Indesit IND73W User manual

IND73W
English
GB
WASHING MACHINE
Instructions for use
Contents
General Safety Instructions, 2-5
Product Overview, 6
Getting Started: Installation, 7-10
Features, 11-12
Instructions, 13-19
FAQs and Troubleshooting, 20-21
Service, 22
Care and Maintenance, 23-25
Disposal, 26

2
General Safety Instructions
WARNING
CAUTION
ŸThis appliance has not been designed for commercial applications.
ŸThis appliance is intended to be used in household and similar applications such as:
– farm houses
– by clients in serviced apartments, holiday apartments and residential type
environments
ŸThis appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
ŸChildren should be supervised to ensure they do not play with the appliance.
ŸIf the supply cord is damaged, it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
ŸIf the machine must be placed on carpet, make sure the ventilation openings in the
base are not obstructed.
ŸConnect the washing machine to the water mains using new hose sets. Do not reuse
old hose sets.
ŸWater pressures between minimum 30kPa and maximum 800kPa are acceptable.
ŸMaximum capacity of this washing machine is 10kg.
ŸBefore connecting and turning on the washing machine, ensure the electrical voltage
and circuit frequency correspond to those indicated on the appliance.
ŸOnly connect the washing machine to a grounded (earthed) electrical outlet.

3
ŸDo not insert any objects into the appliance.
ŸDo not kink or damage the power cord, and position it out of the way so no one steps
on or places anything on the cord or against it.
ŸDo not overload the wall outlet. Overloading can result in fire or electric shock.
ŸNever use this washing machine with a power adaptor or an extension cord.
ŸUnplug the washing machine from the power supply before cleaning, servicing,
maintenance or moving the appliance. Pull by the plug, not by the cord.
ŸAfter use, always unplug the appliance and turn off the water.
ŸWARNING: All electrical work must be done in accordance with local and
national electrical codes as applicable and should be undertaken by licenced and
qualified persons only.
ŸInstall the washing machine on a flat surface to avoid overturning during use.
ŸInstall the washing machine so that there is a distance of at least 200mm between the
appliance enclosure and any external heat sources, such as appliances containing
heating elements.
ŸMake sure that all water and electrical connections are made by qualified personnel
only, observing local safety regulations and following the manufacturers instructions
(see Getting Started: Installation).
ŸImproper installation may result in the risk of fire, electric shock and/or injury.
ŸWe assume no liability for any eventual damages caused by improper installation.
ŸThe appliance is designed for private domestic use only.
ŸDo not operate the appliance outdoors.
ŸBefore loading the washing machine, always ensure no pet or young child has climbed
into it.
ŸMake sure all pockets of clothing to be washed are empty. Hard, sharp objects such as
coins, safety pins, bra wires, nails, screws or stones can cause extensive damage to the
appliance and block the pump.
ŸAny damage or malfunction resulting from foreign objects is not covered by your warranty
and may lead to expensive repairs.
ŸWe assume no liability for any eventual damages caused by improper or faulty use.
ŸBefore cleaning or carrying out maintenance, always unplug the appliance from the
power supply.
ŸExcept for the filters that require regular cleaning, the unit has no user-serviceable parts
contained within. Do not attempt to repair, disassemble or modify it. Repairs made by
inexperienced or unqualified persons may cause injury and/or make more serious
repairs to the appliance necessary.
ŸCAUTION: After each wash, check and clean the lint filter inside the drum. Also
check and clean the lint filter at the back of the machine next to the drain hose outlet on
a regular basis.
ŸThis appliance should only be serviced by an authorised service centre, and only
genuine spare parts should be used. Contact the after sales support line for advice.

4
WARNINGS

5
Do not wash water-proof clothing
CAUTIONS

6
Product Overview
Accessories included:
Hot inlet hose, cold inlet hose, drain hose with elbow, bottom cover and screws.
Specifications and technical parameters
Dimensions
601 (W) x 626 (D) x 985 (H) mm
Max. capacity
10 kg
Weight
47 kg
Rated voltage
230-240 V ~ 50 Hz
Rated power
450 W
Required water pressure
0.03 - 0.8 MPa
Waterproof grade
IPX4
Detergent box
Level indicator
Lid
Control panel
Adjustable leg (one on right side)
Wash/spin tub
Rollers (one on each back corner)
Handle (one on each side)
Housing
Softener dispenser
Cold and hot water connections (on back side)

7
Getting Started: Installation
CAUTION:
ŸInstall the washer on a stable and level
surface, in a dry location, out of sunlight.
ŸThe inbuilt levelling indicator (see page 6)
will help you determine whether levelling is
necessary. If so, adjust the adjustable leg
(at the front right side of the machine), as
illustrated, right. The maximum permissible
inclination of the supporting surface is 2°.
Unpacking
ŸThis product has been packaged to protect it against transportation damage. Keep
the original packaging carton in a safe place. It will help prevent any damage if the
product needs to be transported in the future. In the event that it is to be disposed
of, please recycle it and all other packaging materials where possible.
ŸPlastic wrapping can be a suffocation hazard for babies and young children, so
ensure all packaging materials are out of their reach and disposed of safely.
ŸUnwind the power cord to its full length and inspect it for damage. Do not use the
appliance if the appliance or its cord has been damaged or is not working properly.
In case of damage, contact our after sales support centre for advice on
examination, repair or return of the damaged product.
ŸRead this manual to familiarise yourself with all the parts and operating principles of
the washing machine. Pay particular attention to the safety instructions on the
previous pages.
Installing the bottom cover
ŸMake sure the power cord is unplugged from the
mains supply.
ŸPlace some padding (such as a soft mat, blanket or
thick towel) on the floor and gently lay the washing
machine on the padding, back side down. Take care
not to dent the housing.
ŸInsert the bottom cover into the hooks of the leg,
pushing it straight until it reaches into the front hooks.
ŸFasten the bottom cover with the supplied screw(s).
ŸCarefully set the washer upright.

8
Install the water inlet hoses to your hot and cold water taps, as described below.
ŸCheck and ensure that the sealing washers are firmly in place.
ŸAttach the straight end of the hose to your water taps. Make sure to attach the hot
water supply hose (with red markings) to the hot water tap and the cold water
supply hose (with blue markings) to the cold water tap.
ŸTighten the coupling nuts securely by hand, as illustrated below (the sealing
washer is part of and located inside the tap end).
ŸAttach the curved end of the hose to the corresponding inlet valve of the washer.
ŸTighten the coupling nuts securely by hand, as illustrated below.
ŸTighten the nut by turning it clockwise while holding the hose. (To detach the water
supply hose, turn the nut anticlockwise after turning the tap off.)
ŸTurn on the taps and check for leaks. Tighten the coupling nuts firmly if there is any
leakage. If your water pressure is strong, close the water tap completely, then open
it slightly.

9
CAUTION!
CAUTION!
CAUTION!
ŸThe drain hose and drain pump filter are located at the back of the machine, as
illustrated below, left.
ŸPinching the two bands of the clamp on the drain hose, connect it to the drain hose
connection at the back of the washer, as illustrated below.
ŸWhen the washer is in use, put the drain hose into a drain spout (or into a sink/tub),
as illustrated on page 10.

10
CAUTION!
Using the rollers
The washing machine is equipped with two rollers at the back that you can use to
move the machine more easily. Tilt the washing machine by about 30 degrees and
push forward, or pull backward, while holding the machine securely on both sides
with your hands, as illustrated below.
Do not move the machine on the rollers on uneven ground, which can damage the
rollers.
.
Take care of your
back! Do not tilt the washing
machine too much, which could
cause injury.
ŸWhile the washer is in use, make sure the height of the drain hose is at least 80cm,
otherwise the washer will not work well, or the water may flow out in the course of
washing. Also ensure the drain hose is not higher than 120cm above ground,
otherwise the washer will not drain water well.
ŸNever lay down the drain hose, as water will be discharged.
ŸBe sure the drain hose is properly routed so it will not kink or lift off the sink.
CAUTION:

11
Features
1. Detergent indication
These indicate how much powder detergent to use.
See Detergent and load recommendations, page 14, for details.
2. Time and preset indicators
This indicator shows the remaining time during washing, e.g.:
When setting soak and wash processes, this indicator shows the time you set, e.g.:
This indicator shows during presetting when the washing will be finished, e.g.:
When an abnormal condition occurs, it shows the warning code, e.g.:
3. Rinse indication
This indicator shows the number of rinses, e.g.:
4. Spin indication
This indicator shows the spin time in minutes (maximum 9 minutes), e.g.:
5. Start/Pause button
Press this button to start the washer operation.
During operation, press this button to stop the washer temporarily; press it again to restart
the washer operation.
NOTE: This is not a Cancel button.
1 2 3 4 5
6 7 8 9 10 11

12
6. Water Level button
You can choose the appropriate water level that matches the load size.
Different water levels for washing or rinsing are optional.
See 'Setting the water level ...', page 18, for details.
7. Preset/Ultrasonic button
Press this button to preset the finish time of the washing (not applicable for the Delicate
program).
To select or cancel the Ultra-sonic function, press and hold the button until the Ultrasonic
light is on or off. See page 19 for details.
8. Program/Child lock button
Press this button to choose the washing program: the relevant indicator light will start
flashing.
This button is also used to set the child lock function. See 'Child lock', page 19, for details.
The machine automatically sets certain washing processes for the Normal / Heavy Duty /
Custom and Wool wash programs. See page 19 for details.
9. Process button
Press these buttons to set various wash processes. See 'Setting the water level ...', page
18, for details.
Press the Soak / Variable Wash button before the start to set a soak time of up to 40
minutes (not applicable for the Delicate and Blanket programs).
10. Temperature button
Press this button if you want to choose the water temperature.
See 'Hot / cold / warm water wash', page 18 for details.
11. Power button
Press this button to switch the power on; press it again to switch the power off.
At the end of a washing program, the power will be switched off automatically after 5
seconds.
If you leave the washer switched on without starting the operation, the power will be
switched off automatically after 10 minutes of inactivity.

13
Instructions
80-120cm
1. Before washing, remove any coins, keys and other
hard items from pockets. Close any zippers to prevent
damaging your clothes and the wash tub. Brush dirt
and sand off clothes and turn pockets inside out.
2. Sort your washing into appropriate loads: whites,
coloureds, cottons, delicates, heavily soiled, etc.
Place delicate items into a wash bag for protection.
3. Load your washing items uniformly in the tub.
4. Add washing detergent (see page 14 for details).
5. Press the Power button.
6. Refer to the Program Selection Guide and select a suitable wash program. For the
Normal Heavy Duty and programs, the machine will automatically choose the correct
water power and level, wash and spin time and rinse type; for the and Custom Wool
programs, the machine will automatically select the correct water level. Other
parameters can be set individually (see page 15).
7. Close the lid and press the Start/Pause button. (If the washer lid is not closed properly,
the washer will sound an alarm and stop working before spinning.)
8. At the end of the wash, remove your washing, unplug the power plug from the wall
outlet and close the water taps. Leave the lid open until the interior has dried.
A Make sure the washer is stable and
level. The inbuilt levelling indicator (see
page 6) will help you determine whether
levelling is necessary. If so, adjust the
adjustable leg (front right) to stabilise
the washer (see page 7).
B Make sure the water inlet hoses are
properly installed (see page 8).
C Plug the machine into a nearby power
point.
D Open the water taps.
E Make sure the drain hose is properly
installed. Hang the upper end of the
hose over the laundry sink or into a
drain spout (see page 9).
F Before using the washing machine for
the first time, run a complete cycle
without laundry items.
Select the Normal program and run the
machine until the end of the program.

14
Program
Suitable items
Max.
Load
(kg)
Default settings
Wash time
(minutes)
Rinse
(times)
Spin time
(minutes)
Water
Level
Temp.
(Wash/Rinse)
Normal*
For normally soiled everyday
clothing and other items
10
Auto
(5~40)
6
Auto
(5~26)
Auto
(1~8)
Warm/Cold
Custom
Dependent on the custom
settings
10
10
2
5
Auto
(1~8)
Cold/Cold
Delicate
Delicate fabrics, lingerie
5
6
2
2
6
(3~8)
Cold/Cold
Heavy
Duty
Heavily soiled cottons,
workwear
10
Auto
(7~14)
2
Auto
(7~8)
Auto
(1~8)
Cold/Cold
Blanket
Blanket or bulky items
10
12
2
8
8
(5~8)
Cold/Cold
Wool
Delicates, knitwear
5
10
2
2
Auto
(1~8)
Cold/Cold
Test wash cycle in compliance with regulation AS/NZS 2040.1 and AS/NZS 2040.2: Normal, Max.
Water Level, Warm Temperature.
See page 17.
NOTE: it is recommended that powder detergent should be thoroughly dissolved in a
small amount of warm water before adding to the machine.
Dilute fabric softener with a little water and carefully add it to the softener dispenser on
the balance ring for dispersion through the final rinse.
CAUTION:
*
Water level indicator
Water level 1 2 3 4 5 6 7 8
Water volume (approx.) 28L 35L 44L 53L 65L 71L 81L 90L
Wash capacity (kg) Below 1 1–2.5 2.5–3.5 3.5–5 5–6 6–7.5 7.5–8.5 8.5-10
Detergent indicator
Amount of powder
detergent (g) 25–35 35–53 53–71 71–90
Liquid detergent Follow the recommendations on the detergent packaging.

15
Options
Program
Normal
Custom
Delicate
Heavy Duty
Blanket
Wool
Soak time (minutes)
-
-
Wash time (minutes)
Rinse time (times)
Spin time (minutes)
(Max. 3’)
PRESET time (hours)
-
4
This washing machine is equipped with a fuzzy logic function that automatically chooses
certain wash cycle processes for the Normal, Heavy Duty, Custom and Wool
programs. You do not have to adjust them yourself, however, if you want to adjust these
values yourself, proceed as follows:
1. Prepare your washing according to points 1 to 4 on page 13.
2. Press the Power button, then press the Program button to select the washing
program, e.g. Normal, Heavy Duty.
3. Press the appropriate process button to select the process and time you want to
adjust. The relevant indicator light will illuminate when the option is selected.
( selectable - non-selectable)
4. Press the Water Level button and choose an appropriate water level.
5. Close the lid and press the Start/Pause button for the washing program to start.
6. At the end of the washing program, a buzzer will sound to alert you that the program
has finished before the power is shut off automatically.
7. Close the water taps and unplug the power plug from the wall outlet.
8. If you want to use a particular customised program on a regular basis, you can
program it to the machine's memory for easy access the next time you want to use the
same program. See 'Memory function', page 19, for instructions.

16
on page 18.
on page 18.
On occasion you may want to select a single wash cycle process (or two processes)
instead of a complete program. For example, you may want to spin clothes that got
wet from rain while hanging on the line, or rinse and spin clothes washed by hand.
• To set a spin cycle only, set the WASH time and RINSE options to “0” and then
• To set a rinse and spin cycle, set the WASH time to “0”, then select a RINSE
option (from 1 to 4) and then the SPIN time (from 0-9 minutes). Then proceed as
Use this program for washing blankets or other bulky items. It will automatically select
the highest water level (90L), but you can adjust this manually down to 65L according
to the size of your bulky item(s).
1. Press the Power button and open the washer lid.
2. Press the Program button repeatedly until the indicator for the Blanket program
flashes.
3. Dissolve an appropriate amount of washing detergent with a little lukewarm water,
then pour the detergent solution directly into the tub of the washing machine.
4. Fold up the blanket and put it into the washing tub, as illustrated below.
5. Close the washer lid.
6. Press the Start / Pause button for the washing program to start.
7. At the end of the washing program, a buzzer will sound to alert you that the program
has finished before the power is shut off automatically.
8. Close the water taps and unplug the power plug from the wall outlet.
9. We recommend cleaning the lint filter after washing a blanket (see page 24 for
instructions).
NOTE: If you notice that the blanket floats up during the wash, press the Start/Pause
button, the washer will stop working temporarily. Push the blanket down and
press the Start/Pause button again to continue washing.

17
When using the delayed wash, we recommend
you use powder detergent. Do not add detergent
directly to the wash tub ahead of the wash time,
but follow the instructions below:
• Washing detergent: either put detergent into
the detergent box or, if you prefer to put it
directly into the wash tub, wrap the powder in a
small cloth.
• Fabric softener: dilute the softener with twice
the amount of water, then pour the solution into the softener dispenser.
This washing machine has a 0–24 hour preset function, which you can set to determine
the time when the washing program will finish. (It is, in effect, similar to a 'delayed start'
function, but you set the time period after which you want the wash to finish rather than
to start.)
NOTES: * The Preset function is not available for the Delicate program.
* To avoid water leakage when using this function, make sure the water taps
are open, the drain hose is properly installed and the washing load and
detergent are properly prepared.
1. Put your washing in the machine, loading items uniformly in the tub.
2. Press the Power button.
3. Select the required Program and process, and any other Water Level, Temperature
and Ultrasonic, if required.
4. Press the Preset button to select the desired time period (in hours) for the wash to
finish.
5. Select the water level, if necessary.
6. Add any detergents (see below and page 14 for details).
7. Close the washer lid and press the Start/Pause button.
8. After setting the Preset, the corresponding light will illuminate and all other lights will
be switched off about one minute later. (If you set the child lock, the Child Lock light
will be on.)
9. To check the preset program, press any button (except for the Power button); the
program will be indicated for 5 seconds. During these 5 seconds you can press the
Water Level button and set the water level.
10. To cancel the preset, shut off the power.
11. To change the preset time, first cancel the preset, then set it again.

18
Hot / cold / warm water wash
This top load washing machine must be connected to both a cold and a hot water tap.
You can then set it to use either just cold water for a cold water wash, or just hot water
for a hot water wash, or both hot and cold water for a warm water wash.
To select the wash temperature, press the Temperature button.
• Cold wash: the corresponding indicator light is on.
• Hot wash: the corresponding indicator light is on.
• Warm wash: both the Cold and Hot wash indicator lights are on.
Water power
The water power affects the pause time of the pulsator and hence the intensity of the
wash. It is automatically selected for the wash and rinse process, however, you can
also adjust it yourself (except for the Delicate and Blanket programs). To adjust the
water power level:
• Press the Start/Pause button, then press the Soak/Variable Wash button: the
display will show “H0”.
• Press the Soak/Variable Wash button again, repeatedly, to increase the water
power level from “H1”, “H2”, “H3” to the strongest, “H4”.
• Press the Soak/Variable Wash button again, repeatedly, to decrease the water
power level from “L1”, “L2”, “L3” to the weakest: “L4”.
Setting the water level and other processes
You can set the water level for wash and rinse processes. For example, if you are
sensitive to detergent residues in your washing, you may want to select a higher water
level for rinsing.
To set different water levels:
• Press the Wash button until the Wash light flashes; press the Water Level button
to choose the appropriate water level; press the Wash button to set the wash time.
• Then press the Rinse button until the Rinse light flashes; press the Water Level
button to choose the appropriate water level; press the Rinse button to set the
number of rinses.
To set other processes:
• Then press the Spin button until the Spin light flashes; press the Spin button to set
the Spin time.
• Finally press the Start/Pause button: the washer will start operating according to
the set values for wash and rinse water levels, number of rinses and spin time.
Other functions

19
Fuzzy control
For certain wash programs, the machine automatically detects the weight of your
wash load and selects the appropriate wash cycle processes.
• For the Normal and Heavy Duty programs, the machine will automatically select
the correct water power and level, wash and spin time, and rinse type.
• For the Custom and Wool programs, the machine will automatically select the
correct water level. Other wash cycle processes have to be manually set.
Ultrasonic function
Memory function
When you run the Normal, Custom or Heavy Duty program, the machine memorises
your settings (except for preset time and water level) for the next time you select it.
NOTE: This function is not available for the Wool, Blanket and Delicate programs.
Child lock
With the child lock activated, the machine will stop working automatically and sound
an alarm if the washer lid is opened for 4 seconds. To set the child lock:
• Press the Power button to switch on the power, then press and hold the Program
button for 4 seconds until a buzzer sounds. The child lock will be activated when
the Start/Pause button is pressed. Repeat the steps to cancel.
Start of washing
Washing will start when the water inside the tub has reached two levels below the set
level while the water will continue to flow in (see page 14 for the eight water levels).
This early start of washing will optimise the wash time and allow the detergent to
dissolve fully before the start of the set wash time. This function will be ineffective:
• When water level 1 (28L) or 2 (35L) is selected.
• When the Delicate or Blanket program is selected.
• When Soak is selected, after the soaking process.
This top load washing machine is equipped with an ultrasonic pump, which generates
vibrations into the wash tub. These vibrations help remove stains and dirt reducing the
required detergent amount and wash time.
To select this feature, press and hold the Preset/Ultrasonic button for four seconds
until the corresponding light comes on and a buzzer sounds. Repeat the steps to
cancel. When selecting the Ultrasonic wash, it is recommended to use less detergent
than usual.

20
FAQs and Troubleshooting
Not all unusual incidents you may encounter with your washing machine are faults, or
cause for concern. Check in the list below what issues may arise and why. Also check
in the table on the following page for solutions to other common problems.
• The drain hose is leaking water during the first use. Does this indicate there is
a problem?
No, this is normal; it is residual water from the performance test in the factory and
no cause for concern.
• Why is there still some water intake during the wash or rinse cycle?
When the water level is low, the washing machine will automatically refill during
the washing or rinsing process. This is no cause for concern.
• At the beginning of the spin cycle, why is the tub turning first and then
stopping?
This is intermittent spinning and it results in better spinning performance.
• During the spin cycle, why is the machine spinning and then stopping
suddenly and taking in water again?
If the washing is piled up at one side of the tub during the spin cycle, the washing
machine automatically takes in more water to redistribute the load. Once the load
is balanced again, the spin cycle will continue.
• Why is there a sound like water flowing after spinning?
This is the sound of the balancing liquid in the balance ring. This helps reduce
vibration during spinning.
• Why is the control panel still warm after the power is switched off?
This is caused by the memory circuitry still working.
• The washer does not work at all. What could I have done wrong?
• Check and ensure that the washer is connected properly to the power supply
and power is switched on at the outlet.
• If both are OK, first press the Power button, then press the Start/Pause button
and then press the Preset button.
• If the machine still does not start the set program, check elsewhere in your
home whether there has been a power failure, or whether the fuse or circuit
breaker has been activated.
If none of the solutions offered above and on the following page help you
solve the problem, contact our after sales support centre for advice.