Indesit IWDC 7125 User manual

GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washer-dryer and
starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles,
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the drying cycle
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
arments requiring special care
Load balancing system
Precautions and tips, 9
eneral safety
Disposal
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
IWDC 7125
Instructions for use
WASHER-DRYER
English,1
GB
Español,13
ES

2
GB
Installation
 This instruction manual should be kept in a safe
place for future reference. If the washer-dryer is sold,
transferred or moved, make sure that the instruction
manual remains with the machine so that the new
owner is able to familiarise himself/herself with its
operation and features.
 Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its packaging.
2. Make sure that the washer-dryer has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 4
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washer-dryer needs to be moved to
another location.
 Packaging materials should not be used as toys for
children.
Levelling
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washer-dryer.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a ¾
gas threaded connection
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washer-dryer by
screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
 The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
 If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
 Never use second-hand hoses.
 Use the ones supplied with the machine.

GB
3
Technical data
Model IWDC 7125
Dimensions
width 59.5 cm
height 85 cm
depth 53,5 cm
Capacity from 1 to 7 kg for the wash programme;
from 1 to 5 kg for the drying programme
Electrical
connections
please refer to the technical data plate fixed
to the machine
Wate r
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed up to 1200 rotations per minute
Energy
rated
programmes
according to
regulation
EN 50229
Wash: programme 2; temperature 60°C;
run with a load of 7 kg.
Drying: first drying cycle performed with a 2 kg
load and the DRYIN knob on the setting;
Second drying cycle performed with a 5 kg
load and the DRYIN knob on the setting.
This appliance conforms to the following
EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
- 2006/95/EC Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
 We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
 the socket is earthed and complies with all
applicable laws;
 the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
 the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
 the socket is compatible with the plug of the
washer-dryer. If this is not the case, replace the
socket or the plug.
 The washer-dryer must not be installed outdoors,
even in covered areas. It is extremely dangerous to
leave the appliance exposed to rain, storms and other
weather conditions.
 When the washer-dryer has been installed, the
electricity socket must be within easy reach.
 Do not use extension cords or multiple sockets.
 The cable should not be bent or compressed.
 The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 2.

4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents
and laundry).
ON/OFF button: switches the washer-dryer on and
off.
WASH CYCLE knob: programmes the wash cycles.
During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to
select the available functions. The indicator light
corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the
cold wash cycle (see Personalisation).
DRYING knob: used to set the desired drying
programme (see Personalisation).
WASH CYCLE PROGRESS/DELAY TIMER
indicator light s: used to monitor the progress of the
wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time
remaining until the wash cycle starts will be indicated
(see next page).
DOOR LOCKED indicator light: indicates whether
the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or
temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash
orange, while the indicator light for the current wash
cycle phase will remain lit in a fixed manner. If the
DOOR LOCKED indicator light is switched off, the
door may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.
Standby mode
This washing machine, in compliance with new
energy saving regulations, is fitted with an automatic
standby system which is enabled after a few minutes
if no activity is detected. Press the ON-OFF button
briefly and wait for the machine to start up again.
Description of the washer-dryer and
starting a wash cycle
WASH CYCLE PROGRESS/
DELAY TIMER
indicator lights
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
DRYING
knob

GB
5
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see
Personalisation), after the wash cycle has been
started the indicator light corresponding to the
selected delay period will begin to flash:
As time passes, the remaining delay will be displayed
and the corresponding indicator light will flash:
The set programme will start once the selected time
delay has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to
indicate which phase of the cycle is currently in progress.
Note: when the drying cycle has finished, the
DRYIN knob should be returned to the 0 position.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding
indicator light will illuminate.
If the selected function is not compatible with the
programmed wash cycle, the corresponding indicator
light will flash and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the
indicator light corresponding to the first function
selected will flash and only the second function will be
activated; the indicator light corresponding to the
enabled option will remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is
locked to prevent it from being opened; make sure
the indicator light is off before opening the door (wait
approximately 3 minutes). To open the door during a
running wash cycle, press the START/PAUSE button;
the door may be opened once the DOOR LOCKED
indicator light turns off.
Starting a wash cycle
1. Switch the washer-dryer on by pressing the ON/OFF button. All indicator lights will switch on for a few
seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see Personalisation).
5. Set the drying cycle if necessary (see Personalisation).
6. Measure out the detergent and washing additives (see Detergents and laundry).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit
in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR
LOCKED indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the
drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.
Wash
Rinse
Spin/Drain
Drying
End of wash cycle

GB
Specials wash cycles
Sport Light ( wash cycle 9) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles". We recommend
using a liquid detergent and dosage suitable for a half-load.
Sport Shoes (
wash cycle 10) is for washing sports shoes; for best results, do not wash more than 2 pairs
simultaneously.
Express Wash & Dry (
wash cycle 13) was designed to wash and dry lightly soiled garments quickly. This cycle may
be used to wash and dry a laundry load of up to 0.5 kg in just 35 minutes.
To achieve optimum results, use liquid detergent and pre-treat cuffs, collars and stains.
Wash cycles
The infor ation contained in the table is intended as a guide only.
For all Test Institutes:
1) Test wash y le in omplian e with regulation EN 50229: set wash y le 2 with a temperature of 60°C.
2) Long wash y le for ottons: set wash y le 2 with a temperature of 40°C.
3) Short wash y le for ottons: set wash y le 4 with a temperature of 40°C.
Wash y les
Table of wash cycles
Des ription of the wash y le
Max.
temp.
(°C)
Max.
speed
(rpm)
Drying
Detergents Max. load
(kg)
Cy le
duration
Pre-
wash Wash Fabri softener Normal E o
Time Normal E o Time
Daily
1Cotton with prewash: extremely soiled whites. 90° 1200 lll l 7-171 -
2Cotton: extremely soiled whites. 90° 1200 l-ll 7-155 -
2Cotton (1): heavily soiled whites and resistant colours. 60° 1200 l-ll 7-153 -
2Cotton (2): heavily soiled whites and delicate colours. 40° 1200 l-ll 7-147 -
3Cotton: heavily soiled whites and resistant colours. 60° 1200 l-ll 73,5130104
4Coloured Cottons (3): lightly soiled whites and delicate colours. 40° 1200 l-ll 7 3,5 92 71
5Syntheti s: heavily soiled resistant colours. 60° 800 l-ll 3 2 85 72
Special
Wool: for wool, cashmere, etc. 40° 600 - - ll1,5 -55 -
7Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 - - ll 1-55 -
8Jeans 40° 800 l-ll 3-80 -
9Sport Light 30° 600 - - ll 3-68 -
10 Sport Shoes 30° 600 - - ll
Max. 2
pairs -50 -
Drying
11 Cotton dry - - l- - - 5- - -
12 Syntheti s dry - - l- - - 3- - -
13 Express Wash & Dry 30° 1200 l-ll0,5 -35 -
Partial wash cycles
Rinse -1200 l- - l7-36 -
Spin -1200 l- - - 7-16 -
Drain -0- - - - 7-2-

GB
7
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash . The washer-dryer will automatically prevent you
from selecting a temperature which is higher than the maximum value set for each wash cycle.
Setting the drying cycle
Turn the DRYIN knob to select the desired drying
option. There are two options:
A - Based on time: From 40 minutes to 180.
B - Based on the desired laundry dryness level:
Iron dry : suitable for clothes which will need ironing
afterwards. the remaining dampness softens creases,
making them easier to remove.
Hanger dry : ideal for clothes which do not need to
be dried fully.
Cupboard dry : suitable for laundry which can be put back in a cupboard without being ironed.
If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table),
perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back
in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this procedure for the
remainder of the load.
Drying only
Use the cycle selector knob to select a drying cycle (11-12) in accordance with the type of fabric. The desired drying
level or time may also be set using the DRYIN knob.
Functions
The various wash functions available with this washer-dryer will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in
conjunction with the selected wash cycle.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly
soiled cotton and synthetic fabrics (refer to the
"Table of wash cycles" ).   enables you to wash in less time
thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
 This function may not be used in conjunction with cycles 1, 2, 6, 7, 8, 9, 10, 11, 12, 13, , , .
1200- 00
Press this button to reduce the spin speed
 This function may not be used in conjunction with cycles 7, 11, 12, 13, .
Extra rinse
By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is
particularly useful for sensitive skin.
 This function may not be used in conjunction with wash cycles 11, 12, 13, , .
Delay timer
This timer delays the start time of the wash cycle by up to 9 hours. Press the button repeatedly until the indicator light
corresponding to the desired delay time switches on. The fifth time the button is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching
the set programme.
This option is enabled with all programmes.
Personalisation
Fabri
type
Load type Max.
load
(kg)
Cupboard
dry
Hanger
dry
Iron
dry
Cotton Clothing of different
sizes, Terry towels 5180170140
Synthetics Sheets, Shirts, Pyjamas,
socks, etc. 3140120100
Table of Drying times (guideline values)

8
GB
Detergents and laundry
Detergent dispenser drawer
ood washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance
and contribute to environmental pollution.
 Do not use hand washing detergents because these
create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
ompartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
 Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites.
 Empty all garment pockets and check the buttons.
 Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 7 kg
Synthetic fabrics: max. 3 kg
Delicate fabrics: max. 2 kg
Wool: max. 1,5 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Wool: all wool garments can be washed using
programme 6, even those carrying the "hand-wash
only" label. For best results, use special
detergents and do not exceed 1,5 kg of laundry.
12
3
Silk: use special wash cycle 7 to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle 7.
Jeans: Turn garments inside-out before washing and
use a liquid detergent. Use programme 8.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the
load is excessively unbalanced, the washer-dryer
performs the distribution process instead of spinning.
To encourage improved load distribution and balance,
we recommend small and large garments are mixed
in the load.

GB
9
Precautions and tips
 This Washer-dryer was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons
and must therefore be read carefully.
General safety
 This appliance was designed for domestic use only.
 The Washer-dryer must only be used by adults, in
accordance with the instructions provided in this manual.
 Do not touch the machine when barefoot or with
wet or damp hands or feet.
 Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
 Do not open the detergent dispenser drawer while
the machine is in operation.
 Do not touch the drained water as it may reach
extremely high temperatures.
 Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
 If the appliance breaks down, do not under any
circumstances access the internal mechanisms in
an attempt to repair it yourself.
 Always keep children well away from the appliance
while it is operating.
 The door can become quite hot during the wash cycle.
 If the appliance has to be moved, work in a group
of two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
 Before loading laundry into the Washer-dryer, make
sure the drum is empty.
 During the drying phase, the door tends to get
quite hot.
 Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
 Do not use the appliance to dry foam rubber or
similar elastomers.
 Make sure that the water tap is turned on during
the drying cycles.
Disposal
 Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
 The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.

10
GB
Care and maintenance
Cutting off the water and electricity
supplies
 Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washer-dryer and help to prevent leaks.
 Unplug the washer-dryer when cleaning it and
during all maintenance work.
Cleaning the washer-dryer
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of your
appliance
 Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washer-dryer is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
pre-chamber which protects the pump, situated in its
bottom part.
 Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washer-dryer (see
figure);
2. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
 Never use second-hand hoses.

GB
11
Troubleshooting
Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make
sure that the problem cannot be not solved easily using the following list.
Problem:
The Washer-dryer does not
switch on.
The wash cycle does not start.
The Washer-dryer does not take
in water (the indicator light for
the first wash cycle stage
flashes rapidly).
The Washer-dryer continuously
takes in and
drains water.
The Washer-dryer does not drain
or spin.
The Washer-dryer vibrates a lot
during the spin cycle.
The Washer-dryer leaks.
The "Functions" indicator lights
and the "start/pause" indicator
light flash, while one of the "phase
in progress" indicator lights and
the "door locked" indicator light
will remain lit in a fixed manner.
There is too much foam.
The washer-dryer does not dry.
Possible causes / Solutions:
 The appliance is not plugged into the socket fully, or is not making contact.
 There is no power in the house.
 The Washer-dryer door is not closed properly.
 The ON/OFF button has not been pressed.
 The START/PAUSE button has not been pressed.
 The water tap has not been opened.
 A delayed start has been set.
 The water inlet hose is not connected to the tap.
 The hose is bent.
 The water tap has not been opened.
 There is no water supply in the house.
 The pressure is too low.
 The START/PAUSE button has not been pressed.
 The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see Installation).
 The free end of the hose is under water (see Installation).
 The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the Washer-dryer to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to avoid this inconvenience.
 The wash cycle does not include draining: some wash cycles require the
drain phase to be started manually.
 The drain hose is bent (see Installation).
 The drainage duct is clogged.
 The drum was not unlocked correctly during installation (see Installation).
 The Washer-dryer is not level (see Installation).
 The Washer-dryer is trapped between cabinets and walls (see Installation).
 The water inlet hose is not screwed on properly (see Installation).
 The detergent dispenser drawer is blocked (for cleaning instructions, see Care
and aintenance).
 The drain hose is not fixed properly (see Installation).
 Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
 The detergent is not suitable for machine washing (it should display the
text for Washer-dryers or hand and machine wash, or the like).
 Too much detergent was used.
 The appliance is not plugged into the socket, or not enough to make contact.
 There has been a power failure.
 The appliance door is not shut properly.
 A delayed start has been set.
 DRYIN knob is in the 0 position.

12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
 Restart the programme to check whether the problem has been solved;
 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
 the type of problem;
 the appliance model (Mod.);
 the serial number (S/N).
This information can be found on the data plate applied to the rear of the washer-dryer, and can also be
found on the front of the appliance by opening the door.

ES
13
Español
Sumario
Instalación, 14-15
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Descripción de la lavasecadora y
comienzo de un programa, 1 -17
Panel de control
Pilotos
Poner en marcha un programa
Programas, 18
Tabla de programas
Personalizaciones, 19
Seleccionar la temperatura
Seleccione el secado
Funciones
Detergentes y ropa, 20
Contenedor de detergentes
Preparar la ropa
Prendas especiales
Sistema de e uilibrado de la carga
Precauciones y consejos, 21
Seguridad general
Eliminaciones
Mantenimiento y cuidados, 22
Interrumpir el agua y la corriente eléctrica
Limpiar la lavasecadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Limpiar la bomba
Controlar el tubo de alimentación de agua
Anomalías y soluciones, 23
Asistencia, 24
ES
IWDC 7125
Manual de instrucciones
LAVASECADORA

14
ES
Instalación
 Es importante conservar este manual para poder
consultarlo en cual uier momento. En caso de venta,
de cesión o de traslado, verifi ue ue permanezca
junto con la lavasecadora para informar al nuevo
propietario sobre el funcionamiento y brindar las
correspondientes advertencias.
 Lea atentamente las instrucciones: ellas contienen
importante información sobre la instalación, el uso y la
seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavasecadora.
2. Controle ue la lavasecadora no haya sufrido
daños durante el transporte. Si estuviera dañada no
la conecte y llame al revendedor.
3. Quite los 4 tornillos de
protección para el
transporte y la arandela
de goma con el
correspondiente
distanciador ubicados en
la parte posterior (ver la
figura).
4. Cubra los orificios con los tapones de plástico
suministrados con el aparato.
5. Conserve todas las piezas: cuando la lavasecadora
deba ser transportada nuevamente, deberán volver a
colocarse.
 Los embalajes no son juguetes para los niños.
Nivelación
1. Instale la lavasecadora sobre un piso plano y rígido,
sin apoyarla en las paredes, muebles ni en ningún
otro aparato.
2. Si el piso no está
perfectamente horizontal,
compense las
irregularidades
desenroscando o
enroscando las patas
delanteras (ver la figura);
el ángulo de inclinación
medido sobre la superfi-
cie de trabajo, no debe
superar los 2º.
Una cuidadosa nivelación brinda estabilidad a la
má uina y evita vibraciones, ruidos y desplazamientos
durante el funcionamiento. Cuando se instala sobre
mo uetas o alfombras, regule los pies para conservar
debajo de la lavasecadora un espacio suficiente para
la ventilación.
Conexiones hidráulicas y eléctricas
Conexión del tubo de alimentación de agua
1. Conectar el tubo de
tubo enroscándolo a un
grifo de agua fría con la
boca roscada de 3/4 gas
(ver la figura).
Antes de conectarlo,
haga correr el agua hasta
ue esté límpida.
2. Conecte el tubo de
alimentación a la
lavasecadora
enroscándolo en la toma
de agua correspondiente
ubicada en la parte
posterior derecha (arriba)
(ver la figura).
3. Controle ue en el tubo no hayan pliegues ni
estrangulaciones.
 La presión de agua del grifo debe estar
comprendida dentro de los valores contenidos en la
tabla de Datos técnicos (ver la página
correspondiente).
 Si la longitud del tubo de alimentación no es la
suficiente, diríjase a un negocio especializado o a un
técnico autorizado.
 No utilice nunca tubos ya usados.
 Utilice los suministrados con la má uina.

ES
15
65 - 100 cm
Conexión del tubo de descarga
Conecte el tubo de
descarga, sin plegarlo, a
una tubería de descarga
o a una descarga de
pared colocadas a una
altura del piso entre 65 y
100 cm;
o apóyelo en el borde de
un lavamanos o de una
bañera, uniendo la guía
suministrada con el
aparato, al grifo (ver la
figura). El extremo libre
del tubo de descarga no
debe permanecer
sumergido en el agua.
 No se aconseja utilizar tubos de prolongación, si
fuera indispensable hacerlo, la prolongación debe
tener el mismo diámetro del tubo original y no superar
los 150 cm.
Conexión eléctrica
Antes de enchufar el aparato, verifi ue ue:
 la toma tenga la conexión a tierra y haya sido
hecha según las normas legales;
 la toma sea capaz de soportar la carga máxima de
potencia de la má uina indicada en la tabla de
Datos técnicos (ver al costado);
 la tensión de alimentación esté comprendida dentro
de los valores indicados en la tabla de Datos
técnicos (ver al costado);
 la toma sea compatible con el enchufe de la
lavasecadora. Si no es así, sustituya la toma o el
enchufe.
 La lavasecadora no debe ser instalada al aire libre,
ni si uiera si el lugar está reparado, ya ue es muy
peligroso dejarla expuesta a la lluvia o a las
tormentas.
 Una vez instalada la lavasecadora, la toma de
corriente debe ser fácilmente accesible.
 No utilice prolongaciones ni conexiones múltiples.
 El cable no debe estar plegado ni sufrir
compresiones.
 El cable de alimentación debe ser sustituido sólo
por técnicos autorizados.
¡Atención! La empresa fabricante declina toda
responsabilidad en caso de ue estas normas no
sean respetadas.
Primer ciclo de lavado
Después de la instalación y antes del uso, realice un
ciclo de lavado con detergente y sin ropa,
seleccionando el programa 2.
Datos técnicos
Modelo IWDC 7125
Dimensiones
ancho 59,5 cm.
altura 85 cm.
profundidad 53,5 cm.
Capacidad de 1 a 7 kg para el lavado
de 1 a 5 kg para el secado.
Conexiones
eléctricas
ver la placa de características
técnicas aplicada en la má uina
Conexiones
hídricas
presión máxima 1 MPa (10 bar)
presión mínima 0,05 MPa (0,5 bar)
capacidad del cesto 52 litros
Velocidad de
centrifugado máxima 1200 r.p.m.
Programas de
control según la
norma EN 50229
lavado: programa 2; temperatura
60ºC; efectuado con 7 kg. de carga.
secado: primer secado realizado
con 2 kg de carga seleccionando el
nivel de secado .
Segundo secado realizado con 5 kg
de carga seleccionando el nivel de
secado .
Esta má uina cumple con lo
establecido por las siguientes
Directivas de la Comunidad:
- 89/336/CEE del 03/05/89
(Compatibilidad Electromagnética) y
sucesivas modificaciones
- 2002/96/CE
- 2006/95/CE (Baja Tensión)

1
ES
Contenedor de detergentes: para cargar
detergentes y aditivos (ver Detergentes y ropa).
Botón de ON/OFF: para encender y apagar la
lavasecadora.
Mando de PROGRAMAS: para elegir los programas.
Durante el funcionamiento del programa el mando no
se mueve.
Botones con pilotos de FUNCIÓN: para seleccionar
las funciones disponibles. El piloto correspondiente a
la función seleccionada permanecerá encendido.
Mando de SECADO: para seleccionar el secado
deseado (ver Personalizaciones).
Mando de TEMPERATURA: para seleccionar la
temperatura o el lavado en frío (ver
Personalizaciones).
Pilotos DE AVANCE DEL CICLO/COMIENZO
RETRASADO: para seguir el estado de avance del
programa de lavado.
El piloto encendido indica la fase en curso.
Si se seleccionó la función Comienzo retrasado,
indicarán el tiempo ue falta para la puesta en
marcha del programa (ver la página correspondiente).
Piloto PUERTA BLOQUEADA: para saber si la
puerta se puede abrir (ver la página correspondiente).
Botón con piloto START/PAUSA: se utiliza para
poner en marcha los programas o interrumpirlos
momentáneamente.
Nota: Presione este botón para poner en pausa el
lavado en curso, el piloto correspondiente centelleará
con color anaranjado mientras ue el de la fase en
curso permanecerá encendido en forma fija. Si el
piloto PUERTA BLOQUEADA está apagado, se
podrá abrir la puerta.
Para ue el lavado se reanude a partir del momento
en el cual fue interrumpido, presione nuevamente
este botón.
Modalidad de stand by
Esta lavasecadora está en conformidad con las
nuevas normativas vinculadas al ahorro energético.
Está dotada de un sistema de auto-apagado (stand
by) ue, en caso de no funcionamiento, se activa
pasados algunos minutos. Presionar brevemente el
botón ON/OFF y esperar ue la má uina se active.
Descripción de la lavasecadora y
comienzo de un programa
Piloto PUERTA
BLOQUEADA
Botón con piloto
START/
PAUSA
Panel de control
Contenedor de detergentes
Botón de ON/OFF
Mando de
PROGRAMAS
Botones con pilotos
FUNCIÓN
Mando de
TEMPERATURA
Mando de
SECADO
Pilotos DE AVANCE DEL
CICLO/COMIENZO
RETRASADO

ES
17
Pilotos
Los pilotos suministran información importante.
He a uí lo ue nos dicen:
Comienzo retrasado
Si se ha activado la función Comienzo retrasado (ver
Personalizaciones), después de haber puesto en
marcha el programa, comenzará a centellear el piloto
correspondiente al retraso seleccionado:
Con el transcurrir del tiempo se visualizará el retraso
residual con el centelleo de la luz testigo
correspondiente:
Una vez transcurrido el tiempo de retraso
seleccionado, comenzará el programa.
Pilotos fase en curso
Una vez seleccionado y puesto en marcha el ciclo de
lavado deseado, las luces testigo se encenderán
progresivamente para indicar su estado de avance:
Nota: al finalizar el ciclo de secado es necesario llevar
el mando SECADO hasta la posición "0".
Botones de función y pilotos correspondientes
Seleccionando una función, el piloto correspondiente
se iluminará. Si la función seleccionada no es
compatible con el programa elegido, el piloto
correspondiente centelleará y la función no se
activará. Si la función elegida no es compatible con
otra seleccionada precedentemente, el piloto
correspondiente a la primera función seleccionada
centelleará y se activará sólo la segunda, el piloto de
la función activada se iluminará.
Piloto puerta bloqueada
El piloto encendido indica ue la puerta está
blo ueada impidiendo su apertura; para poder abrir la
puerta es necesario ue dicho piloto esté apagado
(espere 3 minutos aproximadamente). Para abrir la
puerta mientras un ciclo está en curso, presione el
botón START/PAUSA; si el piloto PUERTA
BLOQUEADA está apagado, será posible abrir la
puerta.
Poner en marcha un programa
1. Encienda la lavasecadora presionando el botón ON/OFF. Todos los pilotos se encenderán durante algunos
segundos, luego se apagarán y se deberá pulsar el piloto START/PAUSA.
2. Cargue la ropa y cierre la puerta.
3. Seleccione el programa deseado con el mando de PROGRAMAS.
4. Fije la temperatura de lavado (ver Personalizaciones).
5. Seleccione el secado, si es necesario (ver Personalizaciones).
6. Vierta detergente y aditivos (ver Detergentes y ropa).
7. Seleccione las funciones deseadas.
8. Ponga en marcha el programa presionando el botón START/PAUSA y el piloto correspondiente permanecerá
encendido, fijo y de color verde. Para anular el ciclo seleccionado ponga en pausa la má uina presionando el
botón START/PAUSA y elija un nuevo ciclo.
9. Al final del programa se iluminará el piloto . Cuando el piloto PUERTA BLOQUEADA se apague, será
posible abrir la puerta. Extraiga la ropa y deje la puerta semicerrada para permitir ue el cesto se se ue.
Apague la lavasecadora presionando el botón ON/OFF.
Lavado
Aclarado
Centrifugado/Descarga
Secado
Fin del Lavado

18
ES
Programas particulares
Sport Light (programa 9) ha sido estudiado para lavar tejidos usados en prendas deportivas (chándales, pantalones
cortos, etc.) poco sucios; para obtener los mejores resultados es aconsejable no superar la carga máxima indicada
en la "Tabla de progra as". Se recomienda utilizar detergente lí uido y la dosis correspondiente a la media carga.
Sport Shoes (programa 10) ha sido estudiado para lavar calzado deportivo; para obtener los mejores resultados
no lave más de 2 pares a la vez.
Express Wash & Dry (programa 13) ha sido estudiado para lavar y secar prendas ligeramente sucias y en poco
tiempo: Seleccionando este ciclo se puede lavar y secar hasta 0,5 kg de ropa en sólo 35 minutos.
Para alcanzar los mejores resultados utilizar detergente lí uido; pre-tratar puños, cuellos y manchas.
Programas
Tabla de programas
Descripción del Progra a
Te p .
ax.
(°C)
Velocidad
áx.
(r.p. .)
Secado
Detergentes Carga áx.
(Kg.)
Duración del
ciclo
Prela-
vadoLavadoSuavi-
zante Nor al Eco
Ti e Nor al Eco
Ti e
Diario (programas para todos los días)
1Prelavado Algodón: blancos sumamente sucios. 90° 1200 llll
7-171 -
2Algodón: blancos sumamente sucios. 90° 1200 l-ll 7-155 -
2Algodón (1): blancos y colores resistentes muy sucios. 60° 1200 l-ll 7-153 -
2Algodón (2): blancos y colores delicados muy sucios. 40° 1200 l-ll 7-147 -
3Algodón: blancos sumamente sucios. 60° 1200 l-ll 73,5130104
4Algodón de color (3): blancos poco sucios y colores
delicados. 40° 1200 l-ll 7 3,5 92 71
5Sintético: colores resistentes muy sucios. 60° 800 l-ll 3 2 85 72
Programas Especiales
Lana: para lana, cachemira, etc. 40° 600 - - ll
1,5 -55 -
7Seda/Cortinas: para prendas de seda, viscosa, lencería. 30° 0 - - ll 1-55 -
8Jeans 40° 800 l-ll 3-80 -
9Sport Light 30° 600 - - ll 3-68 -
10 Sport Shoes 30° 600 - - ll
Max.2
pares -50 -
Programas de Secado
11 Algodón - - l- - - 5- - -
12 Sintético - - l- - - 3- - -
13 Express Wash & Dry 30° 1200 l-ll
0,5 -35 -
Programas Parciales
Aclarado -1200 l- - l7-36 -
Centrifugado -1200 l- - - 7-16 -
Descarga -0- - - - 7-2-
Progra as
Los datos contenidos en la tabla tienen un valor indicativo.
Para todos los Test Institutes:
1) Progra a de control según la nor a EN 50229: seleccione el progra a 2 con una te peratura de 60ºC.
2) Progra a algodón largo: seleccione el progra a 2 con una te peratura de 40ºC.
3) Progra a algodón corto: seleccione el progra a 4 con una te peratura de 40ºC.

ES
19
Seleccionar la temperatura
Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de progra as).
La temperatura se puede disminuir hasta el lavado en frío ( ).
La má uina impedirá automáticamente seleccionar una temperatura mayor ue la máxima prevista para cada
programa.
Seleccione el secado
Girando el mando de SECADO se selecciona el tipo de
secado deseado. Se han previsto dos posibilidades:
A - En base al tiempo: de 40 a 180 minutos.
B - En base al nivel de humedad de las prendas
secadas:
No Plancha : prendas ligeramente húmedas, fáciles
de planchar.
Para Colgar : prendas secas listas para guardar.
Para Doblar : prendas muy secas, aconsejado para toallas y batas.
Si excepcionalmente la carga de ropa para lavar y secar es superior al máximo previsto (ver la Tabla de tie pos
de Secado), realice el lavado, y una vez finalizado el programa, divida la carga y colo ue una parte en el cesto.
A partir de ese momento, siga las instrucciones para efectuar Sólo secado.
Repita las mismas operaciones para la carga restante.
Sólo secado
Gire el mando PROGRAMAS hasta una de las posiciones de secado (11-12) según el tipo de tejido, luego
seleccione la duración del ciclo de secado deseado con el mando SECADO.
Funciones
Las distintas funciones de lavado previstas por la lavasecadora permiten obtener la limpieza y el blanco deseados.
Para activar las funciones:
1. presione el botón correspondiente a la función deseada;
2. el encendido del piloto correspondiente indica ue la función está activa.
Nota: El centelleo rápido del piloto indica ue la función correspondiente no se puede seleccionar para el
programa elegido.
Seleccionando esta opción, se optimizan el movimiento mecánico, la temperatura y el agua para una carga
reducida de prendas de algodón y sintéticas poco sucias (ver la "Tabla de progra as").
Con   se puede lavar en un tiempo menor, ahorrando agua y energía. Se aconseja utilizar una dosis de
detergente lí uido adecuada a la cantidad de carga.
No se puede activar con los programas 1, 2, 6, 7, 8, 9, 10, 11, 12, 13, , , .
1200- 00
Presionando este botón se disminuye la velocidad de centrifugado.
No se puede activar con los programas 7, 11, 12, 13, .
Aclarado extra
Al elegir esta función aumentará la eficacia del aclarado y se asegurará la máxima eliminación del detergente. Es
útil para pieles particularmente sensibles.
No se puede activar con los programas 11, 12, 13, , .
Comienzo retrasado
Retrasa la puesta en marcha de la má uina hasta 9 horas.
Presione varias veces el botón hasta hacer encender la luz testigo correspondiente al retraso deseado. La uinta vez
ue se presione el botón, la función se desactivará.
Nota: Una vez presionado el botón START/PAUSA, se puede modificar el valor del retraso sólo disminuyéndolo hasta
ue se ponga en marcha el programa seleccionado.
Se puede utilizar en todos los programas.
Personalizaciones
Tipo de
tela
Tipo de carga Carga
áx.
(kg)
Para
Doblar
Para
Colgar
No
Plancha
Algodón Ropa de distintas
dimensiones, toallas 5180170140
Sintéticos Sábanas, Camisas,
Pijamas, calcetines, etc. 3 140 120 100
Tabla de tiempos de Secado (Valores indicativos)

20
ES
Detergentes y ropa
Contenedor de detergentes
El buen resultado del lavado depende también de la
correcta dosificación del detergente: si se excede la
cantidad, no se lava de manera más eficaz, sino ue
se contribuye a encostrar las partes internas de la
lavasecadora y a contaminar el medio ambiente.
 No use detergentes para el lavado a mano por ue
producen demasiada espuma.
Extraiga el contenedor de
detergentes e introduzca
el detergente o el aditivo
de la siguiente manera:
cubeta 1: Detergente para prelavado (en polvo)
cubeta 2: Detergente para lavado (en polvo o
líquido)
El detergente lí uido se debe verter sólo antes de la
puesta en marcha.
cubeta 3: Aditivos (suavizante, etc.)
El suavizante no se debe volcar fuera de la rejilla.
Preparar la ropa
 Subdivida la ropa según:
- el tipo de tejido / el símbolo en la eti ueta.
- los colores: separe las prendas de color y las
blancas.
 Vacíe los bolsillos y controle los botones.
 No supere los valores indicados, referidos al peso
de la ropa seca:
Tejidos resistentes: max 7 kg.
Tejidos sintéticos: max 3 kg.
Tejidos delicados: max 2 kg.
Lana: max 1,5 kg.
¿Cuánto pesa la ropa?
1 sábana 400/500 g
1 funda 150/200 g
1 mantel 400/500 g
1 albornoz 900/1200 g
1 toalla 150/250 g
Prendas especiales
Lana: con el programa 6 es posible lavar en la
lavasecadora todas las prendas de lana, aún las ue
contienen la eti ueta "sólo lavado a mano" Para
obtener los mejores resultados utilice un detergente
específico y no supere 1,5 Kg. de ropa.
12
3
Seda: utilice el programa correspondiente 7 para
lavar todas las prendas de seda. Se aconseja el uso
de un detergente específico para prendas delicadas.
Cortinas: pliéguelas y coló uelas dentro de una
funda o de una bolsa de red. Utilice el programa 7.
Jeans: vuelva del revés las prendas antes del lavado
y utilice un detergente lí uido. Utilice el programa 8.
Sistema de equilibrado de la carga
Antes de cada centrifugado, para evitar vibraciones
excesivas y para distribuir la carga de modo uniforme,
el cesto realiza rotaciones a una velocidad
ligeramente superior a la del lavado. Si después de
varios intentos, la carga todavía no está
correctamente e uilibrada, la má uina realiza el
centrifugado a una velocidad inferior a la prevista.
Cuando existe un excesivo dese uilibrio, la
lavasecadora realiza la distribución antes ue el
centrifugado. Para obtener una mejor distribución de
la carga y su correcto e uilibrado, se aconseja
mezclar prendas grandes y pe ueñas.