Impecca IWA06-QS20 User manual

Portable Air Conditioner—User Manual
Aire acondicionado—Manual de usuario
Models: IWA06-QS20/ IWA08-QS20
www.impecca.com

Read the following notices and information carefully to ensure proper operation of your air
conditioner unit.
This manual is solely provided for informational purposes and in no way constitutes a legally
binding document between the manufacturer, distributor, and end consumer.
Lea las siguientes indicaciones cuidadosamente para asegurar el correcto funcionamiento
de su unidad de aire acondicionado.
Este manual se proporciona únicamente con fines informativos y de ninguna manera
constituye un documento jurídicamente vinculante entre el fabricante, distribuidor y
consumidor final.
Warning: To avoid permanent damage to
unit:
Ensure it is in the upright position for at least 24 hours
before powering on the first time.7KLVLVHVSHFLDOO\
LPSRUWDQWLIWKHXQLWZDVVKLSSHGWR\RXUORFDWLRQ
Advertencia: Para evitar daños
permanentes a la unidad:
Asegúrese de que está en la posición vertical durante al
menos 24 horas antes de encender la primera vez.
(VWRHVHVSHFLDOPHQWHLPSRUWDQWHVLODXQLGDGIXH
HQYLDGDDVXGRPLFLOLR

ENGLISHESPAÑOL
–1–
INTRODUCTION
Thank you for purchasing this quality Impecca in-window air conditioner unit. To ensure the
longest life and highest energy eiciency of your unit, please carefully follow these operating
instructions. Keep these instructions in a safe place and consult them as needed. Please note
that constant enhancement and improvements to our air conditioning units may mean that
your model will slightly dier in appearance from the model pictured in this manual, but the
actual operation and installation of the unit remains unchanged. This manual is solely provid-
ed for informational purposes and does not constitue a binding, legal contract.
SAFETY NOTICE:
This appliance should not be used by children or mentally/physically disabled persons with-
out strict, direct supervision by a responsible adult. Never play with or around the appliance.
SAFETY INFORMATION
• Before operation, ensure your electrical installation (outlets and circuits) complies
with the power specifications found on the unit.
• Before cleaning or maintaining the air conditioner, please turn o air conditioner
and unplug the unit.
• Make sure the power cord isn’t kinked, bent, or under the weight of sharp or heavy
objects.
• Do not pull or yank the power cord to unplug the unit or move the air conditioner.
• Do not insert or unplug the power plug with wet hands.
• Only use a grounded power outlet. Make sure the grounding is functional.
• If the power cord is damaged, it must be replaced by the manufacturer or a quali-
fied technician in order to avoid fire and electrical hazards.
• Should abnormal operation occur (such as a burning smell), please disconnect
power cord immediately and contact your local dealer.
• If nobody is present to monitor the operation of the unit, please turn it o and
disconnect the power cord.
• Do not splash or pour water on air conditioner to avoid causing a short circuit or
damage to the unit.
• Do not put or hang dripping objects above the air conditioner.
• Ensure the ambient temperature remails well above freezing (32° or 0°) to avoid
cracking or damaging the unit.
• Keep heat sources away from the air conditioner.
• Ensure the unit is far away from fire, inflammable, or explosive objects.
• Never allow children or persons with reduced physical, sensory, or mental capabil-
ities to operate or play around the air conditioner without direct adult supervision.
• Never allow children to perform cleaning or other user-maintenance operations
without direct adult supervision.
• Never attempt to repair or disassemble the air conditioner by yourself.
• Never insert objects into the air conditioner.

ENGLISH ESPAÑOL
–2–
OPERATING CONDITIONS
• The air conditioner must be operated within the temperature range of 62°F to 95°F
(16°C to 35°C).
• A perimiter of 12′′(30cm) around the air conditioner should be free of all objets.
• Do not operate the air conditioner in humid environments.
• Please keep air inlet and air outlet clean and free of obstructing objects.
• During operation, close doors and windows to improve cooling eect.
• Please put the air conditioner at smooth and flat ground for operation to avoid
noise and vibration.
• Do not tilt or turn over the air conditioner. If there’s problem, please disconnect
the power supply immediately and contact your local dealer or technical support.
GETTING TO KNOW YOUR AIR CONDITIONER
1
2
3
4
5
1. Cool air outlet
2. Cool air directional blades
3. Warm air intake
4. Power cord
5. Control Panel

ENGLISHESPAÑOL
–3–
USING YOUR AIR CONDITIONER
CONTROL PANEL OVERVIEW
h
g
f
e
i
a
b
c
d
PRIMARY FUNCTIONS
1. Power ON/OFF button: Use this button to turn the unit on or o.
2. Mode button: Cycle between cooling mode, dehumidifier mode, and fan mode.
3. Fan button
4. Reset filter button
5. Delay/timer button
6. Temperature +/- buttons: Set the desired room temperature by pressing the ap-
propriate button. Temperature changes are displayed in 1° increments in the
range of 61°F (16°C) and 86°F (30°C) Note: Temperature can not be set when using
the fan or dehumidifier modes
7. Temperature LED: Displays the desired room temperature during cooling mode. In
other modes, the display will be blank.
INDICATORS (WHEN ILLUMINATED)
a. Auto fan speed
b. High fan speed
c. Medium fan speed
d. Low fan speed
e. Cooling mode
f. Fan only mode
g. Energy saver mode
h. Clean/replace filter
i. Timer activated

ENGLISH ESPAÑOL
–4–
REMOTE CONTROL
1. ON/OFF button
2. Fan +/- buttons
3. Temperature ▲/▼ buttons
4. Mode button
5. Auto button
6. Timer +/- buttons
7. Timer (DELAY) button
USING THE REMOTE CONTROL
ON/OFF BUTTON
Press the ON/OFF button to turn the unit on or o.
FAN +/- BUTTONS
Press the respective button to increase (+) or decrease (-) fan speed. For an automatic
selection appropriate fan speed based on ambient temperature and most eicient unit
operation, press the AUTO button.
TEMPERATURE ▲/ ▼ BUTTONS
Set the desired room temperature by pressing the appropriate button. Temperature
changes are displayed in 1° increments in the range of 61°F (16°C) and 86°F (30°C)
Note: Temperature can not be set when using the fan or dehumidifier modes
MODE BUTTON
Cycle between cooling mode, fan mode, and energy saver mode.
AUTO BUTTON
Press this button to have the unit automatically select appropriate fan speed based on
ambient temperature and most eicient unit operation.

ENGLISHESPAÑOL
–5–
TIMER (DELAY) BUTTON
• When the unit is running, press this button to program a time when the unit will
automatically turn o. Use the +/- buttons to change the air conditioners display
to determine the delay (in hours) until the unit will shut down in 1 hour incre-
ments. Press the DELAY button again to confirm the shut down command.
• If the unit is o and you want it to turn on in a certain amount of time, program it
in the same way as above.
• To cancel a timer, press the DELAY button to see remaining time before the timer
activates. Press the DELAY button again to cancel the timer.
Note: Timers can be set between the range of 1 - 24 hours. The unit must remain plugged in
for the timer to function properly.
REMOTE CONTROL LOCK
1. Press and hold the + and - buttons simultaneously to activate the remote control
child lock and prevent inadvertent changes to unit settings.
2. Press the + and - buttons simultaneously to deactivate the remote control lock.
CHANGE TEMPERATURE UNITS (C° OR F°)
1. While the unit is o, press the - and MODE button simultaneously to change the
unit readout temperature between Celsius (C°) and Fahrenheit (F°).
REPLACING THE REMOTE CONTROL UNIT BATTERIES
1. Press gently on the tab located on the back side of the remote control unit. Li out
the battery compartment cover.
2. Replace the batteries with two AAA 1.5v batteries. Insert batteries while respecting
the polarity of the batteries (+ and - sides). Replace both batteries at the same
time; never insert an old battery with a fresh battery to avoid a battery leak.
3. Gently reinsert the battery compartment cover.
REMOTE CONTROL OPERATION NOTES
• When using the remote control, aim the controller directly at the air conditioning
units IR receiver located on the control panel.
• The remote control must have a clear line of sight to the control panel.
• Interference to remote control operation may occur in areas with fluorescent light-
ing or wireless telephones.
• When the remote control will remain unused for long periods of time, please re-
move the batteries.

ENGLISH ESPAÑOL
–6–
PRE-INSTALLATION INSTRUCTIONS
Gather the following tools and unit accessories before beginning your installation:
UNIT & ACCESSORIES
1. Air conditioning unit
2. Flexible window adapter set
3. Sealing strip (no adhesive)
4. Upper guide rail
5. Sealing strip (with adhesive)
6. Foam insert
7. Screws - Type A (x4)
8. Screws - Type B (x6)
9. Window security bracket
10. Remote control
11. Remote control batteries (2x AAA)
12. Users manual
A
7
1 2
3 4
5 6
9
B
8
10 1211
x4 x6
TOOLS
• Philips screwdriver
• Flat-head screwdriver
• Pencil
• Scissors
• Level
• Measuring tape
Note: Never use an underrated electrical cord or outlet!

ENGLISHESPAÑOL
–7–
WEATHER-PROOF WINDOW MODIFICATIONS
If you have weather proof windows, the exterior window frame will be slightly higher
than the window sill, which results in a slanted air conditioning unit that will not properly
drain. Perform these modifications to ensure proper operation of your unit. If you have a
standard window, skip this step.
1. Cut a 2” thick piece of wood to the length of the the interior window width.
2. Verify that the wood is level with or up to 0.5” (1cm) higher than the exterior weath-
erproof frame.
3. Fasten the wood with screws to the windows sill and proceed with mounting.
INSTALLING YOUR UNIT
STEP 1: MOUNTING THE UPPER GUIDE RAIL
1. Tear the backing o of the sealing strip (#1) with adhesive. Align the strip to the
base of the upper guide rail (#2).
2. Use four Type A screws to mount the upper guide rail to the unit case.
1
2
STEP 2: MOUNTING THE FLEXIBLE SCREEN
1. Slide the screens into the guide rails on the right and le side of the unit.
2. Gently press the upper and lower ends of the screen into the upper and lower
guide rails on the unit.
1
2

ENGLISH ESPAÑOL
–8–
STEP 3: SEALING STRIP ON WINDOW FRAME
1. Aix an adhesive sealing strip to the bottom of the window frame.
STEP 4: MOUNT THE UNIT HOUSING IN THE WINDOW FRAME
1. With the help of another person, center the unit on the windowsill. The lower
guide should be completely flush with the windowsill. Gently lower the window
until it holds the upper guide in place. Allow a slight downward angle (about 3-5°)
for draining condensation that forms during air conditioner operation
2. Extend the flexible window set to
the right and le edge of the win-
dow. Fasten the upper guide and
top corners of the flexible screen
to the window frame with screws.
Use the frame locks to attach the
bottom corners to the windowsill.

ENGLISHESPAÑOL
–9–
STEP 5: SECURING THE WINDOW
1. To keep the window from being unintentionally opened and risk damaging the
unit or injuring passerby, use one type C screw to fasten the security bracket to
the window. If your window frame is made of wood, fasten the bracket into the
window (Detail 1). If your window frame is plastic (PVC), fasten the bracket to the
side of the window frame (Detail 2)
1
2
STEP 6: INSULATING FOAM
1. Prevent warm or cold air from entering by the partially opened window by placing
the non-adhesive foam strip in between the window sash and the glass pane.

ENGLISH ESPAÑOL
–10–
CLEANING & MAINTENANCE
SAFETY WARNING
To avoid electric shock, fire, damage, or injury while performing maintenance on your unit:
• Always turn o and disconnect the air conditioner from electric power.
• Never submerge the unit in water or spray liquids directly on the unit.
• Never use solvents or other flammable or volatile liquids (examples: paint thinner,
acetone, gasoline, etc.) to clean the air conditioner.
PRE-COOLING SEASON UNIT CHECK
Before using your air conditioner in the warm summer months, always perform the fol-
lowing verifications to ensure reliable, eicient operation.
• Check the air inlets and outlets for any foreign objects (example: leaves, sticks,
small toys, etc.)
• Check that the electrical cord and socket are not damaged, bent, or fraying.
• Check the filter and clean if necessary.
• Check the batteries in the remote control and insert or replace them if needed.
• Check whether the connectors, heat exhaust duct, and window brackets are firmly
in place.
• Check the heat exhaust duct for any cracks, damage, or other signs of weakness.
POST-COOLING SEASON UNIT CHECK
Aer using your air conditioner in the warm summer months, always perform the follow-
ing verifications.
• Disconnect the unit electrical power.
• Clean the filter and unit casing.
• Remove dust and other objects on the unit.
• Discard any accumulated water inside the unit (see section about drainage)
• Check whether the connectors, heat exhaust duct, & window brackets are firmly in place.
LONG-TERM STORAGE
Should you place your unit in long-term storage, perform all of the post-season checks
listed above and perform the following additional steps:
• Wrap the electrical cord loosely around the unit.
• Cover the unit with a sheet or cloth to prevent dust buildup inside during storage.
DISPOSAL INFORMATION
• Most unit packaging materials are recyclable. Please dispose of them according to
local recycling guidelines.
• If you wish to discard the unit, contact your local authorities for specific appliance
disposal instructions. If the unit is functional and in good repair, but you wish to
dispose of it, consider donating it to a local charity.

ENGLISHESPAÑOL
–11–
CLEANING THE OUTER HOUSING AND INTAKE GRILLE
If dust has accumulated on the unit, use a so, dry dusting towel to wipe it o. If grease or
other harder to remove substances is on the unit, use a wrung-out cloth dampened with
warm, soapy water. Use a so brush to clean o the grille.
CLEANING THE FILTER
For energy eicient operation, your filter should be cleaned every three months. Units in
dusty environments may require more frequent filter cleaning.
• The front filter cover rests on a bottom hinge and swings down. Open by using
pulls on either side of the cover.
• Remove the filter by gently tugging on it.
• Use a vacuum cleaner or run cold water onto the filter to clean it. If the filter is par-
ticularly dirty (such as grease buildup), wash and gently scrub the filter in a bath of
warm soapy water. Let the filter completely dry in a shady place; exposing the filter
to direct sunlight can cause deformation.
• Aer the filter is clean and completely dry, re-insert the filter by pressing firmly
without forcing.
Note: To avoid deformation and fire risk, never dry the filter with a heat source, such as a
hair dryer, fireplace, or heater.
TROUBLESHOOTING
PROBLEM / POSSIBLE CAUSES
The air conditioner does not function at all
• Is the power cable properly inserted into a functioning, grounded outlet?
• Is there a power failure such as a blown fuse or tripped circuit breaker?
• Is the timer set to “TIMER ON” mode? Disable the timer to immediately start op-
erations.
• Is the internal collection tank or partition drain full/blocked and the FULL light
illuminated? Empty the tank.
• Is the ambient temperature lower than 61°F (16°C)? A safety device prevents the
unit from cooling the room to even lower temperatures.
Heating or cooling is insuicient
• Is the room temperature set properly?
• Is the air filter dirty?
• Are doors or windows open?
• Is the room directly exposed to sunlight or are other heat sources in the room?
• Are there a large number of people in the room?

ENGLISH ESPAÑOL
–12–
The air conditioner does not restart immediately aer turning it o.
• The unit can not be restarted for 3 minutes to allow the condenser to cool and
avoid risk of fire. Wait a few minutes before restarting the unit.
The air conditioner unit starts and stops frequently.
• Verify the rating of your electrical system and outlets. You may need a qualified
electrician to troubleshoot and upgrade your electrical circuits if your air condi-
tioner unit exceeds the rated capacity.
• Ensure the exhaust system is properly connected and not bent or kinked. Keep
the hose as short as possible and cut excess length as needed.
Fog is blown out during cooling
• In warm, high humidity environments this may naturally occur. Continued cool-
ing will remove excess humidity from the room and the fog will disappear.
The unit emits a strange smell
• This may be caused by cigarette smoke or other residues from cooking and other
living activities that remain in the air conditioning unit. Clean the filter.
The unit makes loud or unusual noises and vibrations
• Place the unit on a level surface.
There is a “squeezing” noise
• The cycling of the refrigerant inside the unit can temporarily cause this noise.
There is a “patting” noise
• This is oen caused by heat expansion in the plastic parts.
The remote control doesn’t work
• Ensure the remote control has a clear line-of-sight to the operating panel on the
unit and ensure the sensors are not obstructed by curtains or other objects. Ensure
the remote control has fresh, working batteries.
There is moisture at the air output
• High humidity environments may cause condensation at the air flow output.
Wipe the condensation o with a sponge.

ENGLISHESPAÑOL
–13–
IF ANY OF THE FOLLOWING PHENOMENA OCCUR DESPITE THE ABOVE TROUBLESHOOT-
ING TECHNIQUES, PLEASE TURN OFF THE UNIT AND DISCONNECT THE POWER CORD
IMMEDIATELY AND CONTACT TECHNICAL SUPPORT OR A QUALIFIED TECHNICIAN:
• The fuse blows or circuit breaker trips frequently.
• The power cable is abnormally hot.
• The insulation of the power cable is ripped, shred or torn.
• The unit controls do not work.
• The unit produces abnormal noises.
UNIT ERROR CODES
When the air conditioner status is abnormal, the indicator display on the indoor unit will dis-
play an appropriate error code. Refer to the below table for specific and immediate action.
E5: OVER-CURRENT PROTECTION
Unplug and restart your unit to clear the error. If the error persists, contact a qualified
service technician.
E6: Unplug and restart your unit to clear the error. If the error persists, contact a qualified
service technician.
F1: Unit failure. Contact a qualified service technician.
F2: Unit failure. Contact a qualified service technician.
H1: Defrosting status; a natural phenomenon. The error will automatically clear aer suf-
ficiently defrosting the cooling coils.
H6: Unplug and restart your unit to clear the error. If the error persists, contact a qualified
service technician.
OTHER ERROR CODES: Contact a qualified service technician.
TECHNICAL SUPPORT
For additional assistance, please visit our website or contact technical support.
Web: www.impecca.com
Phone: [phone]
Email: [e-mail]

ENGLISH ESPAÑOL
–14–
INTRODUCCIÓN
Gracias por comprar esta unidad de aire acondicionado para ventana de calidad Impecca.
Para asegurar una larga vida útil y la más alta eficiencia de energía de su unidad, siga cuidado-
samente estas instrucciones. Mantenga estas instrucciones en un lugar seguro y consúltelas
cuando lo requiera. Tome en cuenta que las mejoras constantes a nuestras unidades de aire
acondicionado significan que su modelo puede variar ligeramente en apariencia al comparar-
lo con el modelo en la imagen, pero la operación actual y el proceso de instalación permane-
cen sin cambios. Este manual se proporciona únicamente con fines informativos y de ninguna
manera constituye un documento legal vinculante.
AVISO DE SEGURIDAD:
Este electrodoméstico no debe ser utilizado por niños o por personas que tienen una disca-
pacidad mental o física sin la supervisión estricta y directa de un adulto responsable. Nunca
juegue con o cerca de la unidad.
INFORMACIÓN DE SEGURIDAD
• Antes de la operación, asegúrese que su instalación eléctrica (tomacorrientes y
circuitos) cumplan con las especificaciones de energía y potencia señaladas en
la unidad
• Antes de limpiar o darle mantenimiento a la unidad de aire acondicionado, apá-
guelo y desconéctelo
• Asegúrese que el cable de suministro de energía no esté torcido, doblado, u opri-
mido bajo objetos pesados o filosos.
• Para desconectar la unidad o moverla de lugar no jale el cable de suministro de
energía.
• No conecte o desconecte la unidad con las manos mojadas.
• Utilice solamente un tomacorrientes aterrizado. Asegúrese que la conexión a tie-
rra es la adecuada y funciona.
• Si el cable de suministro de energía está dañado, debe ser reemplazado por el
fabricante o por un técnico calificado para evitar incendios y peligros eléctricos.
• En caso de que ocurra una operación anormal (como puede ser olor a quemado)
desconecte de inmediato la unidad y entre en contacto con su distribuidor local.
• Si nadie se encuentra presente para supervisar la operación de la unidad, por fa-
vor apáguela y desconéctela.
• No salpique o vierta agua en la unidad de aire acondicionado para evitar daños a
la unidad o un corto circuito.
• No coloque o cuelgue objetos que puedan gotear encima de la unidad.
• Asegúrese que la temperatura ambiente permanezca por encima del punto de
congelación (32°F o 0°C) para evitar que la unidad se agriete o se dañe.
• Mantenga las fuentes de calor lejos de la unidad de aire acondicionado.
• Asegúrese que la unidad se encuentra lejos del fuego y objetos inflamables o ex-
plosivos.

ENGLISHESPAÑOL
–15–
• No permita que niños o personas con capacidades físicas, sensoriales o mentales
disminuidas operen o estén cerca de la unidad sin la supervisión directa de un
adulto.
• No permita que los niños realicen la limpieza u otras operaciones de manteni-
miento sin la supervisión directa de un adulto.
• No intente reparar o desarmar usted mismo la unidad de aire acondicionado.
• Nunca inserte objetos en la unidad de aire acondicionado.
CONDICIONES DE OPERACIÓN
• La unidad de aire acondicionado debe ser operada dentro de un rango de tempe-
ratura de 62°F a 95°F (16°C a 35°C).
• Se debe dejar un perímetro de 12′′ (30 cm) libre de objetos alrededor del aire
acondicionado.
• No opere el aire acondicionado en climas húmedos.
• Mantenga la entrada y salida de aire limpias y libres de obstáculos.
• Durante la operación, cierre las puertas y ventanas para mejorar el efecto de en-
friamiento.
• Coloque el aire acondicionado sobre una superficie plana y suave para evitar el
ruido y la vibración al estar operando.
• No incline o ponga de cabeza la unidad de aire acondicionado. Si hay algún pro-
blema desconecte de inmediato y entre en contacto con su distribuidor local o
soporte técnico.

ENGLISH ESPAÑOL
–16–
FAMILIARIZÁNDOSE CON SU UNIDAD
DE AIRE ACONDICIONADO
1
2
3
4
5
1. Salida de aire frío
2. Cuchillas direccionales de aire frío
3. Entrada de aire caliente
4. Cable de suministro de energía
5. Panel de control

ENGLISHESPAÑOL
–17–
USANDO SU UNIDAD DE AIRE ACONDICIONADO
DESCRIPCIÓN GENERAL DEL PANEL DE CONTROL
h
g
f
e
i
a
b
c
d
NCIONES PRINCIPALES
1. Botón POWER: use este botón para encender y apagar su unidad de aire acondicionado
2. Botón MODE: Con este botón puede recorrer los diferentes modos de funciona-
miento: modo de enfriamiento (cooling), modo de deshumidificador (dehumidi-
fier), y ventilador (fan)
3. Botón FAN
4. Botón RESET FILTER
5. Botón DELAY/TIMER
6. Botón TEMPERATURE +/-: permite ajustar la temperatura deseada en la habita-
ción al presionar el botón adecuado (▲/ ▼). Los cambios de temperatura se reali-
zan en pasos de 1° en el rango de 61°F (16°C) a 86°F (30°C). NOTA: no es posible fijar
la temperatura en los modos de deshumidificador o ventilador.
7. Pantalla LED de Temperatura: En el modo de enfriamiento muestra la temperatura
deseada en la habitación. En los otros modos la pantalla estará en blanco.
INDICATORS (WHEN ILLUMINATED)
a. Velocidad automática del ventilador
b. High: velocidad alta del ventilador
c. Med: velocidad media del ventilador
d. Low: velocidad baja del ventilador
e. Cool: modo de enfriamiento
f. Energy saver: modo de ahorro de energía
g. Limpie y reemplace el filtro
h. Temporizador activado

ENGLISH ESPAÑOL
–18–
CONTROL REMOTO
1. Botón ON/OFF
2. Botones Fan +/-
3. Botones de temperatura ▲/▼
4. Botón Mode
5. Botón Auto
6. Botones del Temporizador +/-
7. Botón Timer (DELAY)
USANDO EL CONTROL REMOTO
BOTÓN ON/OFF
Presione el botón ON/OFF para encender o apagar la unidad.
BOTONES FAN +/-
Presione el botón correspondiente para aumentar (+) o disminuir (-) la velocidad del ven-
tilador. Presione el botón AUTO para una selección automática apropiada de la velocidad
del ventilador de acuerdo a la temperatura ambiente de la habitación y una operación
más eficiente de la unidad.
BOTONES DE TEMPERATURA ▲/ ▼
Ajuste la temperatura deseada en la habitación al presionar el botón adecuado. Los cam-
bios de temperatura se realizan en pasos de 1° en el rango de 61°F (16°C) a 86°F (30°C). No
es posible fijar la temperatura en los modos de deshumidificador ventilador.
BOTÓN MODO
Con este botón puede recorrer los diferentes modos de funcionamiento: modo de enfria-
miento (cooling), modo de deshumidificador (dehumidifier), y ventilador (fan).
BOTÓN AUTO
Presione este botón para tener una selección automática apropiada de la velocidad del
ventilador de acuerdo a la temperatura ambiente de la habitación y una operación más
eficiente de la unidad.