infobit BV40 User manual

What is content in package ?
Remote control’s funcons
①Video conference camera * 1
②User’s manual * 1
③Expansion mics * 1-3
④Charging tray * 1-2
⑤Bracket and screws * 1
⑦Power supply of the camera * 1
⑧Power supply of the charging tray * 1-2
⑨USB - type C cable * 1-2
⑩Remote control (no baery) * 1
Note: If the remote control is not available, maybe the baeries ran out. Please
change the new baeries(AAA*2pcs) .
Speakerphone mute
6Speakerphone mute
Volume up/down
7“+” volume up; “-” volume down
Buons Funcons
Camera funcons’
menu
4Camera funcons’ menu (center)
EPTZ control (up, down, le, right)
Power on/off
1Power on/off
Zoom out
2Camera zoom out
Zoom in
3Camera zoom in
Microphone mute
5Microphone mute
4
1
7
6
2
5
3
Lens
DC IN 12V Power supply interface
Camera Scroll wheel
Adjust ±15 degrees of the lens
go up and down.
Funcons LEDs indicator
The indicator lights up when using the device.
Funcons of the buons on the top
Microphone mute
2
Connecon indicator
1
Speakerphone mute
3
Volume down
4Volume up 5Power on/off 6
Buons Funcons
Power on/off
2Press 3 seconds to power on/off
Copper ring
3
When using the charging tray, the charging
copper ring acts as the charging interface.Charging
copper ring contacts spring probe for charging
Mute Microphone
1Microphone mute
Controls and Funcons
BV40 Video Conference Camera with Expansion Microphone(s)
< Front View >
< Rear View >
< Wireless Expansion Microphones.Top View(le), boom View(right) >
For connecng USB3.0 Cable
2Power on/off
3Copper ring
Mute Microphone
1
Orange LED lights
Microphone mute
2All the mics mute
Orange LED lights
Speakerphone mute
3Speakerphone mute
Blue LEDs decrease
progressively
Volume down
4Volume down
Blue LEDs increase
progressively
Volume up
5Volume up
Blue LED lights
Blue LED off
Press 3 seconds to power on
Press 3 seconds to power off
Power on/off
6
Orange LED lights
Blue LED flashes
Connecon indicator
1Connected to PC successfully via USB
Disconnected
Buons Indicator status Funcons
For LAN
( 4K )
Speakerphone mute
< Top View >
Red LED flashes Low baery
Baery Charging me Standby me Working me
VB40
2) The audio output of this device use the same USB interface with video and
supports the standard UAC protocol. All the soware which supports the UAC
protocol can collect the audio of this device.
3) Daisy-chain max up to 3 wireless expansion microphones connect to main unit
via RF2.4G transmission. Each expansion microphone provides 3 meters pick up
range. To ensure the call quality and echo cancellaon effect, please do not move
the expansion microphone aer placing it on the table. At the same me,
expansion microphones need a distance at least 1 meter from the speaker.
4) The main unit has an internal auxiliary microphone for emergency use when
the expansion mics are out of power. Expansion mics are recommended for the
best call experience. When any expansion mic is turned on, the internal mic will
be automacally disabled.
2) Prompt tone ON/OFF
Prompt tone is turned on by default. Press and hold for 5 seconds to
turn ON/OFF.
3) Enable or disable the internal microphone
Press and hold for 5 seconds to enable or disable the internal mic
Combinaon Key Funcon
Pairing Wireless Microphones
Music Mode
microphone close to the main unit.
paired.
⑥USB 3.0 cable 3M * 1
main unit
4) Remote upgrade mode
(This funcon needs the support of the manufacturer, please do not use it
under normal circumstances)
Press and hold for 5 seconds to exit the upgrade mode.
Press and hold for 5 seconds to enter remote upgrade mode, only the
orange indicator of Power buon lights.
           
          

How is working in meeng rooms ?
Video instrucon
This device output video through USB. And it supports standard UVC protocol. All
the soware which support the UVC protocol can collect the video of this device.
2) If the frame rate is not enough, the user can check whether the “ Use Frame
Rate” is cked off. If yes, please cancel the ck
❶ Open the AMCAP (available in
the CD) and click the Devices.
Then choose the 4K UCamera
(or the similar opon)
❷ Click the Opons and choose
Preview. Then the user can
preview the video. Refer to
the right picture.
1) Demonstrate the video usage of the device with common soware AMCAP.
3) Change the different resoluon and frame.
❶ Click the Capture and then
choose Set Frame Rate
❶ Click the Opons and choose
Video Capture Pin...,
❷ In Choose Frame Rate, check
whether the “Use Frame Rate”
is cked off. If yes, please
cancel the ck. And then click
the Apply
❷ Set the different resoluon
and frame according the
user’s requirement. And
then click Apply
Cancel the ck in the frame
Click Apply
麦克风（17-USB Audio Device）
4K UCamera
Note:
③The wall mounted bracket must be flat
④The wall bracket is used in conjuncon with the bracket. The device must
install the bracket
Installaon instrucon
3Wall mount
Put the device on the table or
screen and make sure the
horizontal installaon.
Horizontal placement
❶Install the bracket at the boom of the camera according to
the .
❷Screw the bracket on the wall, refer to the following picture 1.
❸Fasten the camera with boom bracket on the wall mount, refer to the
following picture 2.
(Picture 1) (Picture 2)
2Bracket installaon
2Bracket installaon
1Desktop installaon
Screw the bracket to the screw hole at the boom of the device and ghten it.
Then the user can install a bracket at the boom of the device. The screws of
the bracket must meet the following specificaons.
φ=3mm
L=6mm
Screw specificaon
Note:
①The bracket must be installed on the flat surface.
②The screws on the bracket of the video conference camera can’t be used
on the higher place, just like the ceiling mount or paron mount. 1 microphone 2 microphones
3 microphones
Connect to the computer
❶ Connect the 12V power supply to the camera.
Connect the standard USB cable with the camera and computer or other host
computer. Refer to the following picture:
DC 12V power supply
USB 3.0/2.0 cable
LAN(H Series only)
Auto-Framing
VB40 support Auto-Framing camera control, automacally moves the lens and
adjusts the zoom to comfortably frame meeng parcipants in rooms of all
shapes and sizes.
❶ Press “Camera funcons menu”
(center), select “ Setup”
Select “ AI Funcon” to “ON”,
Auto-Framing funcon turns on.
AI “Refresh Freq” is adjustable
“Low/Mid/High”.
❷