Inel ORS-X1T Specification sheet

ORS-X1T
SINGLE CHANNEL RADIO RECEIVER WITH DECODER
for shutter, rolling door and grille drives.
Operation and installation manual
Safety notes
Basic notes
The ORS-X1T control unit is supplied in a condition allowing for safe operation and use, provided that all the guidelines
contained in this operation manual and applicable to the given use (e.g. gate or shutter), as well as current safety and accident
prevention regulations are observed.
The electrical components of the product may only be installed and repaired by qualified and licensed technicians.
Any modifications or changes to the product are not allowed. Warranty repairs may only be carried out by the manufacturer.
Only genuine spare parts and accessories may be used for post-warranty repairs.
The operating safety of ORS-X1T unit is guaranteed provided it is used according to the manufacturer's specification. The
limit values specified in the technical specification must be strictly observed.
Additional safety regulations
All important safety regulations and rules for preventing accidents applicable to the given application (e.g. gate or shutter)
must be adhered to when installing, starting up and maintaining the control unit. The following regulations are to be taken
into account in particular:
1. Fire safety regulations.
2. Accident prevention regulations.
GENERAL HAZARD AND SAFETY NOTES
The notes provided herein are general guidelines for using INEL control units in conjunction with other equipment. These
guidelines are to be strictly observed when installing and operating the equipment.
Warning - a warning note on potential damage to the control unit or other assets
in case of failure to adopt proper means of safety.
Danger - indicates an existing danger to life and health of the user in case of failure to apply appropriate means
of safety.
 Check that all screw connections are tight prior to installing the unit and setting the limit switches.
 Observe safety and accident prevention regulations applicable to the given use (e.g. shutter, gate).
 Before replacing fuses, unplug all power supply cables, then replace the fuse and reconnect the power cables.
 The ORS-X1T unit must be installed with adequate protections and protective devices required by applicable
regulations. The control units featuring crushing protection with a sensor installed on the gate, which the protection
acts upon contact of foreign body with the gate, must not cause any injuries caused from the movement of the gate.
 For INEL equipment with constant mains input to the unit, a switch ensuring safe voltage interruption (e.g. fuse-
switch), must be used apart from the safety fuse, installed in such way that all the connections can be easily
disconnected.
 Regularly inspect all cords and cables for damage to insulation and local breaks.
 In case of identifying cord damage, immediately disconnect the damaged cables from the mains and replace the
damaged cords.
 Before connecting the product to the mains it must be confirmed that its rated voltage conforms to the local mains
voltage.
CAUTION - IMPORTANT TO HUMAN SAFETY:
 do not allow children to play with the control unit;
 keep remote control devices out of children's reach;
 observe the moving system (e.g. gate, awning) and keep any bystanders away until full shutting or opening;
 all users of the gate must be trained or instructed on the principles of its operation and the related operating
hazards. Persons may be deemed as duly trained if the employer, administrator or owner has permitted them to
open the gate, and instructed them on how to use it.

ORS-X1T RECEIVER/DECODER SPECIFICATIONS
 Supply voltage 24 V DC/AC or 12 V DC
 Power input 10 mA (stand-by)
 Operating frequency 433.92 MHz
 Number of channels
1
 Range >>100 m
Fig. 1 Receiver/decoder Fig. 2 Wiring diagram
RECEIVER/DECODER OPERATION
An ORS-X1T remote control decoder with a built-in radio receiver can be used to control a single device. The decoder outputs
include two pairs of terminals connected to relay contacts. The decoder is compatible with
PIL-02XB, PIL-04XB, PIL-DL, PIL-PM, PIL-PT, PIL-NS and PIL-MMT remote controls. For DL, PM, PT, NS and MMT remote
controls, press UP or DOWN button to activate the decoder. The relay contacts will open approx. 1 second after the remote control
button is released. The decoder will not be activated by simultaneously pressing both remote control buttons.
RECEIVER/DECODER POWER SUPPLY
The decoder may be supplied with 12 V/24 V DC or 24 V AC. Fig. 2 shows the wiring diagram for all three cases.
REGISTERING REMOTE CONTROLS
Up to 15 different remote controls can be registered to a single decoder. Press SW1 to register a new remote control; green D1 LED
will turn on for 10 seconds; press the selected channel button on the remote control within 10 seconds. Red D1 LED will blink if the
registration is successful.
RESETTING REMOTE CONTROL CODES
All registered remote controls can be deleted from the memory. Press and hold SW1 for 10 seconds; D1 LED will change from green
to red. Release the button. All remote control codes will be deleted and the same or different remote controls can be registered.
NOTES ON RECEIVER/DECODER INSTALLATION
The decoder includes a high sensitivity built-in radio receiver. Each product is individually tested and has a range in the open area of
up to 200 m. After installing the decoder, check its range and correct operation before connecting other devices. Do not press any
remote control buttons more often than once every second. Pressing the buttons too often will not cause the control unit to switch to
the next stage, i.e. it will not execute the next command. In case of any issues with the range or correct operation, check the power
supply voltage. A minimum voltage to guarantee correct operation and range is 24 V AC/DC or 12 V DC. If the range is limited with
a correct supply voltage, change the location of the radio receiver.
Limited range may be due to:
1. Receiver positioned too low (the optimum height is 2-3 metres above the transmitter level).
2. Receiver too close to a large metal object.
3. Receiver enclosed by metal sheets, metal structures etc.
The range can be improved by changing the receiver location. Connect the controlled devices, if good range can be ensured. Please
allow for a delay of approx. 0.5 second between the remote control button is pressed and the relay is activated.
It is not permitted to dispose of waste equipment together with other waste. Dispose only in specially designated
areas. The household plays a key role in the recycling of waste equipment. By correct sorting of waste, including
waste equipment and batteries, household members ensure that the equipment is not disposed together with
household waste, but in specially designated areas, and thus may be used again after recycling.