infa-secure Cosmo User manual

Cosmo
Change Centre
INSTRUCTIONS
MODEL# CT50
IMPORTANT: Please read
instructions carefully. Keep these
instructions for future reference.
P.O. Box 487, Emu Plains NSW 2750
Service No: 02 4728 8090
OPERATING INSTRUCTIONS
NOTE:
when using the
bath, care should be
taken that the water
is of a suitably safe
temperature before
placing the child in.
Do not use the bath
without the frame.
Always apply press
studs (o) while
changing mat is
hanging.
The changing station
is now complete,
please read the
user guide notes to
maintain the unit to
the highest standard.
(o)
WARNING:
Never leave the
child unattended.
MAX AGE:
12 Months.
33cm
(
o
)

✗✓
We reserve the right to alter this product without notice. www.infasecure.com.au
ISSUE A
InfaSecure Warranty Details
InfaSecure Pty Ltd warrants this product for twelve months from the date of
purchase against failure due to manufacturing faults or faulty materials. Misuse,
accidental damages, normal wear and tear are not covered by this warranty.
When used for commercial use the period is limited to six months.
“Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.”
SAFETY WARNINGS
• Do not leave a child unattended when changing or bathing
• The drainage hose should be permanently attached to the bath tub drainage outlet or
stored out of the reach of children.
• Keep this product away from re and direct heat sources.
• Regularly check the screw ttings for tightness and security and adjust where necessary.
• Always apply press studs while changing mat is hanging.
• Do not use the changing station if any parts are broken or missing.
• Do not move the changing station when using as a baby changer.
• Do not use the change centre in a manner which it was not designed for.
• Assemble the dresser once. It is not designed to be taken apart and re-assembled.
• Lockable castor/wheels are tted, they shall be locked when the changing unit
is in use.
• The weight of the child should not exceed 14 kgs.
CARE AND MAINTENANCE
• Never clean with abrasive, ammonia based, bleach or spirit type cleaners.
• Use only warm water and mild soap for cleaning.
6. The changing unit’s bath tub comes complete with a handy drainage hose (k) which
can be attached to the outlet on the underside of the bath.
Before placing water in the bath, ensure the plug (l) is rmly located in the plug hole
on the inside of the bath.
USING THE BATH
INFASECURE PTY LTD
ABN: 52 149 173 660
Head Office and Registered Address:
110-114 Old Bathurst Rd, Emu Plains, NSW 2750
P.O. Box 487, Emu Plains, NSW, 2750
Phone: [phone]
Fax: [phone]
Customer Service phone: [phone]

OPERATING INSTRUCTIONS
Figure 1
IMPORTANT: Before assembling this product, study the parts list and Figure 1.
PARTS LIST
(a) Left panel
(b) Right panel
(c) Side Frames
(d) Padded top + frame + hinge
(frame & hinge to be attached)
(e) Base shelf
(f) Bath tub
(g) Pan trays
(h) Utility holders
(i) Wheels
(j) Bolts
(k) Drainage pipe
(l) Plug
(m) Tool
(n) Mesh bag
(not shown)
(o) Stud
(not shown)
Thank you for choosing an InfaSecure product. Please take a little time to read the
important safety notes detailed below. This will ensure many years of happy, safe use.
hin
g
e
ta
ched
)
(a)
(d)
(b)
(e)
(f)
(g) x3 (h) x2
(k) (l) (m)
(i) x4 (j) x12
(c) x2
Unpack the changing unit carefully and unwrap each part taking care not to lose
the plastic bag of small items. Check the contents against the list of parts.
OPERATING INSTRUCTIONS
1. Attach the two side fames (c) to the left side panel (a) by inserting bolts (j) through
the holes in the side panel and tightening into the threaded ends of the side frames
using the supplied tool (m). Attach the right hand side panel (b) in the same fashion.
ASSEMBLY
2. Lay the ‘Padded Top’ face down on a clean protective surface, and place the wire
U-shaped ‘Hinge’ in position (with eyelets towards the lifting ap). Now place the
two plastic keepers over the hinge, in the position shown, and then insert the four
screws supplied. The ‘Support Frame’ may now be tted between the hinge
eyelets, with the two plastic stems adjacent to the lifting ap but protruding away
from the bottom surface of the padded top. Turn the changing unit on its side as
shown and attach the padded top (d); insert two bolts into the tubing of the padded
top support frame. Before fully tightening the bolts, slip the elastic loops of the
mesh bag (n) over the bolt heads then tighten. Carefully turn the changing unit over
and secure the opposite side with two more bolts.
OPERATING INSTRUCTIONS
5. Attach the utility holders (h) by hooking them over the front of the support frame for
the padded top (d). Attach pan trays (g) by hooking each tray over the tops of the
two side frames (c) as shown overleaf. Finally the bath (f) can be placed in the top
of the changing unit.
3. Attach the wheels (f) to all four corners of the changing unit, pushing the wheels
rmly into place along the slots provided.
4. Attach the base shelf (e) by placing the shelf in position then securing with aps (xx)
wrapped around the uprights of the two side frames (c) and then with aps (yy)
wrapped and under the bottom of the frames .
(xx) (xx)
(xx)
(yy)
(yy)
Children have DROWNED while using
bath aids. This is NOT a safety
device. ALWAYS keep baby within
arm’s reach. NEVER leave
baby in care of children.
plastic stemslifting tab
support frame
plastic keeper & screws
hinge eyelets
NOTE: Ensure the wheels are locked
when using the changing unit
PARTS ASSEMBLY (CONT.)