INOAGE MADRIX USB ONE User manual

© 2001 – 2022 inoage GmbH |MADRIX®is a registered trademark |[email protected] |www.madrix.com
Key Features
DMX-IN/OUT With 5-Pin NEUTRIK XLR Port – This device allows you to
send or receive DMX data using 512 DMX channels. A male-to-male, 3-pin
or 5-pin XLR Gender Changer is required for DMX-IN.
Hot Swapping & Plug and Play – Devices can be connected to and
disconnected from the computer during use and without a reboot.
Power Over USB – The interface is powered directly via the USB port and
does not need an additional power supply.
Remote Control – MADRIX®5 can be controlled remotely using the
implemented DMX-IN functions.
Thank you for purchasing MADRIX®USB ONE!
Please read this manual carefully and thoroughly before using
MADRIX®USB ONE. Make sure that you fully understand all information.
Technical Specifications Package Contents
1x MADRIX®USB ONE
1x This technical manual / quick start guide
Please note: Check the package contents and the
condition of the interface after unpacking! Contact your
supplier if something is missing or damaged. Do not use
the device if it seems to be damaged!
Supply Of Power DC 5 V, 500 mA, Power over USB
Power Consumption ~ 55 mA during normal operation
DMX512 512 DMX channels, input or output
Plug 5-pin, XLR, female, NEUTRIK
USB 1x port, USB 2.0, type-A male plug,
Plug and Play, 2 m cable
Weight 105 g
Temperature Range 10 °C to 50 °C (Operating) | -10 °C to 70 °C (Storage)
Relative Humidity 5 % to 80 %, non-condensing (Operating / Storage)
IP Rating IP20
Certificates CE, EAC, FCC, RoHS
Warranty 5 years of limited manufacturer's warranty
MADRIX®USB ONE –
Technical Manual & Quick Start Guide
Copyright Information And Disclaimer
© 2022 inoage GmbH. All rights reserved.
Information is subject to change at any time and without prior notice. Errors
andomissionsexcepted.Reproduction,adaptation, or translationwithoutprior
written permission is prohibited. inoage GmbH does not grant guarantee on
validity for a particular reason, the marketability, or other properties of the
product. There is no way to assert a claim to inoage GmbH, neither in the legal
way nor in other ways. inoage GmbH is not responsible for damages, including
all disadvantages that are not just limited to the loss of sales, but that are
caused due to the use of the product, due to the loss of serviceability of the
product, due to misuse, happenings, circumstances, or actions that inoage
GmbH does not have influence on, no matter if the damages as well as
consequential damages are direct or indirect; whether they are special
damages or others, nor if the damage is caused by the owner of the warranty
or a third person.
1st Edition — September 2022
Limited Warranty
Five years of limited manufacturer's warranty are granted to
the purchaser of this product with regards to constructional
fault, material defect, or incorrect assembly the
manufacturer has caused or is to be held responsible for. This
warranty will be void if the interface is opened, modified, or
damaged through inappropriate handling, wrong usage,
overvoltage, or damaged through any other cause. All details
are available online at www.madrix.com/warranty
End-Of-Life
This electrical device and its accessories need
to be disposed of properly. Do not throw the
device into normal trash or household waste.
Please recycle packaging material whenever possible.

© 2001 – 2022 inoage GmbH |MADRIX®is a registered trademark |[email protected] |www.madrix.com
1] Connect your device.
2] Enable drivers in the MADRIX®5 Software.
3] Activate the device in the MADRIX®5 Device Manager.
1] Connect Your Device
�Connect your DMX line to the 5-pin, female XLR connector of MADRIX®USB ONE.
�If you want to use DMX-IN, please use a 5-pin XLR male to 5-pin XLR male gender changer.
�Connect your MADRIX®USB ONE to a free USB 2.0 port of your computer.
�Make sure that the Microsoft®Windows®operating system recognizes the device.
Windows®will automatically install the drivers for the device.
2] Enable Drivers In The MADRIX®5 Software
�In MADRIX®5, go to the menu 'Preferences' > 'Options...' > 'Devices USB'.
�Activate 'MADRIX USB ONE / MADRIX NEO'.
[The option is activated by default.]
�Click 'Apply' and 'OK'.
3] Activate The Device In The MADRIX®5 Device Manager
The MADRIX®USB ONE allows you to send [DMX-OUT] or receive [DMX-IN] data via MADRIX®5 using 512 DMX channels.
�In MADRIX®5, go to the menu 'Preferences' > 'Device Manager...' > 'DMX Devices'.
�Or press 'F4'.
�Select your device in the list.
�Right Mouse Click or Left Mouse Double-Click on the column 'State' to set from 'Off' to 'On' [indicated by green light].
�A] Right Mouse Click or Left Mouse Double-Click on the column 'OUT / IN' to set to 'OUT' for data output.
�B] Right Mouse Click or Left Mouse Double-Click on the column 'OUT / IN' to set to 'IN' for data input if you wish to receive incoming
data through this device.
�When using your device as an output device, set up the correct DMX universe.
�Right Mouse Click or Left Mouse Double-Click on the column 'Universe' and enter the required number.
For more information, see the MADRIX®5 User Manual.
Step-By-Step Configuration
Support
In case of further questions concerning handling of MADRIX®USB ONE or
technical problems, use the following resources for troubleshooting:
– Read the MADRIX®5 User Manual
– Contact your dealer
– Have a look at the website and online forum at www.madrix.com
– You can also directly contact [email protected]
Imprint
inoage GmbH
Wiener Straße 56
01219 Dresden
Germany
Web www.madrix.com
E-mail [email protected]
Phone [phone]
MADRIX®USB ONE –
Technical Manual & Quick Start Guide