infa-secure 527 User manual

High/Low Chair
Assembly Instructions
For models 527, 528 and 529
P.O. Box 487, Emu Plains NSW 2750
Service No: 02 4728 8090

High chair #527, 528, 529
Assembly Instructions
Before assembly study the diagrams and read the instructions thoroughly. Identify and check
against the list below. If any parts are missing or appear to be faulty or damaged, please contact
INFASECURE Service Department on [phone].
A
B
L
O
P
GH
I
Parts List
A 2x Base
B 4x Castors
C 2x A-Frame
D 1x Mesh Basket
E 1x Footrest
F 1x Foot plate
G 2x Seat Body
H 2x Seat Cover
I 2x Seat Insert
J 1x Tray
K 1x Inner Tray
L 1x Harness
(i) RH Lap Strap
(ii) RH Shoulder Strap
(iii) Crotch Strap
(ix) LH Shoulder Strap
(x) LH Lap Strap
M 2x Screws
N 2x Washer
O 2x Large Nut
P 2x Small Nut
Q 1x Axle Rod
R 1x Cross Bar
C
FE
D
K
J
M
Q
R
N
L (i) L (x)
L (ii) L (ix)
L (iii)
2

IMPORTANT:
PLEASE READ INSTRUCTIONS
CAREFULLY. KEEP FOR
FUTURE REFERENCE.
WARNINGS
• DO NOT LEAVE CHILDREN UNATTENDED.
• FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
• THE HARNESS MUST ALWAYS BE USED AND CORRECTLY FITTED – MOST INJURIES
FROM HIGH CHAIRS ARE CAUSED BY FALLS .
• POSITION THE HIGH CHAIR AWAY FROM SOLID STRUCTURES AND BENCHES TO
AVOID INJURIES CAUSED BY FALLS AND BY ACCESS TO DANGEROUS ITEMS.
• Never allow this product to be used as a toy.
• Do not use for children weighing more than 17kg.
• Ensure the high chair is only used on safe level surfaces.
• When adjusting the chair always ensure that parts of your child’s body are clear of any
moving parts.
• Never carry or fold the high chair while the child is sitting in it.
• Do not elevate the highchair onto any structure or table.
• Check regularly for loose, worn, or torn parts and repair or replace as required with
genuine INFA spare products.
• DO NOT USE UNTIL REPAIRED.
• Do not allow other children or animals to play near or walk under the chair when in use.
• To reduce the risk of injury, position the high chair away from furniture, walls, hot surfaces
and liquids, window covering cords, and electrical cords and position the high chair away from
furniture when the chair is not being used at a table with a tray removed.
• The high chair should only be used in an upright position once the child is capable of reliably
and consistently sitting upright.
• Always apply wheel locks when not moving the high chair.
• Check that the harness is correctly tted - use this harness at all times.
• Do not use the the high chair unless all components are correctly tted and adjusted.
• Be aware of the risk of open re and other sources of strong heat, such as electric bar res,
gas res etc. in the vicinity of the high chair.
1. Remove the ‘A’ frames from the
packaging [Figure 1].
!
Figure 1
3

2. Insert cross bar into ‘A’ frames and
align the holes to allow the bolts to
pass through. Attach using nut and
washer then fasten the nut with the
appropriate tools [Figure 2]. (Tools
not supplied).
3. Press both red buttons on the rear
tubular legs and slide them down to
open the frame as shown [Figure 3].
4. To insert the castors turn the frame
upside down. Insert the four castors
into the holes provided in the plastic
bases [Figure 4].
5. Hook the seat onto the seat support
located on the top of the frame.
(Ensure that the two female slots of
the seat support are aligned with the
corresponding male slots located on
seat) [Figure 5].
Figure 2
Figure 3
Figure 4
Figure 5
4

6. Secure the seat to the ‘A’ frame by
sliding the axle rod through the seat
support and aligned seat [Figure 6].
Attach nuts to each end to hold the
rod in place.
7. To attach the basket loop the clip
straps over the seat locking bar located
under the seat [Figure 7].
8. Hook the rear straps onto the knobs
found at the rear of the seat [Figure 8].
9. To install the footrest (E) simply push it
into position using the slots provided
on the seat and the back of footrest
[Figure 9].
Figure 6
Figure 7
Figure 8
Figure 9
5

Figure 10
Figure 11
Figure 12
Figure 13
10. Position the footplate into the correct
height slots for your child [Figure 10].
11. Position cover onto seat body and
allign so that holes are accessible
[Figure 11].
12. Insert each harness part into the
alligning holes, push through until
the end plastic clip protrudes out
the back of the seat [Figure 12].
13. Make sure harness is fully assembled.
Check the hardware clicks together
[Figure 13].
6

14. To install the tray pull the release
handle located under the front of tray
and slide it onto the arms of chair
using guide provided on the underside
of tray. The tray has a three-position
adjustment mechanism and can
therefore be adjusted to three different
positions [Figure 14].
15. Tray can be hooked onto the back legs
of highchair while not in use [Figure
15].
Recline Backrest
16. To recline the backrest (three positions)
pull the backrest lever upwards to
release. Find the most suitable position
and release the lever to secure the
backrest into the required position
[Figure 16].
High/Low Positions
17. Press the two red buttons on sliding
sleeve and adjust to required height.
(Do not adjust whilst baby is seated)
[Figure 17].
Figure 14
Figure 15
Figure 16
Figure 17
7

Folding Legs
18. Before folding the highchair, rst
remove the tray and store it on the tray
hooks on the back legs of the highchair
[see Figure 15]. To fold away press the
red buttons located on the rear legs
and slide upwards to fold legs together
[Figure 18].
Folding Tray
19. To fold the tray into storage position,
press the buttons on the armrests
[Figure 19]. The seat must be in highest
position. (Do not fold the tray whilst
baby is seated).
Locking Wheels
20. Press down on red locks on each
castor to lock the wheels when in use.
Lift red lock lever to unlock the wheels.
21. The highchair is now ready for storage
or travel.
Figure 18
Figure 19
Figure 20
Figure 21
8

Congratulations. You have completed the assembly instructions. Your highchair
is now ready for use. Please read all the safety warnings on page 3 and store
instructions in a safe place.
To secure your child in the harness push buckle tongues (A) into buckle housing (B) and
adjust with waist strap adjuster so that the waist strap is rmly secured around child.
Adjust crotch strap rmly using crotch strap adjuster. Place shoulder straps in position on
buckle tongues (A) and adjust so that they are rm and comfortable on child.
Figure 22
Shoulder Strap
Adjuster
Shoulder Strap
End Clip
End Clip
End Clip
Clips
Waist Strap
Adjuster
Waist Strap
Clips
Buckle
Tongue (A)
Buckle
Housing (B)
Crotch Strap
Adjuster
Crotch Strap
9

Only use warm soapy water for cleaning. Dry immediately after. Do not leave in direct
sunlight for prolonged periods as fading may occur. Do not use abrasive cleaner or
bleach. For further enquiries please contact the Infa Service Department on
[phone].
The optional #007 booster pad is available separately to add padding to the seat and
reduce the seating area for the smaller child. This provides the child with extra security
and comfort.
We warrant this product for twelve months from the date of purchase against failure due
to manufacturing faults or faulty materials. Misuse, accidental damages, normal wear and
tear are not covered by this warranty. When used for commercial use the period is limited
to six months. “Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.”
CARE AND CLEANING
WARRANTY DETAILS
TO USE FOR A SMALLER BABY
10

Head Office And Registered Address:
www.infasecure.com.au
INFASECURE PTY LTD
Phone: [phone]
Customer Service Phone: [phone]
Fax: [phone]
110-114 Old Bathurst Rd, Emu Plains, NSW, 2750
P.O Box 487, Emu Plains, NSW, 2750
ISSUE A
ABN: 52 149 173 660