Inscale IN301 User manual

IN301 STATISTICS
PRINTER
OPERATOR’S MANUAL
Inscale Measurement Technology Ltd
Tel: Fax:Email:
[phone] [phone] [e-mail]
7 Heron Close, St. Leonards-on-Sea. East Sussex TN38 8DX United Kingdom
Http:www.inscale-scales.co.uk
Solutionsin Weighing Technology
Inscale Measurement Technology Ltd follows a policy of continuous improvement and reserves the right to change specifications without notice. © October 2002

©Inscale 2000
Manufacturer’s Declaration of Conformity
This product has been manufactured in accordance with the harmonised European standards,
following the provisions of the below stated directives:
Electro Magnetic Compatibility Directive 89/336/EEC
Low Voltage Directive 73/23/EEC
Inscale Measurement Technology Ltd.
7 Heron Close
St.Leonard-on-Sea
East Sussex TN38 8DX
United Kingdom
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. The
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Shielded interconnect cables must be employed with this equipment to insure compliance with the
pertinent RF emission limits governing this device.
ChangesormodificationsnotexpresslyapprovedbyInscale couldvoidtheuser'sauthority
to operate the equipment.

IN301 PRINTERWITHSTATISTICS
TheIN301 Printerisageneralpurposethermotallyroll printerspecificallydesigned
toworkwiththe Inscale seriesofbalances.
ThePrinterwithStatisticsallowsthe usertocollectdatafromInscale balancesand
then print statistical information about the data. Alternately it can be set as a standard
printer to collect but without the statistics.
The printer comes preset to work with the default RS-232 interface found on the
Inscale balances. It caneasilybechanged toworkasastandardprinterwithother
equipment.
The printer is easy to use with only a paper feed button (grey button) and a print switch
(red button). ThePrint switchsendcommandstorequestdatafromInscale
balances.

©Inscale 20002
SPECIFICATIONS
Power Supply 8.5 to 14VDC or 7 to 10VAC
15 Watts when printing
3 Watts when idle
Mains Supply As required
Standard adapters are
230VAC 50/60Hz (UK or European)
or
115VAC 50/60Hz USA
Environment 5 to 35ºC
10 to 80% humidity,
non-condensing
Printer Dot matrix Thermo printer
Bi-directional printing
0.75 lines per second
40 or 80 characters per line
Paper 112mm thermo paper
PH65 or HONSHU Standard
20 meter roll
maximum diameter 48mm.
Size 60 x 180 x 150mm
0.6kg
Interface RS-232 or RS-242 (TTL)
5 pin DIN Connector
1200, 2400, 4800 or 9600 baud
8 bit or 7 bit
With or without parity

©Inscale 20003
PAPER LOADING
See diagram. Cut paper at angle and feed into slot from rear. Press and hold the Paper
Feed button until the paper passes through the printer. Do not pull paper or force
through the slot. If the paper does not feed easily check you are using the paper entry
slot and there are no obstructions in the paper path.
Paper Loading
Note direction of paper roll
Configuration
Dip-Switch

©Inscale 20004
CONFIGURATION
The printer is set with the dip-switches under the paper roll, see drawing on page 3.
Whenconfiguredasastatisticsprinterit willworkwiththeInscale balancesonly.
The data from the balances will be collected and statistical information on the readings
from the balance can be printed. The data and time can also be printed with the data.
When the printer is set for standard printing it can be used with most RS-232 devices to
print the data from them. The data and time are not available.
To reset the parameters turn the printer off. Set the switches as desired and then turn
the printer on.
With SW8 Off With SW8 On*
Statistics disabled Statistics enabled
1200 2400 4800 9600baudSelect Inscale Balances*
SW1 on off on off Off
SW2 on on off off Off
SW3 On 8 bit data not used
Off 7 bit data
SW4 On Check Parity Increment number*
Off No Parity check Do not print number
SW5 On Parity Even Data/time enabled*
Off Parity Odd Data/Time not printed
SW6 On 80 column Print all statistics*
Off 40 column Print only number of readings
and total
SW7 On High Quality Print (slow) High Quality Print (slow)
Off Normal Print (fast) Normal Print (fast)*
*The default settings are:
OperatewithInscale balancesforstatistics
4800 baud Date and time enabled 40 column
8 bit Line numbering enabled
no parity Fast printing enabled

©Inscale 20005
INTERFACE
Cable between printer and balances
PrinterInscale Balances
5 pin DIN connector. 9 Pin D-Subminiature Socket
Pin 1 RXD ----------- Pin 3 Data from Scale
Pin2DTR-----------Pin1NotusedbyInscale balances
Pin 3 GND ----------- Pin 5 Signal ground
Pin 4 nu
Pin 5 TXD ----------- Pin 2 Data to scale
Pin 7 Connected to Pin 8
Pin 4 Connected to Pin 6

©Inscale 20006
STATISTICS OPERATION
The printer has 2 switches to assist in printing statistical information for data received
from balances. The Paper Feed switch (Grey button) normally advances the paper. In
addition the printer has another switch, PRINT (Red button) that is used to send the
Print command to balances and in conjunction with the Paper Feed for some
operations.
When power is turned on the Statistics function is automatically enabled if SW8 is ON.
Send data to the printer from the scale by pressing the PRINT key on the printer,
pressing the PRINT key on the scale or setting the scale to automatically print when
stable.
During data collection the last data can be erased if in error by pressing the PF then
PRINT switch in sequence.
Continue to collect data in this manner. At any time data collection can be stopped by
holding down Paper Feed and then pressing PRINT and releasing both buttons.
A message showing the options is displayed.
PRINT Press PRINT to get a Statistics Report
PRINT + PF Start a new Series by holding PRINT then pressing the
Paper Feed switch
PF + PRINT Continue by holding Paper Feed then pressing the
PRINT switch
The Statistics Report consists of the following information.
n = number of results
sum x = sum of all results
x = average
s = standard deviation (n-1)
srel = relative standard deviation
min = minimum value
max = maximum value
R = range (max – min)
The equations used are:
()
2
1−
−
=
n
xx
si
x
s
srel =

©Inscale 20007
During the time the data collection is suspended the printer can be used for normal
printing as long as the RS-232 settings are 4800 baud, no parity, 8 bit.
Hold Paper Feed + press PRINT to continue with the data collection procedure or hold
PRINT then press Paper Feed to start a new set of data collection.
If the printer detects a change in format or an error during data collection a message of
* Data Error * will be printed. If the message does not clear when the balance data is
sent to the printer it may be necessary to turn the printer off/on before starting again.

©Inscale 20008
NORMAL PRINTING
If the printer is changed to perform as a normal serial printer (SW8 OFF) then the
setting of the other switches will need to be changed to match the baud rate, parity and
other printer settings.
Turn power off when setting the switches and the new parameters will become active
when the power is turned back on.
The printer generally uses the IBM Proprinter commands, with additional special codes
to print the date and time.
ESC c or ESC C Print current time
ESC d or ESC D Print current date
SETTING DAY AND TIME
Hold the Feed key down when power is turned on. The printer will go into a date/time
setting mode. Regardless of internal switch settings proceed as follows.
An ASCII string must be sent to the printer to set the date and time. One method of
doing this is to connect the printer to a PC or other terminal device. Send the following
commands to the printer from the DOS prompt.
C:\> MODE COMx:1200,E,7,1<enter>
C:\> COPY CON COMx<enter>
C:\> Tyy;mm;dd;hh;mm;ss<enter>
C:\> CTRL-Z<enter>
Comx is the active Com port the printer is connected to. For example to set 18 May
1999, 9:25 AM send T99;05;18;09;25;00<enter> CTRL-Z<enter> then turn power off
then back on to begin normal operation. The baud rate and parity should be as set
above regardless of how the printer is configured using the dip-switches.
AprogramtosetthedateandtimeisavailablefromInscale.Thisprogramwill
rununderWindows.Contactus fordetails.

©Inscale 2000
©CopyrightbyInscale Measurement Technology Ltd.All rightsreserved.
No part of this publication may be reprinted or translated in any form or
byanymeanswithout thepriorpermissionofInscale.
Inscale reservestheright tomakechangestothetechnology,
features, specifications and design of the equipment without notice.
All information contained within this publication was to the best of our
knowledge timely, complete and accurate when issued. However, we are
not responsible for misimpressions which may result from the reading of dated material.
The latest version of this publication can be found at our Website
(see below)
Inscale Measurement Technology Ltd.
7 Heron Close, St.Leonards-on-Sea
East Sussex, TN38 8DX, U.K.
Email:[e-mail]
Website:http://www.inscale-scales.co.uk