Infinity Marquee 15 x 100 Manual

QTY SIZE COLOR Style QTY Style
2 14' 4" Red Spreader 2 End T's
30 9' 4" White Spreader 2 Left Corners
22 7' 8" Black Hip Rafter 2 Right Corners
22 7' 8" Black Legs 18 Regular T's
9 Spreader T
22 Ropes
130 Tent Pins
* NOTE * A 15 x 30 Marquee is
Shown. The Tent is Expandable to any 1 Brace Package
length. All You have to do is add 22 Weights / Stakes
3 - 9'4" pipes, 2 - 7'8" pipes, 1- Spreader T, 22 Ratchets
2 - Regular T's, and 2 - 7-8" Legs to 22 Baseplates
each Middle.
Pre-Site Inspection- Call your local utitlity companies prior to installation for any underground obstructions.
1. Layout the frame parts in the estimated location peertaining to the diagram. The spreader pipe is placed out to form
the perimeter, and the rafters are laid in the interior location.
2. Begin with a marquee End T. Attach the hip rafters (7'8" black) to the End T by sliding the pole in or ( 1' vs. 2" Pipe)
over the fitting and lining up the holes in the pole with those in the fitting. Place a pin in the first hole to secure the pole
in place.
3. Attach a spreader (9’4” white) from the first End T. Attach the rafters from the Spreader T. Now attach
another spreader from the Spreader T to the next spreader t and so on. The attach to the second End T and then attach
4. Attach the marquee right and left corner fitting to the hip rafters by sliding the pole over the fitting. Line up the hole of the
pole with those of the fitting and place a pin.
5. Now, the perimeter is ready for assembly. Connect the corners to the corners and the regular t's to the corners using the
spreaders (9’4” white). Slide the poles over the fitting, line up the holes, and pin the pole and fitting together. When all of
the spreaders have been secured in place, the frame will be complete.
OMIT next step if 1 Piece Top
Lay the middle sections on the ground top side up. Velcro the middle sections together, then velcro the vinyl triangle ends
to the middle.
6. Place the tent over the frame, by spreading the tent out on one end and “flapping” the tent top while pulling it over the
top. This, flapping, will make it easier to go over the frame and prevents any snags.
7. Secure the tent to the frame by fastening the straps on the inside of the tent at each corner location.
8. Start at one corner and manually lift the frame so that the leg (7' 8" black) can slide in or over the corner fitting. Pin the leg
to the fitting. ( When raising the tent, raise INTO the wind)
9. Proceed to work your way around the tent putting one leg in at a time until all legs are standing and pinned.
15 x 100 Marquee Instructions page 1 of 2
End "T"
Optional Items
Infinity Tent Sales
15 x 100 Marquee Tent Set Up Instructions
ComponentsPipe
Right
Corner
Left
Corner
Spreader T
Regular T
7'8"
7'8"

10. Now that the frame is standing, fasten the tent top completely to the frame, using the straps on the inside of the tent.
Make sure that all of the straps are tight and that the tent top is sitting evenly over the frame.
11. Fasten either a ratchet strap or rope to the fitting at each leg location. Drive a stake approximately four feet out from
each leg.
12. Attach the anchoring device (ratchets or ropes) to the stakes at each leg location.
The tent is nopw complete
15 x 100 Marquee Instructions page 2 of 2



