INNOVAPLAS 9075-RGB-R User manual

for light bulb
replacement
REQUIRED FOR SKU # 9075-RGB-R
1) Assemble the step according to enclosed instructions. Keep
step dry during installation. Make sure transformer stays dry at
all times.
2) Remove the Innovaplas round cap from the step by
compressing the 2 clips at the back.
3) Insert the lighting fixture from the outside of the step.
4) Pass mounting ring through front of hole and fasten using the 2 screws provided.
5) Insert light fixture by aligning the ring and turning 1/4 turn towards left.
6) Apply locking screw. Plug it in.
IMPORTANT: Use supplied tie-wraps to attach electric cord to a post as shown.
Make sure transformer is located outside the pool.
Conforms to CSA C22.2 no.89
LIGHT FIXTURE # 9075-RGB-R
REV. 15/06/10
3 4
2
65
A
THIS GUIDE CONTAINS IMPORTANT SAFETY INSTRUCTIONS.
SAVE THESE INSTRUCTIONS.
WARNING
Before installation, carefully
read the warnings and
installation instructions.
Risk of electrical shock.
Failure to follow the safety
instructions and warnings
TABLE OF CONTENTS
A) Light installation on the step.
B) Securing and instaling the
electrical cord and IR receiver.
C) Before plugging in the product.
D) Bulb replacement.
E) Winter storage.
F) Safety instructions.
LIGHT INSTALLATION ON THE STEP
TOOLS REQUIRED (Not Included)
COMPATIBLE WITH ANY INNOVAPLAS STEP
CONTAINING THE INNOVAPLAS NAMEPLATE
LIMITED WARRANTY
90 days on the water tight seal and
manufacturer defects. Replacement only.
MANUFACTURER
WARRANTY
x 3
Transformer
Receiver
Receiver
base
Remote
Light

Conforms to CSA C22.2 no.89
REV. 15/06/10
BEFORE PLUGGING IN THE LIGHT
WINTER STORAGE
SAFETY INSTRUCTIONS
CE
F
CAUTION
WARNING
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5
WWW.INNOVAPLAS.COM
Make sure the underwater portion of the power cord has been tied tightly
to the step with the tie wraps to prevent any entanglement.
Risk of electrical shock. Connect only to a grounding-type receptacle
protected by a GFCI. Do not use extension cords
for connection. Failure to do so can result in death or severe injury.
This is an electrical appliance. Unsupervised use of this product by
children can result in death or serious injury.
When plugging in the light, be certain the receptacle is GFCI
protected and a minimum of 10 feet away from the pool.
Before servicing the light unplug the power cord first.
Do not immerse the receiver.
The lighting fixture may be damaged if subjected to freezing weather.
Disconnect the 3 prong plug from the receptacle for storage.
Remove the entire step assembly from the pool and allow all water to
drain from the step and dry before storing.
Store in a dry location unexposed to winter conditions.
This light can only be installed on permanent above ground pools.
Submerge before lighting to a maximum depth of 54 inches or 1.5 meters.
To reduce risk of electrical shock, if any cord becomes damaged, return the entire transformer assembly for repair or replacement.
Risk of electrical shock. Connect only to a grounding type circuit protected by a ground fault circuit interrupter (GFCI). Contact a licensed
electrician if you cannot verify that the receptacle or circuit is protected by a GFCI. Do not use an extension cord.
Locate your pool so that the wall is at least 10 feet from all electrical receptacles and at least 20 feet from all receptacles not protected by
a GFCI.
Do not use the light if the glass lens is damaged.
Do not operate the light when not fastened to the step.
Except when the luminaire is installed in an area of the swimming pool that is not used for swimming and the lens is adequately
guarded to keep any person from contacting it, the luminaire shall be installed in or on a wall of the pool, with the top of the lens
opening not less than 457mm (18 inches) below the normal water level of the pool.
SECURING AND INSTALING THE
ELECTRICAL CORD ANS IR RECEIVER
BD
Use Innovaplas :
MCL116-12-R bulb.
Front cover
Lens O-ring
RGB light
Female
Connector
1) Firmly attach the
power cord to the rear
posts using the 2 tie
wraps provided. Make
sure the transformer
is out of the water.
2) Attach the first tie
wrap at no more than
2 inches from the
bottom of the post.
1) Orient the receiver base toward
the remote control area
and faster the base
to the pool ladge.
Water
Side
Exterior
side
2) Place the cord into the cord retainer
and secure with
a tie-wrap.
Cord retainer
1) Unplug the light.
2) To replace the bulb first remove the step
from the pool.
3) Remove stainless steel screw and turn
1/4 turn towards the right to disengage
from step.
4) Remove locking nut and screw, hold
housing firmly and unscrew the cover.
5) Remove glass lens and O-ring.
6) Replace bulb. It is strongly
recommended to change O-ring when
replacing bulb.
7) Re-assemble light fixture. Make sure not
to omit putting back locking nut and
screw.
Housing
locking nut
and screw
Tie-wraps
Tie-wraps
Water
Side
Exterior
side
BULB REPLACEMENT