Indesit WD 10 User manual

M
Washer-dryer
Instructions for installation and use
WD 10

Herearethe13topicsexplainedinthismanual.Read,learnand
have fun: you will discover many secret ways to get a better
wash,moreeasilyandmakingyourwasher-dryerlastlonger.
Quick guide
1. Installation and removal (p. 11)
Installation,afterdeliveryortransport,isthemostimportantoperation
for the correct functioning of your washer-dryer.Always check:
1. Thatthe electric systemconforms toregulations;
2. Thatthe inletand drainingpipes areconnected correctly.
Never use pipes that have already been used.
3. Thatthe washer-dryeris levelledproperly; something
worth checking to aid the performance of your
washer-dryer;
4. That the drum's fixing screws have been removed from
the back of the washer-dryer;
2. What goes in your washer-dryer and how
to start it (p. 2)
A correct distribution of your laundry is vital to the successful
outcomeofthe washand thelife ofthe washer-dryer.Learnall the
tips and secrets to dividing your linen: colour, type of fabric.
3. Guide to understanding labels (p. 6)
Thesymbolsonthelabels ofyourgarments areeasyto understand
and equally important for the success of your wash. The guide
includessimple instructions tohelp you choosethe right tempera-
ture, wash cycles and ironing methods.
4. Useful tips to avoid mistakes (p. 7)
Years back, our grandmothers were the ones who gave us good
advice - and in those days synthetic fibres did not exist: washing
was easy. Today, your washer-dryer offers you helpful advice
allowing you to wash wool even better than an expert laundress
would by hand.
5. The detergent dispenser (p. 8)
How to use the detergent dispenser.
6. Understanding the control panel (p. 3)
Washer-dryer’s control panel is very simple. It has only a few
essential buttons to help you choose any type of wash cycle,
rangingfrom themost energetic, capableofcleaning amechanic’s
overalls,to themost delicate for wool.Familiarisingyourself withit
will help you get the best out of your wash while helping your
washer-dryer last longer.It’s easy.
7. Guide to the wash programmes (p. 4)
Herein is an easy table to help you choose the right programme,
temperature,detergentsand possible additives.Choose the right
programme and you will get better results with your wash while
saving time, water and energy, day after day.
1 Instructions for installation and use
8. How to dry (p. 5)
A few handy tips to get the best drying cycle from your appliance.
9. Care and maintenance (p. 13)
With just a bit of care, it will repay you with loyalty and devotion.
With the necessary upkeep, it will wash for years and years to
come.
10. Problems and solutions (p. 9 and 10)
Beforecalling atechnician,read thesepages: immediatesolutions
may be found for a number of problems. If the problem persists,
call your local Indesit customer services who will be pleased to
help.Any failure will be repaired, as soon as possible.
11. Technical characteristics (p. 10)
Herein arethe technical featuresof your washer-dryer:model type
number, electric and water specifications, size, capacity, speed of
thespincycleandcompliance withItalianandEuropean regulations.
12. Safety for you and your family (p. 14)
Here you will find the necessary safety guidelines, and it is
important for you to read this section carefully.
13. Indesit stays with you after your purchase (p. 15)
Indesit supports its products after their purchase by offering you a
range of special services, professional assistance, spare parts
and quality accessories.

What goes in your washer-dryer?
Before washing,youcandoa great deal to ensurebetterresults.Divideyourgarments
according to fabric and colour. Read the labels, follow their guidelines.
Beforewashing.
Divide your washing according
to the type of fabric and colour
fastness.
Emptyall pockets (coins,paper,
moneyand small obejects)and
ensure all loose buttons are
repaired or removed prior to
loading.
How to eliminate the most common stains
Ink and biro Dab with a wad of cotton soaked in methyl alcohol or alcohol at 90°.
Tar Dab with fresh butter, rub in turpentine then wash immediately.
Wax Scrape away, then run a hot iron between two sheets of absorbent paper. Then rub in cotton with turpentine or
methyl alcohol.
Chewing gum Rub in nail polish remover and wipe with a clean rag.
Mold Cotton and white linen should be placed in a solution of 5 parts water, one bleach and a spoon of vinegar, then
washed immediately. For other white fabrics, use hydrogen peroxide at 10 volumes and wash immediately.
Lipstick Dab with ether on wool or cotton. Use tricloroetilene for silk.
Nail polish Place a sheet of absorbent paper on the side of the stain, wet it with nail polish remover, shifting the
garment as the sheet gradually changes colour.
Grass Dab with a wad of cotton soaked in methyl alcohol.
Startingthewasher-dryer
Starting your washer-dryer in
therightway isimportant forthe
quality of your wash, to help
prevent future problems and
enhancelife expectancyof your
appliance. Once you have
loaded your washer-dryer and
added the detergent together
with any fabric conditioner,
always check that:
1.The door is closed correctly.
2. The plug is secured in the
socket.
3. The water supply is turned
on.
4.Selector knob Aispositioned
on one of the symbols (Stop/
Reset).
Choosethedesiredprogramme
The programme is selected
accordingtothetypeofgarments
thatneedtobewashed.Tochoose
aprogramme,refertothetableon
page 4. Turn knob Auntil the
selected programme is aligned
withthemarkontheknob,check
that knob Bis in the desired
position,ifnecessaryusebuttons
D, E, F and lastly, press on/off
buttonG (Iposition).
Afterinstalling yournewwasher-dryer,startawash cycle
by setting programme "1" at 90 degrees.
For more delicate
garments:
protect underwear, tights
and stockings and delicate
items by placing them in a
canvaspouch
Dividing your garments
accordingtofabricand
colour, is very important
for good results
Atthe endof the wash cycle...
Lamp Hwill flash quickly for a
few seconds, then it will begin
flashing more slowly.
Then turn the washer-dryer off
by pressing on-off button G
(Oposition).You can now open
the washer-dryer door safely.
After having removed the
freshly cleaned washing, leave
the door open to allow air
circulationinside the drum.
Alwaysdisconnect electricity at
thesocket andturnoffthewater
supply.
Remember that, in the event
of a power failure, or should
the washer-dryer switch itself
off, the programme chosen
will remain in its memory.
The labels say it all.
Always look at the labels: they
tell you everything about your
garment and how to wash it in
the best possible way.
The table on page 6 shows all
meanings behind these
symbols. Their recom-
mendations are important to
achieve better wash results.
Instructions for installation and use 2
M
Bigand small happily
together.
Thiswasher-dryerhas aspecial
electroniccontroldeviceforeven
distribution:beforethespincycle
starts, this device allows the
garments to positions
themselves, to minimise noise
and vibrations during the spin
cycle.

H I
A
B
G
C
EFD
123
Anti-crease
This button allows you to
interrupt a programme (on
symbol )keepingthewashing
soakingin waterbeforethespin
cycle. It is a very useful button
in particular because it can be
used for delicates and
synthetics. It is only to be used
with wash programmes for
synthetic fabrics, silk and
curtains whenitisimpossiblefor
you to take the washing out
immediately.Beforeopening the
washingmachinedoor,finish the
wash cycle as follows:
Silk and curtains:
pressbuttonD
and the machine will drain the
water.
Synthetic fabrics:
pressbuttonD
if you want a spin cycle, or turn
knobAto symbol ifyouwant
thewater tobe drained.
N.B.:
With Daily wash, this function
is not performed.
Slow spin
Use this button to reduce the
spinning speed from 1000 to
500rpm forthe cotton andlinen
programmes and from 850 to
500 rpm for the synthetic
fabrics programmes.
ExtraEconomy
Reduces water consumption
during the rinse cycles. We
recommend that you use this
functiononly with smalllaundry
loads, dosing the detergent
proportionally.
Here I’m in command
Understandingthecontrolpanel
Making the right choice is important. And it’s easy.
Programme selector knob
Usethis knobtoselect thewash
programme.
Turn thisknobclockwiseonly.
To select a programme, you
should turn the knob so that the
symbol/number ofthedesired
programme is in line with the
pointerontheknob.
Now press on/off button G
(positionI),pilot lampHwillstart
flashing.
After 5", the setting will be
accepted, pilot lamp Hwill stop
flashing(stayinglit)andthewash
cyclewillbegin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols (Stop/Reset)andwait
5" : when the cancellation has
been accepted, pilot lamp H
flashes,andyoucanthenturnthe
applianceoff.
Afterthewashcyclehasbeenset
and accepted by the washing
machine, turning the knob will
have no effect (except for when
it is on position Stop/Reset).
Drying cycle knob
Use this knob to select the
desired drying cycle. Two
optionsare available:
A- Based on time:
From 40 minutes to150.
B- Based on the damp level of
thedry clothes:
Iron :use this slightly damp
setting for clothes that you
intend to iron to reduce effort
and save energy in the drying
cycle.
Wardrobe :use this setting
when you want dry clothes that
canbestored after hanging for
a short while.
Extra dry : use this setting
whenyou wantverydry clothes.
A cooling stage is foreseen at
the end of the drying cycle.
Detergent dispenser
It is divided into three
compartments:
1.Detergentfor pre-wash;
2.Detergent for the main cycle
wash;
3.Fabricconditioner.
The detergent dispenser is here.
3 Instructions for installation and use
On-off
When button G is pressed, the
washer-dryer is switched on,
when it is not the machine is
switched off.
Turning the appliance off
does not cancel the selected
programme.
On-off lamp / door locked
LampHflashes slowlywhenthe
appliance is switched on and
awaitinginstructionsand at the
endofa cycle,indicatingthatthe
door can be opened. It flashes
quickly when the door should
not be opened. A steady light
means the appliance has
accepted the selected
programme.
Drying cycle lamp
When this lamp is on, it means
that knob Bhas been set on a
dryingcycleandattheendofthe
washcycle,theappliancewillrun
theselectedtumbledryingcycle.

Type of fabric and degree of soil Programme
knob Detergent for prewash Detergent for wash Fabric softener Length of the cycle
(minutes)
Description of wash cycle
COTTON
Exceptionally soiled whites
(sheets, tablecloths, etc.) 1◆◆◆
165 Warm prewash, wash cycle at 90°C, rinse
cycles, intermediate and final spin cycles
Exceptionally soiled whites
(sheets, tablecloths, etc.) 2◆◆
145 Wash cycle at 90°C, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and fast colours 3◆◆
130 Wash cycle at 60°C, rinse cycles,
intermediate and final spin cycles
Slightly soiled whites and delicate colours
(shirts, jumpers, etc.) 4◆◆95 Wash cycle at 40°C, rinse cycles,
intermediate and final spin cycles
Rinse cycles ◆Rinse cycles, intermediate and final
spin cycles
Spin cycle Draining and final spin cycle
Drying cycle for cotton fabrics
Stop/Reset Interrupts/Cancels the selected programme
SYNTHETICS
Heavily soiled fast colour synthetics (baby
linen, etc.) 5◆◆
100 Wash cycle at 60°C, rinse cycles,
anti-crease or delicate spin cycle
Heavily soiled fast colour synthetics (baby
linen, etc.) 6◆◆95 Wash cycle at 50°C, rinse cycles,
anti-crease or delicate spin cycle
Delicate colour synthetics
(all types of slightly soiled garments) 7◆◆70 Wash cycle at 40°C, rinse cycles,
anti-crease or delicate spin cycle
Delicate colour synthetics
(all types of slightly soiled garments)8◆◆30 Wash cycle at 30°C, rinse cycles and
delicate spin cycle
Rinse cycles ◆Rinse cycles, anti-crease or delicate
spin cycel
Fabric softener ◆Rinse cycles with automatic introduction of
softener, anti-crease or delicate spin cycle
Spin cycle Draining and delicate spin cycle
Drying cycle for synthetic fabrics
Stop/Reset Interrupts/Cancels the selected programme
DELICATES
Wool 9◆◆60 Wash cycle at 40°C, rinse cycles and
delicate spin cycle
Particularly delicate garments and fabrics
(curtains, silk, viscose, etc.) 10 ◆◆50 Wash cycle at 30°C, rinse cycles,
anti-crease or draining
Rinse cycles ◆Rinse cyclesi, anti-crease or draining
Spin cycle Draining and delicate spin cycle
Draining Draining
Stop/Reset Interrupts/Cancels the selected programme
A programme for all seasons
What are you washing today?
Instructions for installation and use 4
Daily wash Your washer-dryer has a programme available for the washing of lightly soiled garments in a short amount of time.
By setting programme 8 at a temperature of 30°C, you can wash different types of fabrics together (except for wool and silk), with a
maximum load of 3kg. This programmes allows you to save on both time and energy as it only lasts around 30 minutes.
We recommend the use of liquid detergent.
Important: to cancel the wash programme you have just set, select one of the symbols (Stop/Reset) and wait for at least 5 seconds.
Special programme
The data found in the table is purely indicative, and can vary according to the quantity and type of washing, the water system temperature and
the room temperature.

Fabric
type Load type Max. load (kg) Extra
dry Wardrobe Iron
Cotton,
Linen Clothing of different
sizes 2,5 150 145 140
Cotton Terry
towels 2,5 150 145 140
Terital,
Cotton Sheets, Shirts 2,5 100 90 85
Acrylics Pyjamas,
socks, etc. 1656060
Nylon Slips, tights,
stockings,
etc. 1656060
5 Instructions for installation and use
How to dry
AcombinedWashingand
DryingProgramme
Look at table Ato the side and
follow the instructions provided
for MAX load to have an
automatic washing and drying
cycle.
Followthe instructionsfor wash
only(seepage2, theparagraph
entitled "Starting the Washer-
Dryer") and use knob Bto set
thetype ofdrying cycle desired,
thenpress button G(Iposition).
Ifthe laundryload tobe washed
and dried exceeds the
maximum load foreseen (see
table A), then follow the
instructions provided for wash
only(seepage2, theparagraph
entitled "Starting the Washer-
Dryer").
When the wash cycle has
finished,remove your washing,
divideit upand replace part ofit
insidethe drum.
Now follow the instructions
provided for a dry only cycle.
Repeat this procedure for the
remainderofthe load.
Dry only
Once you have loaded the
washing that needs drying (2,5
kg max. for cottons, see table
for other fabrics ), make sure
that:
- the door is shut correctly;
-theplugisinsertedinthesocket;
- thewater tapisturnedon;
-buttonGhasnotbeen pressed
(Oposition).
And now set the wash cycle
knob
Set knob Aon the appropriate
dryingsetting depending on
thetypeoffabric,select thetype
of drying cycle required using
knob Band then press on-off
buttonG(Iposition).
Attheendofthedryingcycle...
Wait for lamp Hto flash slowly,
thenturnthe washer-dryeroffby
pressing on-off button G
(Oposition).Now you canopen
the appliance door. Once you
haveremovedthe washingfrom
the appliance, leave the door
open or ajar to avoid the
formation of bad odours and
turn off the water tap.
A.
- During the drying phase, the door tends to get quite hot.
- Do not use the appliance to dry clothes that have been
washed with flammable solvents (e.g. trichlorethylene).
- Do not use the appliance to dry foam rubber or similar
elastomers.
- Make sure that the water tap is turned on during the drying
cycles.
- This washer-dryer can only be used to dry clothes which
have been pre-washed in water.
WARNING
A spin cycle is carried out during the drying if you have set a
cotton programme and a level of dryness (Extra dry ,
Wardrobe , Iron ).
IMPORTANT
Dryingtime(Min.)
The data contained in the table are purely indicative.
For cotton loads of less than 1 Kg, use the drying programme
designed for synthetic fabrics.

Wash Bleaching Ironing Dry cleaning Drying
Strong
action
Delicate
action
High
Temp.
Low
Temperat.
Wash at
95°C Bleaching only in cold water Hot iron at max 200°C Dry clean with any solvent Machine dryable
Wash at
60°C Do not bleach
Medium hot
ironing at
max 150°C
Dry clean only with
perchloride, benzine
av., pure alcohol,
R111 and R113 Do not machine dry
Wash at
40°C Iron at max 110°C
Dry clean with av.
benzine, pure alcohol
and R113 Spread to dry
Wash at
30°C Not ironable Do not dry clean
Hang to dry
without spin
drying
Hand wash Dry on clothes hanger
Not
washable in
water
Understanding labels
Learnthemeaning of these symbolsandyouwill get better
results, your garments will last longer resulting in an
improvedwash.
Allover Europe,garmentlabels
containmessages expressedin
small yet important symbols.
Understanding them is very
important if you want to get
better results and treat your
garmentsthe way theydeserve
tobe treated.
These symbols are divided in
five different categories and
shapes:washing , bleaching
, ironing ,dry cleaning
and drying .
Consult and learn the symbols in this table: they will help you
obtain a better wash, treat your clothes properly, and get a
better performance out of your washer-dryer.
Useful tips
Turn shirts inside out to get better results
and make them last longer.
Always empty pockets of their contents.
Look at the label: it will always give you useful
advice.
When loading your washing, try to have a mixture
of large to small items. Make sure you select the right
temperature!
Instructions for installation and use 6
l
c
A
P
F

Usefultips
Never use your washer-
dryer to wash... torn, fraying or
non-hemmed linen. If it is
absolutelyneccessary,placeitin
abagforprotection.Donotwash
colouredlinenwith whites.
Watchthe weight!
For best results, do not exceed
the weight limits stated below
(figures show weight of dry
garments):
- Resistant fabrics:
5 kg maximum
- Synthetic fabrics:
2.5 kg maximum
- Delicate fabrics:
2 kg maximum
- Pure new wool:
1 kg maximum
How to wash almost anything
Curtains.
Curtains tend to crease a great
deal. A useful tip to reduce
creasing: fold the curtains and
place them in a pillow case or
meshbag. Donot loadanything
else inside the appliance, this
will ensure that the overall
weightdoes notexceed the half
load. Remember to use the
specific programme 10 which
automaticallyexcludes the spin
cycle.
Trainers.
Once you have removed mud
and dirt from trainers, you can
even wash them with jeans or
any other tough garments. Do
not wash trainers with whites.
Quilted coats and anorak.
Youcan washquilted coatsand
wind-cheaters, too, if they are
padded with goose or duck
down. Do not load more than
2-3 kg and never load 5 kg.
Repeat rinse once or twice
usingthegentle spin.
How much does it weigh?
1sheet400-500 gr.
1pillowcase150-200 gr.
1tablecloth400-500gr.
1bathrobe900-1,200gr.
1towel150-250 gr.
Coloured T-shirts, printed
onesandshirtslastlongerif turned
insideoutbeforewashing.
Printed T-shirts and sweatshirts
shouldalwaysbeironedinsideout.
Dungaree alert.
Very popular “salopette” type
overalls have straps with hooks
thatcandamagethedrumofyour
washer-dryerorothergarments
duringthe wash.Tominimisethe
risk, place hooks in the pocket
andfasten withsafety pins.
Holidays: unplug the
appliance.
It is recommended that you
shouldunplugthe machinefrom
thesocket and turnoff the water
supply. Leave the door ajar to
allow air circulation to the draw
andthedoorgasketarea.Thiswill
preventunpleasantodours.
7 Instructions for installation and use
For best results, we
recommend you use a
specific detergent, taking
carenotto washmorethan
1kgof laundry.
WOOLCYCLE

You must follow the dosage
recommendations provided by
themanufacturers whenadding
detergent or fabric conditioner.
Doseswill varyaccording to the
wash load, the water hardness
andhow soiledthewashing is.
Experience will help you select
the right dosage almost
automatically:itwillbecomeyour
secret.
Ensure no overfilling when
adding fabric conditioner in
compartment3.
Thewasher-dryerautomatically
addsthe softenerto thewash in
eachprogramme.
Liquid detergent is poured into
compartment 2just a few
seconds before starting the
wash cycle.
Rememberthat liquiddetergent
is only designed for wash
cycles of up to 60 degrees on
non pre-wash items.
Incompartment1:
Detergentfor pre-washing(powder)
Incompartment2:
Detergentfor washing
(powder or liquid)
Incompartment3:
Additives(softeners,perfumes, etc.)
Usefultipsabout thedetergentdispenser
It’s important for a good wash
The first secret is the easiest: the detergent dispenser is
opened by pull it outwards.
Specialcontainers aresold with
liquid or powder detergents for
placinginside the washer-dryer
drum, these are positioned
according to the instructions
foundinthe detergent box
Never use hand wash
detergent,because it may form
too much foam, which could
damagethe washer-dryer.
Detergentsthatare specifically
formulated for both hand and
machine wash are an
exception.
One last secret: when washing
with cold water, always reduce
theamountofdetergentyouuse:
it dissolves less easily in cold
water than in hot water, so part
of it would be wasted.
Cuttingcostsefficiently A guide to environmentally
friendly and economic use
of your appliance.
MAXIMISETHE LOADSIZE
Achieve the best use of energy, water, detergent and time by using the recommended
maximum load size.
SAVE up to 50% energy by washing a full load instead of 2 half loads.
DO YOU NEED TO PRE-WASH?
For heavily soiled laundry only!
SAVE detergent, time, water and between 5 to 15% energy consumption by NOT
selecting Prewash for slight to normally soiled laundry.
ISA HOT WASH REQUIRED?
Pretreat stains with stain remover or soak dried in stains in water before washing to
reduce the necessity of a hot wash programme.
SAVE up to 50% energy by using a 60°C wash programme.
BEFORE USING A DRYING PROGRAMME ...
SAVE energy and time by selecting the highest suitable spin speed to reduce the water
content in laundry before using a drying programme.
The detergent dispenser can be
removed and cleaned: pull it outwards,
as indicated in the figure.Then leave it
under running water for a few minutes.
Instructions for installation and use 8
123

The washer-dryer fails to
fill with water.
Is the hose correctly
connected to the tap?
Is there a water shortage ?
There could be work in
progress in your building or
street.
Is there sufficient water
pressure? The autoclave
maybe malfunctioning.
Is the tap filter clean? If the
water is very calcareous, or
if work has recently been
carried out on the water
piping, the tap filter could be
clogged with particles and
debris.
Is the rubber hose kinked?
The tract of the rubber hose
bringing water to washer-
dryer must be as straight as
possible. Make sure it is not
squashed or kinked.
Theprogrammeselector
knobkeepsturning?
Wait a few minutes for the
drain pump to empty the
tub, switch the washer-dryer
off,select one of thesymbols
stop/reset , then switch it
backon. Iftheknob continues
to turn, call for assistance
because it is showing an
anomaly.
Thewasher-dryer
continuouslyfillsand
drains water.
Isthe drain hosepositioned
too low? It must be installed
ata height ranging from60 to
100cm.
Is the end of the hose
immersed in water?
Does the wall drainage
system have a breather
pipe? If the problem persists
even after these checks, turn
the water supply off the
machine and call for
assistance.
Ifyou live onan upperfloorof
your building, there may be a
problemwithyourdrain trap.
To solve this problem, a
special valve must be
installed.
Before calling,read the following
Troubleshooting
In most cases, when your washer-dryer fails to work, the problems arising can
be easily solved without having to call for a technician. Before calling for
assistance, always check these points.
Thewasher-dryerfails to
start.
Istheplugcorrectlyinserted
intothesocket? It couldhave
beenmovedwhilstcleaning.
Is there electricity in the
house?
A circuit breaker may have
switched off as a result of too
many electrical appliances
working at the same time. Or
maybeduetoa generalfailure
inyourentirearea.
Is the washer-dryer door
closedproperly?
For safety reasons, the
washer-dryer cannot work if
the door is open or not shut
properly.
Is the On/Off button
pressed?
Ifitis,thenaprogrammedstart
hasbeen set.
Is the programmed start
knob,inthe correct position
for those models
concerned?
Is the water supply turned
on? For safety reasons, if the
washer-dryer does not load
water, it cannot start a wash
cycle.
RIGHT WRONG
Turn off the water
supply after use.
This will eliminate
the possibility of
leakage.
Always leave the
appliance door ajar
to avoid bad odours.
Clean the
appliance’s
exteriors gently.
To clean the
exteriors and the
rubber parts of the
appliance, always
use a soft cloth
dipped in warm and
soapy water.
Leave the washer-dryer
plugged in while
cleaning.
Even during maintenance,
the appliance should
always be unplugged.
Use solvents and
aggressive abrasives.
Never use solvents or
abrasives to clean the
external and rubber parts
of the washer-dryer.
Neglect the detergent
dispenser.
It is removable and can
easily be cleaned by
leaving it under running
water.
Go on holiday without
thinking about her.
Before leaving, always
make sure that the
washer-dryer is
unplugged and that the
water supply is turned off.
9 Instructions for installation and use
Simple: with the new Indesit technology, you need less than
half of it, to get good results on twice as much!
This is why you cannot see the water through the door:
because there is little, very little of it, to respect the
environment yet without renouncing maximum cleanliness.
And, on top of that, you are also saving electricity.
But where did all the water go?

Model WD 10
Dimensions width 59,5 cm
height 85 cm
depth 53,5 cm
Capacity from 1 to 5 kg for the wash programme; from 1 to 2,5 kg for the drying programme
Electrical
connections voltage 230/240 Volt 50 Hz
maximum absorbed power 2050 W
Water connections maximum pressure 1 MPa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)
drum capacity 46 litre
Spinning speed up to 1000 rpm
Control programs
in compliance with
IEC regulation 456
wash: programme 3, temperature 60°C. Carried out with 5 kg load;
drying: run with a load of 2.5 kg and knob Bset to position .
This appliance conforms with the following E.E.C. directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent
modifications
Too much foam.
Isthe detergent appropriate
formachinewashing?Check
whether the definition on its
labelreads“formachinewash”
or “hand and machine wash”,
oranyother similarwording.
Is the correct amount being
used?Anexcessiveamountof
detergent, besides producing
too much foam, does not
guarantee a more effective
wash,andcausesscalinginthe
internalpartsoftheappliance.
The washer-dryer does
not dry.
Checkwhether:
the plug has been correctly
insertedintothe socket;there
iselectricity inyour home;the
appliancedoor hasbeen shut
properly; a delayed start (if
available) has not been
selected;programme knob A
has been set to position
(Stop/Reset);the dryingcycle
knob Bhas been set to
position0.
The washer-dryer doesn't
dry properly.
Check whether:
the end of the drain hose is
underwater;thedrainpumpis
obstructed; the advice given
on the maximum loads has
beentaken; thewater taphas
beenturned on.
If,despiteallchecks,thewasher-
dryer fails to function and the
problem persists, call your
nearest authorised Customer
Service Centre, providing the
followinginformation:
- thenatureofmalfunction
- themodeltype no.(Mod.....)
- theserialnumber (S/N ....)
Thisinformationcanbefound on
thedataplatesituatedattheback
ofthewasher-dryer.
Is there space between the
machine and adjacent
units? If it is not a built-in
model, the washer-dryer will
oscillate a bit during the spin
cycle. A few cm of space
should therefore be left
aroundit.
The washer-dryer leaks.
Is the metal ring of the inlet
hose properly attached?
Turn off the water supply,
unplug the appliance and try
tightening its attachment
withoutforcingit.
Is the detergent dispenser
obstructed? Remove and
wash it under tap water.
Is the drain hose well
attached?Turn off the water
supply, unplug the appliance
and try tightening its
attachment.
Is the drain hose kinked?
The tract of the drain hose
must be as straight as
possible.Make surethe drain
hose is not squashed or
kinked.
Is the washer-dryer’s drain
duct clogged? Is there an
extension of the drain hose?
If so, is it positioned
incorrectly, blocking the
water flow?
Excessive vibration
during the spin cycle.
Havealltransit screws been
removed durind instal-
lation? See the following
page on installation
procedures.
Has the washer-dryer been
levelled correctly? The
levelling of the appliance
should be checked
periodically. Adjust the feet
and check them with a level.
The washer-dryer does
not drain or spin.
Does the selected
programme incorporates
water draining? Some
programmes stop at the end
of the wash cycles and
draining will have to be
selected manually.
Is the “Anti-crease"
function -where provided -
enabled? This function
requiresmanual selection for
draining.
Is the drain pump clogged?
To check it, turn off the water
supply, unplug the washer-
dryer and follow the
instructions on page 13, or
call for technical assistance.
Technical characteristics
Alwaysget
assistancefrom
authorised
techniciansand
always insist on
original spare parts.
Instructions for installation and use 10

11 Instructions for installation and use
When the new
washer-dryerarrives
Installationand removal
Whether new or just transported to a new house,
installation is extremely important for the correct
functioning of your washer-dryer.
Connecting the drain hose
The drain hose (hooked pipe) is
securedtotherearofthemachine
by support clips and may be
routedtorightorleftasrequired.
The hook to be used in case the drain
hose ends at a height below 60 cm.
Thedrain hoseshould beplaced
in a stand pipe with a minimum
internal diameter of 38 mm (1½
inches)oritcanbepositionedover
a sink or it can be connected as
shown in Fig. A. The height of
stand pipe or sink should be
between 60 and 100 cm (24 and
40 inches). Care must be taken
that the hose is not obstructed,
twisted, submerged or kinked. If
the hose is connected with an
airtightjoining,provisionshouldbe
madetopreventsyphoning.
The guide for draining into tubs and
sinks.
Fig. A
Electric connection
Your appliance is now supplied
with a 13 amp fused plug it can
bepluggedinto a13ampsocket
for immediate use. Before using
the appliance please read the
instructionsbelow.
WARNING - THIS APPLIANCE
MUST BE EARTHED.
THE FOLLOWING OPERATIONS
SHOULD BE CARRIED OUT BY A
QUALIFIEDELECTRICIAN.
Replacingthefuse:
When replacing a faulty fuse, a
13 amp ASTA approved fuse to
BS1362shouldalwaysbeused,
andthefusecover re-fitted.Ifthe
fuse cover is lost, the plug must
not be used until a replacement
isobtained.
Afterremovingtheappliancefrom
its packaging, check that it is
intact. If in doubt, contact a
qualifiedtechnicianimmediately.
The inside of the machine is
supported,fortransportation,by
fourscrewsonthebackpanel.
Before using the washer-dryer,
remove the screws, remove the
spacers together with the rubber
tubesattachedtothem(keepingall
theparts)andusetheplasticplugs
providedtofillintheholes.
Important:Usethecap(provided)
toclosethe3holeswhichhoused
the stop pin, situated in the right-
hand part of the lower back of the
washer-dryer.
Levelling
The washer-dryer must be
levelled appropriatey in order to
guaranteeitscorrectfunctioning.To
level the appliance, the front feet
must be adjusted; the angle of
inclination,measuredaccordingto
the worktop, must not exceed 2°.
Whenplacedoncarpet,makesure
theventilationisnotreduced.
The front feet are adjustable.
Connection to the water
mains
Both hot and cold water supplies
arepreferableandtheyshouldbe
between 34.5kN/m²(5lb/in²) and
1034.2kN/m²(150lb/in²)pressure.
Thehosehavingtheredendfitting
should be encountered between
the hot supply and the threaded
connectionadjacenttotheletterH
on the rear of the machine. The
hosehavingthewhiteendfittings
shouldbeconnectedbetweenthe
cold supply and the threaded
connectionadjacenttotheletterC
on the rear of the machine.
Remember to insert a sealing
washer at each connection to
ensure watertight joints. Do not
overtighten the connections by
usingtools-handtightissufficient
topreventleaks.Itisgenerallymore
convenienttohavethesesupplies
away from the sink taps. Where
no suitable hot water supply is
availableoritdoesnotmeetthese
requirements,bothinlethosesmay
be connected to a cold supply by
using two taps etc., or a «T»
junctionontheplumbinghowever,
useofcoldwateronlywillincrease
programmetimes.
Note: the maximum temperature
shouldnotexceed70°C(158°F).
The rubber gasket.
Connect the inlet hose to the
threaded connector on the
machinerear.
Water pipe inlet at the top right.
Warning!
The company denies all
liability if and when these
norms are not respected.
Plastic bags, expanded
styrofoam, nails and other
packaging parts are not
children’s toys, and are
potentially dangerous.
Retain the transit screws,
spacers and washers.
Should you move house
then these should be
replaced to support the
inside of the machine to
prevent damage when
transporting the machine.

Instructions for installation and use 12
Replacementfuse covers:
If a replacement fuse cover is
fitted, it must be of the correct
colour as indicated by the
coloured marking or the colour
thatisembossedinwords onthe
baseof theplug. Replacements
can be obtained directly from
yournearest Service Depot.
Removing the plug:
If your appliance has a non-
rewireablemouldedplugandyou
shouldwishtore-routethemains
cable through partitions, units
etc.,please ensurethat either:
the plug is replaced by a fused
13 ampere re-wearable plug
bearingtheBSImarkofapproval.
or:
themains cableis wireddirectly
into a 13 amp cable outlet,
controlled by a switch, (in
compliancewithBS5733) which
isaccessiblewithout movingthe
appliance.
Disposing of the plug:
Ensure that before disposing of
theplugitself,youmakethepins
unusable so that it cannot be
accidentally inserted into a
socket.
Instructions for connecting
cable to an alternative plug:
Important: the wires in the
mains lead are coloured in
accordance with the following
code:
Green &Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the
leadmaynotcorrespondwiththe
colouredmarkings identifyngthe
terminalsinyourplug,proceedas
follows:
Connect Green & Yellow wire to
terminal marked Eor or
colouredGreenorGreen&Yellow.
Connect Brown wire to terminal
markedLor colouredRed.
Connect Blue wire to terminal
marked NorcolouredBlack.
Ifa13ampplug(BS1363)isused
itmustbefittedwitha
13amp fuse, eitherin the plugor
adaptororatthedistributionboard.
If you are in any doubt the
electricalsupplytoyourmachine,
consult a qualified electrician
beforeuse.
How to connect an alternati-
ve plug:
Thewires in thismains leadare
colouredin accordancewith the
followingcode:
BLUE NEUTRAL(N)
BROWN LIVE(L)
GREEN&YELLOW EARTH(E)
Disposing of the appliance:
Whendisposingoftheappliance
please remove the plug by
cuttingthe mainscable asclose
aspossibletotheplug bodyand
disposeofitasdescribedabove.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP

Treat your machine well and it will provide
many years of trouble free service
Easy Care and Maintenance
Your washer-dryer is a reliable companion in life and on the job. It is just as important for you to keep it in
shape.
Your washer-dryer is designed
to provide reliable service over
manyyears. Afew simplesteps
will help to prolong its life and
avoid problems. It is advisable,
to turn off water taps when the
machine is not to be used, this
protectsthe hoses, etc.
If the water in your area is too
hard, use a deliming product
(water is hard if it often leaves
whitish stains around taps or
drains,especially ofbath tubs.
Formoreaccurateinformationas
to the type of water in your
system, call the local water
worksor alocalplumber).
Pockets must always be
emptied removing even pins,
badges and any other hard
object.
The washer-dryer exterior
should be cleaned with a rag
dipped in lukewarm water and
soap.
Neverexaggerate withdoses.
Normal detergents already
containdeliming agents. Onlyif
the water is particularly hard,
that is, rich in lime content, do
we recommend the use of a
specific product at every wash.
A periodical wash cycle with a
dose of a deliming product,
without detergents or washing,
may prove useful.
Never use too much detergent
or additives because this could
cause an excess amount of
foam, scaling and possible
damageto thecomponentparts
of your washer-dryer.
When in need, check the pump and the rubber hose.
The washer-dryer comes equipped with a self-cleaning pump that does not require any cleaning or maintenance.
Small objects may accidentally fall into the pump: coins, hair clips, loose buttons and other small items. To avoid
possible damage, they are withheld in an accessible pre-chamber, situated at the lower end of the pump.
It is important to wash
the detergent dispenser
regularly.
To preventdried washing
powderfrom
accumulating,placethe
dispenserunderrunning
water for a few minutes.
Do not forget to empty all pockets: small objects can
cause damage to your washer-dryer.
Attention: Before attempting to examine this pre-chamber, first
ensure that the machine has finished its programme and is empty.
Unplug the machine, as with any maintenance.
To gain access gently ease down the top of the plinth panel situated at
the base of the machine, with a screwdriver etc, to release it. Then
ease the top edge forward to allow it to be lifted clear (Fig. 1). Place
a shallow dish or tray below the cover of the pre-chamber to catch
the small amount of water present. Release the cover by turning anti-
clockwise (Fig. 2). Ensure that the cover is securely replaced.
Re-fit the plinth cover by inserting the hooks on its lower edge into
the slots and ease the top edge back into position.
The water inlet hose
Check the rubber hose at least once a year. If you see any cracks, replace it immediately. When you use your washer-dryer,
water pressure is very strong and a cracked tube could easily split open.
Fig. 1 Fig. 2
13 Instructions for installation and use

Instructions for installation and use 14
Your safety and that of
your family
Importantforthesafeuseofyourwasher-dryer
Your washer-dryer has been built in compliance
with the strictest international safety regulations.
To protect you and all your family.
Read these instructions and all
the information in this manual
carefully:they are an important
source, not only of numerous
useful tips, but also of vital
information on safety, use and
maintenance.
1. themachineshouldnotbe
installed in an outdoor
environment, not even
when a roof shelters the
area,becauseitmay bevery
dangerous to leave it
exposed to rain and
thunderstorms.
2. It must only be used by
adults and exclusively for
washing clothes following
the instructions provided in
thismanual.
3. Shouldit have tobe moved,
proceedwith thehelpof two
or three people and handle
it with the utmost care.
Never try to do this alone,
because the appliance is
very heavy.
4. Before loading the washer-
dryer,make sure the drum
is empty.
5. Never touch the washer-
dryer when barefoot or
with wet or damp hands
or feet.
6. Never use extensions or
multiple plugs, which are
particularly dangerous in
humid environments. The
power supply cable must
never be bent or
dangerously compressed.
7. Never open the detergent
dispenser while the
appliance is functioning;
do not use hand wash
detergent because the
abundance of foam could
damageitsinternal parts.
8. Never pull on the supply
cableor thewasher-dryerto
disconnect it from the wall
socket: it is extremely
dangerous.
9. While the appliance is
functioning, do not touch
the drain water as it could
reach very high tempera-
tures. The appliance door,
duringwash cycles,tends
to become hot; ensure
that children do no touch
it.Never force the washer-
dryer door because this
could damage the safety
lock which prevents
accidentalopeningwhenthe
nachine is working. Allow a
fewminutesat theendof the
program for the lock to
release.
10.In case of malfunctioning,
first close the water tap
and unplug the appliance
from the wall socket; do
not under any circum-
stancestouch internalparts
inorderto attempt repairs.
11. If you interrupt a Wash
Programme before its
end, then the water and
clothes may be hot. The
water level may also be
above the door, see
instruction for draining
the machine before you
open the door and handle
with caution .
12.During theTumble Drying
programmeand atits end,
the clothes and drum of
the machine may be hot,
handle with caution and
do not touch the drum.
Ionlywant anauthorised
specialisedtechnician with
original Indesitspare parts!
How to change the power supply cable
The power supply cable must only be replaced by one of our authorised Service Engineers.

We're as close to you as your telephone
For direct access to Genuine Indesit Spare Parts and Accessories,
call08705585850andspeaktoourskilledstaffwhocanhelpyoutoidentify andpurchasetheitemyourequire.
For a Rapid Response to a problem with your appliance, call 0870 607 0805. We're open from Monday to
Saturday(8am-5.30pmweekdays,9am-5pmSaturday).WehaveourowndepartmentofhighlytrainedIndesit
service staff. For most calls, our Service Engineer can fix the problem on the first visit.
Please have the following details to hand when you ring us:
Thenatureoftheproblem,theModelNumberandtheSerialNumber.
Thesenumberscanbe found ontheapplianceand on theportionofthe Registration Cardwhichyouretain.
Stay in touch
THANKYOU for choosing an Indesit appliance. We are confident
you have made a good choice and that your new appliance will give
many years of excellent service.
And we're there when you need us.
Registeryourpurchase
now
This will confirm your entitlement to enter our quarterlyprize draw
where you have the possibility to recover the cost of your purchase.
Simply completeand returnthe RegistrationFormsupplied with the
appliance documents, using the FREEPOST envelope supplied. Or
call the Registration Hotline on 0870 010 4305.
15 Instructions for installation and use

Instructions for installation and use 16

17 Instructions for installation and use

Instructions for installation and use 18

10/2002- 195029441.05- XEROX BUSINESSSERVICES - DOCUTECH
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel [phone]
Fax [phone]
www.merloni.com
Leader for young Europe