crossover is critical to avoid damage to the speakers and ensure true
high fidelity sound. Pay close attention to the markings on the crossover to be certain the
correct speakers are in the correct outlets as follows:
1) Connect the ampli er or head unit output to the crossover’s INPUT terminals.
2) Connect the terminals labeled WOOFER to the component midrange speaker.
3) Connect the terminals labeled TWEETER to the component tweeter set.
CAUTION: Care must be taken when adjusting the screws on the input
terminals that fasten the speaker wires to the crossover network. Make
sure each connection is secure without over tightening. Use of power
tools to tighten these screws is not recommended as they can strip the
screws and permanently damage the input terminals.
NOTE: BE SURE TO OBSERVE PROPER POLARITY WHEN CONNECTING SPEAKER WIRES
TO THE CROSSOVER NETWORK TERMINALS.
This manual is the exclusive property of Image Dynamics USA, Inc. Any reproduction of this manual, or use other than its intentions is strictly prohibited
without the express consent of Image Dynamics USA, Inc. Copyright 2016 Image Dynamics USA, Inc.

Image Dynamics
LIMITED WARRANTY POLICY
Image Dynamics USA, Inc. offers limited warranty on Image Dynamics products under normal use on
the following terms:
Image Dynamics Speakers are to be free of defects in material and workmanship for a period of one
(1) year.
This warranty applies only to Image Dynamics products sold to consumers by Authorized Image Dy-
namics Dealers in the United States of America. Products purchased by consumers from a Image
Dynamics dealer in another country are covered only by that country’s Distributor and not by Image
Dynamics USA.
This warranty covers only the original purchaser of Image Dynamics product. In order to receive ser-
vice, the purchaser must provide Image Dynamics with the receipt stating the consumer name, dealer,
product and date of purchase.
Products found to be defective during the warranty period will be repaired or replaced (with a product
deemed to be equivalent) at Image Dynamics’s discretion and will not be liable for incidental or con-
sequential damages. Image Dynamics will not warranty this product under the following situations:
•Speakersreceivedwithbentframesorwaterdamage
•Abusesuchasholesinthecone,surroundorrippedspider
•Voicecoildamageduetoamplierclippingordistortion
•Productthathasnotbeeninstalledaccordingtothisownersmanual
Any implied warranties including warranties of tness for use and merchantability are limited in dura-
tion to the period of the express warranty set forth above. Some states do not allow limitations on the
length of an implied warranty, so this limitation may not apply. No person is authorized to assume for
Image Dynamics any other liability in connection with the sale of this product.
Please call [phone] for Image Dynamics Customer Service. You must obtain an RA# (Return Au-
thorization Number) to return any product to Image Dynamics. The RA number must be prominently
marked on the outside of the shipping carton or the delivery will be refused. Please pack your return
carefully; we are not responsible for items damaged in shipping. Return the defective product along
with a copy of the original dated retail sales receipt, plus $12.00 for handling and diagnostic evalua-
tion to:
ImageDynamicsUSA,Inc.,
Attn:Returns(RA#__________)
2133S.GreenPrivadoOntario,CA91761
Residents of HI, AK and US territories will be charged for return shipping. All inquires regarding ser-
vice and warranty should be sent to the above address.
Removed or altered serial numbers will void this warranty
11

Image Dynamics USA
2133 S. Green Privado – Ontario, CA 91761
Tel. [phone] – Fax [phone]
www.imagedynamicsusa.net