Inscape Data LinkPower LPS1800 Series User manual

LinkPowerLPS1800 Series
IP Management User’s Manual
May, 2015
Corporate Headquarters
Inscape Data Corporation
1620 Oakland Road D101
San Jose, CA 95131
U.S.A.
Website: http://www.inscapedata.com
Main: 408 392-9800
Fax: [phone]

Page 2
Revision 1.0
Certification
Inscape Data Corporation certifies that this product met its published specifications at time of shipment
from the factory.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
The user is cautioned that changes and modifications made to the equipment without approval of the
manufacturer could void the user's authority to operate this equipment.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.
Industry Canada Statement
This ClassA digital apparatus complies with Canadian ICES-003.
CE Statement
This product complies with the European Low Voltage Directive 73/23/EEC and EMC Directive
89/336/EEC as amended by European Directive 93/68/EEC.
Warning: This is a class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Page 3
Revision 1.0
Limited Warranty and Disclaimer of Warranty
Hardware. Inscape Data Corporation, or subsidiary selling the Product (“Inscape Data”) warrants that
commencing from the date of shipment to Customer (and in case of resale by a Inscape Data’s reseller,
commencing not more than ninety (90) days after original shipment by Inscape Data), and continuing
for a period of the longer of (a) ninety (90) days or (b) the period set forth in the warranty card
accompanying the Product (if any), the Hardware will be free from defects in material and
workmanship under normal use. The date of shipment of a Product by Inscape Data is set forth on the
packaging material in which the Product is shipped. This limited warranty extends only to the original
user of the Product. Customer’s sole and exclusive remedy and the entire liability of Inscape Data and
its suppliers under this limited warranty will be, at Inscape Data’s or its service center’s option,
shipment of a replacement within the warranty period and according to the replacement process
described in the warranty card (if any), or if no warranty card, as described on the Inscape Data Product
Warranty Policy or a refund of the purchase price if the Hardware is returned to the party supplying it
to Customer, freight and insurance prepaid. Inscape Data replacement parts used in Hardware
replacement may be new or equivalent to new. Inscape Data’s obligations hereunder are conditioned
upon the return of affected Hardware in accordance with Inscape Data’s or its service center’s
then-current Return MaterialAuthorization (RMA) procedures.
Software. The limited warranty in the United States Federal Communications Commission Notice sets
forth Inscape Data’s warranty obligations with respect to the Software.
Restrictions. The above Hardware warranty and limited warranty in the End User License Agreement
(“Software warranty”) do not apply if the Software, Hardware Product or any other equipment upon
which the Software is authorized by Inscape Data or its suppliers or licensors to be used (a) has been
altered, except by Inscape Data or its authorized representative, (b) has not been installed, operated,
repaired, or maintained in accordance with instructions supplied by Inscape Data, (c) has been
subjected to abnormal physical or electrical stress, abnormal environmental conditions, misuse,
negligence, or accident; or (d) is licensed for beta, evaluation, testing or demonstration purposes. The
Software warranty also does not apply to (e) any temporary Software modules; (f) any Software not
posted on Inscape Data’s Software Center (on InscapeData.com URL where Inscape Data makes the
Software publicly available to customers); (g) any Software that Inscape Data expressly provides on an
“AS IS” basis on Inscape Data’s Software Center; or (h) any Software for which Inscape Data does not
receive a license fee.

Page 4
Revision 1.0
DISCLAIMER OFWARRANTY
EXCEPT AS SPECIFIED IN THIS WARRANTY SECTION, ALL EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, SATISFACTORY QUALITY,
NON-INTERFERENCE, ACCURACY OF INFORMATIONAL CONTENT, OR ARISING FROM A
COURSE OF DEALING, LAW, USAGE, OR TRADE PRACTICE, ARE HEREBY EXCLUDED TO
THE EXTENT ALLOWED BY APPLICABLE LAW AND ARE EXPRESSLY DISCLAIMED BY
INSCAPE DATA, ITS SUPPLIERS AND LICENSORS. TO THE EXTENT AN IMPLIED
WARRANTY CANNOT BE EXCLUDED, SUCH WARRANTY IS LIMITED IN DURATION TO
THE EXPRESS WARRANTY PERIOD. BECAUSE SOME STATES OR JURISDICTIONS DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, THE ABOVE
LIMITATION MAY NOT APPLY. THESE WARRANTIES GIVE CUSTOMER SPECIFIC LEGAL
RIGHTS, AND CUSTOMER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
JURISDICTION TO JURISDICTION. THIS DISCLAIMER AND EXCLUSION SHALL APPLY
EVEN IF THE EXPRESS WARRANTY SET FORTH ABOVE FAILS OF ITS ESSENTIAL
PURPOSE.

Page 5
Revision 1.0
INSCAPE DATA CORPORATION
1-Year Limited Hardware Warranty Terms
The following are special terms applicable to your hardware warranty. Your formal Warranty
Statement, including the warranty applicable to Inscape Data software, appears in the End User License
Agreement that accompanies your Inscape Data product.
Duration of Hardware Warranty: One (1) Year
Replacement, Repair or Refund Procedure for Hardware: Inscape Data or its authorized service
center will use commercially reasonable efforts to ship a replacement part after receipt of the RMA
request and the RMA item. Actual delivery times may vary depending on Customer location. Inscape
Data reserves the right to refund the purchase price as its exclusive warranty remedy.
To Receive a Return Materials Authorization (RMA) Number: Please go to Inscape Data’s website
and complete the RMArequest, http://www.inscapedata.com/rma.htm.

Page 6
Revision 1.0
Inscape Data Corporation, 1620 Oakland Road, STE D101, CA95131 USA
IMPORTANT: PLEASE READ THIS END USER LICENSEAGREEMENT CAREFULLY.
DOWNLOADING, INSTALLING OR USING INSCAPE DATA OR INSCAPE
DATA-SUPPLIED SOFTWARE CONSTITUTESACCEPTANCE OF THISAGREEMENT.
INSCAPE DATA CORPORATION OR ITS SUBSIDIARY LICENSING THE SOFTWARE INSTEAD
OF INSCAPE DATA CORPORATION (“INSCAPE DATA”) IS WILLING TO LICENSE ITS
SOFTWARE TO YOU ONLY UPON THE CONDITION THAT YOU ACCEPT ALL OF THE
TERMS CONTAINED IN THIS END USER LICENSE AGREEMENT PLUS ANY ADDITIONAL
LIMITATIONS ON THE LICENSE SET FORTH IN A SUPPLEMENTAL LICENSE AGREEMENT
ACCOMPANYING THE PRODUCT (COLLECTIVELY THE “AGREEMENT”). TO THE EXTENT
OF ANY CONFLICT BETWEEN THE TERMS OF THIS END USER LICENSE AGREEMENT
AND ANY SUPPLEMENTAL LICENSE AGREEMENT, THE SUPPLEMENTAL LICENSE
AGREEMENT SHALL APPLY. BY DOWNLOADING, INSTALLING, OR USING THE
SOFTWARE, YOU ARE BINDING YOURSELF AND THE BUSINESS ENTITY THAT YOU
REPRESENT (COLLECTIVELY, “CUSTOMER”) TO THE AGREEMENT. IF YOU DO NOT
AGREE TO ALL OF THE TERMS OF THE AGREEMENT, THEN INSCAPE DATA IS
UNWILLING TO LICENSE THE SOFTWARE TO YOU AND (A) YOU MAY NOT DOWNLOAD,
INSTALL OR USE THE SOFTWARE, AND (B) YOU MAY RETURN THE SOFTWARE
(INCLUDING ANY UNOPENED CD PACKAGE AND ANY WRITTEN MATERIALS) FOR A
FULL REFUND, OR, IF THE SOFTWARE AND WRITTEN MATERIALS ARE SUPPLIED AS
PART OF ANOTHER PRODUCT, YOU MAY RETURN THE ENTIRE PRODUCT FOR A FULL
REFUND. YOUR RIGHT TO RETURN AND REFUND EXPIRES 30 DAYS AFTER PURCHASE
FROM INSCAPE DATA OR AN AUTHORIZED INSCAPE DATA RESELLER, AND APPLIES
ONLY IF YOU ARE THE ORIGINAL END USER PURCHASER.
THE FOLLOWING TERMS OF THE AGREEMENT GOVERN CUSTOMER’S ACCESS AND USE OF
EACH INSCAPE DATA OR INSCAPE DATA-SUPPLIED SOFTWARE (“SOFTWARE”), EXCEPT TO

Page 7
Revision 1.0
THE EXTENT: (A) THERE IS A SEPARATE SIGNED CONTRACT BETWEEN CUSTOMER AND
INSCAPE DATA GOVERNING CUSTOMER’S USE OF THE SOFTWARE, OR (B) THE SOFTWARE
INCLUDES A SEPARATE “CLICK-ACCEPT” LICENSE AGREEMENT OR THIRD PARTY LICENSE
AGREEMENT AS PART OF THE INSTALLATION AND/OR DOWNLOAD PROCESS GOVERNING
CUSTOMER’S USE OF THE SOFTWARE. TO THE EXTENT OF A CONFLICT BETWEEN THE
PROVISIONS OF THE FOREGOING DOCUMENTS, THE ORDER OF PRECEDENCE SHALL BE
(1)THE SIGNED CONTRACT, (2) THE CLICK-ACCEPT AGREEMENT OR THIRD PARTY LICENSE
AGREEMENT, AND (3) THE AGREEMENT.
License. Conditioned upon compliance with the terms and conditions of the Agreement, Inscape Data
grants to Customer a nonexclusive and nontransferable license to use for Customer’s internal business
purposes the Software and the Documentation for which Customer has paid the required license fees.
“Documentation” means written information (whether contained in user or technical manuals, training
materials, specifications or otherwise) pertaining to the Software and made available by Inscape Data
with the Software in any manner (including on CD-ROM, or on-line). In order to use the Software,
Customer may be required to input a registration number or product authorization key and register
Customer’s copy of the Software online at Inscape Data’s website to obtain the necessary license key or
license file.
2
End User LicenseAgreement
Customer’s license to use the Software shall be limited to, and Customer shall not use the Software in
excess of, a single hardware chassis or card or such other limitations as are set forth in the applicable
Supplemental License Agreement or in the applicable purchase order which has been accepted by
Inscape Data and for which Customer has paid to Inscape Data the required license fee (the “Purchase
Order”). Unless otherwise expressly provided in the Documentation or any applicable Supplemental
License Agreement, Customer shall use the Software solely as embedded in, for execution on, or
(where the applicable Documentation permits installation on non-Inscape Data equipment) for
communication with Inscape Data equipment owned or leased by Customer and used for Customer’s
internal business purposes. No other licenses are granted by implication, estoppel or otherwise.
For evaluation or beta copies for which Inscape Data does not charge a license fee, the above
requirement to pay license fees does not apply.

Page 8
Revision 1.0
General Limitations. This is a license, not a transfer of title, to the Software and Documentation, and
Inscape Data retains ownership of all copies of the Software and Documentation. Customer
acknowledges that the Software and Documentation contain trade secrets of Inscape Data or its
suppliers or licensors, including but not limited to the specific internal design and structure of
individual programs and associated interface information. Except as otherwise expressly provided
under theAgreement, Customer shall have no right, and Customer specifically agrees not to:
(i) transfer, assign or sublicense its license rights to any other person or entity (other than in
compliance with any Inscape Data relicensing/transfer policy then in force), or use the
Software on unauthorized or secondhand Inscape Data equipment, and Customer
acknowledges that any attempted transfer, assignment, sublicense or use shall be void;
(ii) make error corrections to or otherwise modify or adapt the Software or create derivative works
based upon the Software, or permit third parties to do the same;
(iii) reverse engineer or decompile, decrypt, disassemble or otherwise reduce the Software to
human-readable form, except to the extent otherwise expressly permitted under applicable law
notwithstanding this restriction;
(iv) publish any results of benchmark tests run on the Software;
(v) use or permit the Software to be used to perform services for third parties, whether on a service
bureau or time sharing basis or otherwise, without the express written authorization of Inscape
Data; or
(vi) disclose, provide, or otherwise make available trade secrets contained within the Software and
Documentation in any form to any third party without the prior written consent of Inscape
Data. Customer shall implement reasonable security measures to protect such trade secrets.
To the extent required by applicable law, and at Customer’s written request, Inscape Data shall provide
Customer with the interface information needed to achieve interoperability between the Software and
another independently created program, on payment of Inscape Data’s applicable fee, if any. Customer
shall observe strict obligations of confidentiality with respect to such information and shall use such
information in compliance with any applicable terms and conditions upon which Inscape Data makes
such information available.
Software, Upgrades and Additional Copies. For purposes of the Agreement, “Software” shall include
(and the terms and conditions of the Agreement shall apply to) computer programs, including firmware,
as provided to Customer by Inscape Data or an authorized Inscape Data reseller, and any upgrades,

Page 9
Revision 1.0
updates, bug fixes or modified versions thereto (collectively, “Upgrades”) or backup copies of any of
the foregoing. NOTWITHSTANDING ANY OTHER PROVISION OF THE AGREEMENT: (1)
CUSTOMER HAS NO LICENSE OR RIGHT TO MAKE OR USE ANY ADDITIONAL COPIES OR
UPGRADES UNLESS CUSTOMER, AT THE TIME OF MAKING OR ACQUIRING SUCH COPY
OR UPGRADE, ALREADY HOLDS A VALID LICENSE TO THE ORIGINAL SOFTWARE AND
HAS PAID THE APPLICABLE FEE FOR THE UPGRADE OR ADDITIONAL COPIES; (2) USE OF
UPGRADES IS LIMITED TO INSCAPE DATA EQUIPMENT FOR WHICH CUSTOMER IS THE
ORIGINAL END USER PURCHASER OR LESSEE OR OTHERWISE HOLDS A VALID LICENSE
TO USE THE SOFTWARE WHICH IS BEING UPGRADED; AND (3) THE MAKING AND USE OF
ADDITIONAL COPIES IS LIMITED TO NECESSARY BACKUP PURPOSES ONLY.
Proprietary Notices. Customer agrees to maintain and reproduce all copyright and other proprietary
notices on all copies, in any form, of the Software in the same form and manner that such copyright and
other proprietary notices are included on the Software. Except as expressly authorized in the
Agreement, Customer shall not make any copies or duplicates of any Software without the prior written
permission of Inscape Data.
Term and Termination. The Agreement and the license granted herein shall remain effective until
terminated. Customer may terminate the Agreement and the license at any time by destroying all copies
of Software and any Documentation. Customer’s rights under the Agreement will terminate
immediately without notice from Inscape Data if Customer fails to comply with any provision of the
Agreement. Upon termination, Customer shall destroy all copies of Software and Documentation in its
possession or control. All confidentiality obligations of Customer and all limitations of liability and
disclaimers and restrictions of warranty shall survive termination of this Agreement. In addition, the
provisions of the sections titled “U.S. Government End User Purchasers” and “General Terms
Applicable to the Limited Warranty Statement and End User License Agreement” shall survive
termination of the Agreement.
Customer Records. Customer grants to Inscape Data and its independent accountants the right to
examine Customer’s books, records and accounts during Customer’s normal business hours to verify
compliance with this Agreement. In the event such audit discloses non-compliance with this
Agreement, Customer shall promptly pay to Inscape Data the appropriate license fees, plus the
reasonable cost of conducting the audit.

Page 10
Revision 1.0
Export, Re-Export, Transfer and Use Controls. The Software, Documentation and technology or
direct products thereof (hereafter referred to as Software and Technology), supplied by Inscape Data
under the Agreement are subject to export controls under the laws and regulations of the United States
(U.S.) and any other applicable countries’ laws and regulations. Customer shall comply with such laws
and regulations governing export, re-export, transfer and use of Inscape Data Software and Technology
and will obtain all required U.S. and local authorizations, permits, or licenses. Inscape Data and
Customer each agree to provide the other information, support documents, and assistance as may
reasonably be required by the other in connection with securing authorizations or licenses.
3
End User LicenseAgreement
U.S. Government End User Purchasers. The Software and Documentation qualify as “commercial
items,” as that term is defined at Federal Acquisition Regulation (“FAR”) (48 C.F.R.) 2.101, consisting
of “commercial computer software” and “commercial computer software documentation” as such terms
are used in FAR 12.212. Consistent with FAR 12.212 and DoD FAR Supp. 227.7202-1 through
227.7202-4, and notwithstanding any other FAR or other contractual clause to the contrary in any
agreement into which the Agreement may be incorporated, Customer may provide to Government end
user or, if the Agreement is direct, Government end user will acquire, the Software and Documentation
with only those rights set forth in the Agreement. Use of either the Software or Documentation or both
constitutes agreement by the Government that the Software and Documentation are “commercial
computer software” and “commercial computer software documentation,” and constitutes acceptance of
the rights and restrictions herein.
Limited Warranty
Subject to the limitations and conditions set forth herein, Inscape Data warrants that commencing from
the date of shipment to Customer (but in case of resale by an authorized Inscape Data reseller,
commencing not more than ninety (90) days after original shipment by Inscape Data), and continuing
for a period of the longer of (a) ninety (90) days or (b) the warranty period (if any) expressly set forth
as applicable specifically to software in the warranty card accompanying the product of which the
Software is a part (the “Product”) (if any): (a) the media on which the Software is furnished will be free
of defects in materials and workmanship under normal use; and (b) the Software substantially conforms
to the Documentation. The date of shipment of a Product by Inscape Data is set forth on the packaging
material in which the Product is shipped. Except for the foregoing, the Software is provided “AS IS”.

Page 11
Revision 1.0
This limited warranty extends only to the Customer who is the original licensee. Customer’s sole and
exclusive remedy and the entire liability of Inscape Data and its suppliers under this limited warranty
will be (i) replacement of defective media and/or (ii) at Inscape Data’s option, repair, replacement, or
refund of the purchase price of the Software, in both cases subject to the condition that any error or
defect constituting a breach of this limited warranty is reported to Inscape Data or the party supplying
the Software to Customer, if different than Inscape Data, within the warranty period. Inscape Data or
the party supplying the Software to Customer may, at its option, require return of the Software and/or
Documentation as a condition to the remedy. In no event does Inscape Data warrant that the Software is
error free or that Customer will be able to operate the Software without problems or interruptions. In
addition, due to the continual development of new techniques for intruding upon and attacking
networks, Inscape Data does not warrant that the Software or any equipment, system or network on
which the Software is used will be free of vulnerability to intrusion or attack.
Restrictions. This warranty does not apply if the Software, Product or any other equipment upon which
the Software is authorized to be used (a) has been altered, except by Inscape Data or its authorized
representative, (b) has not been installed, operated, repaired, or maintained in accordance with
instructions supplied by Inscape Data, (c) has been subjected to abnormal physical or electrical stress,
abnormal environmental conditions, misuse, negligence, or accident; or (d) is licensed for beta,
evaluation, testing or demonstration purposes. The Software warranty also does not apply to (e) any
temporary Software modules; or (f) any Software for which Inscape Data does not receive a license fee.
DISCLAIMER OF WARRANTY
EXCEPT AS SPECIFIED IN THIS WARRANTY SECTION, ALL EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, SATISFACTORY QUALITY,
NON-INTERFERENCE, ACCURACY OF INFORMATIONAL CONTENT, OR ARISING FROM A
COURSE OF DEALING, LAW, USAGE, OR TRADE PRACTICE, ARE HEREBY EXCLUDED TO
THE EXTENT ALLOWED BY APPLICABLE LAW AND ARE EXPRESSLY DISCLAIMED BY
INSCAPE DATA, ITS SUPPLIERS AND LICENSORS. TO THE EXTENT AN IMPLIED
WARRANTY CANNOT BE EXCLUDED, SUCH WARRANTY IS LIMITED IN DURATION TO
THE EXPRESS WARRANTY PERIOD. BECAUSE SOME STATES OR JURISDICTIONS DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, THE ABOVE

Page 12
Revision 1.0
LIMITATION MAY NOT APPLY. THIS WARRANTY GIVES CUSTOMER SPECIFIC LEGAL
RIGHTS, AND CUSTOMER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
JURISDICTION TO JURISDICTION. This disclaimer and exclusion shall apply even if the express
warranty set forth above fails of its essential purpose.
General Terms Applicable to the Limited Warranty Statement, End User License Agreement, and
Supplemental LicenseAgreement
Disclaimer of Liabilities - Limitation of Liability. IF YOU ACQUIRED THE SOFTWARE IN THE
UNITED STATES, LATIN AMERICA, CANADA, JAPAN OR THE CARIBBEAN,
NOTWITHSTANDING ANYTHING ELSE IN THE AGREEMENT TO THE CONTRARY, ALL
LIABILITY OF INSCAPE DATA, ITS AFFILIATES, OFFICERS, DIRECTORS, EMPLOYEES,
AGENTS, SUPPLIERS AND LICENSORS COLLECTIVELY, TO CUSTOMER, WHETHER IN
CONTRACT, TORT (INCLUDING NEGLIGENCE), BREACH OF WARRANTY OR OTHERWISE,
SHALL NOT EXCEED THE PRICE PAID BY CUSTOMER TO INSCAPE DATA FOR THE
SOFTWARE THAT GAVE RISE TO THE CLAIM OR IF THE SOFTWARE IS PART OF ANOTHER
PRODUCT, THE PRICE PAID FOR SUCH OTHER PRODUCT. THIS LIMITATION OF LIABILITY
FOR SOFTWARE IS CUMULATIVE AND NOT PER INCIDENT (I.E. THE EXISTENCE OF TWO
OR MORE CLAIMS WILL NOT ENLARGE THIS LIMIT). IF YOU ACQUIRED THE SOFTWARE
IN EUROPE, THE MIDDLE EAST, AFRICA, ASIA OR OCEANIA, NOTWITHSTANDING
ANYTHING ELSE IN THE AGREEMENT TO THE CONTRARY, ALL LIABILITY OF INSCAPE
DATA, ITS AFFILIATES, OFFICERS, DIRECTORS, EMPLOYEES, AGENTS, SUPPLIERS AND
LICENSORS COLLECTIVELY, TO CUSTOMER, WHETHER IN CONTRACT, TORT
(INCLUDING NEGLIGENCE), BREACH OF WARRANTY OR OTHERWISE, SHALL NOT
EXCEED THE PRICE PAID BY CUSTOMER TO INSCAPE DATA FOR THE SOFTWARE THAT
GAVE RISE TO THE CLAIM OR IF THE SOFTWARE IS PART OF ANOTHER PRODUCT, THE
PRICE PAID FOR SUCH OTHER PRODUCT. THIS LIMITATION OF LIABILITY FOR
SOFTWARE IS CUMULATIVE AND NOT PER INCIDENT (I.E. THE EXISTENCE OF TWO OR
MORE CLAIMS WILL NOT ENLARGE THIS LIMIT). NOTHING IN THE AGREEMENT SHALL
LIMIT (I) THE LIABILITY OF INSCAPE DATA, ITS AFFILIATES, OFFICERS, DIRECTORS,
EMPLOYEES, AGENTS, SUPPLIERS AND LICENSORS TO CUSTOMER FOR PERSONAL
INJURY OR DEATH CAUSED BY THEIR NEGLIGENCE, (II) INSCAPE DATA’S LIABILITY FOR
FRAUDULENT MISREPRESENTATION, OR (III) ANY LIABILITY OF INSCAPE DATA WHICH
CANNOT BE EXCLUDED UNDER APPLICABLE LAW.

Page 13
Revision 1.0
4
End User License Agreement
Disclaimer of Liabilities - Waiver of Consequential Damages and Other Losses. IF YOU ACQUIRED
THE SOFTWARE IN THE UNITED STATES, LATIN AMERICA, THE CARIBBEAN OR
CANADA, REGARDLESS OF WHETHER ANY REMEDY SET FORTH HEREIN FAILS OF ITS
ESSENTIAL PURPOSE OR OTHERWISE, IN NO EVENT WILL INSCAPE DATA OR ITS
SUPPLIERS BE LIABLE FOR ANY LOST REVENUE, PROFIT, OR LOST OR DAMAGED DATA,
BUSINESS INTERRUPTION, LOSS OF CAPITAL, OR FOR SPECIAL, INDIRECT,
CONSEQUENTIAL, INCIDENTAL, OR PUNITIVE DAMAGES HOWEVER CAUSED AND
REGARDLESS OF THE THEORY OF LIABILITY OR WHETHER ARISING OUT OF THE USE
OF OR INABILITY TO USE SOFTWARE OR OTHERWISE AND EVEN IF INSCAPE DATA OR
ITS SUPPLIERS OR LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. BECAUSE SOME STATES OR JURISDICTIONS DO NOT ALLOW LIMITATION OR
EXCLUSION OF CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION
MAY NOTAPPLY TO YOU.
IF YOU ACQUIRED THE SOFTWARE IN JAPAN, EXCEPT FOR LIABILITY ARISING OUT OF
OR IN CONNECTION WITH DEATH OR PERSONAL INJURY, FRAUDULENT
MISREPRESENTATION, AND REGARDLESS OF WHETHER ANY REMEDY SET FORTH
HEREIN FAILS OF ITS ESSENTIAL PURPOSE OR OTHERWISE, IN NO EVENT WILL INSCAPE
DATA, ITS AFFILIATES, OFFICERS, DIRECTORS, EMPLOYEES, AGENTS, SUPPLIERS AND
LICENSORS BE LIABLE FOR ANY LOST REVENUE, PROFIT, OR LOST OR DAMAGED DATA,
BUSINESS INTERRUPTION, LOSS OF CAPITAL, OR FOR SPECIAL, INDIRECT,
CONSEQUENTIAL, INCIDENTAL, OR PUNITIVE DAMAGES HOWEVER CAUSED AND
REGARDLESS OF THE THEORY OF LIABILITY OR WHETHER ARISING OUT OF THE USE
OF OR INABILITY TO USE SOFTWARE OR OTHERWISE AND EVEN IF INSCAPE DATA OR
ITS SUPPLIERS OR LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
IF YOU ACQUIRED THE SOFTWARE IN EUROPE, THE MIDDLE EAST, AFRICA, ASIA OR
OCEANIA, IN NO EVENT WILL INSCAPE DATA, ITS AFFILIATES, OFFICERS, DIRECTORS,
EMPLOYEES, AGENTS, SUPPLIERS AND LICENSORS, BE LIABLE FOR ANY LOST
REVENUE, LOST PROFIT, OR LOST OR DAMAGED DATA, BUSINESS INTERRUPTION, LOSS

Page 14
Revision 1.0
OF CAPITAL, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR PUNITIVE
DAMAGES, HOWSOEVER ARISING, INCLUDING, WITHOUT LIMITATION, IN CONTRACT,
TORT (INCLUDING NEGLIGENCE) OR WHETHER ARISING OUT OF THE USE OF OR
INABILITY TO USE THE SOFTWARE, EVEN IF, IN EACH CASE, INSCAPE DATA, ITS
AFFILIATES, OFFICERS, DIRECTORS, EMPLOYEES, AGENTS, SUPPLIERS AND LICENSORS,
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES
OR JURISDICTIONS DO NOT ALLOW LIMITATION OR EXCLUSION OF CONSEQUENTIAL
OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT FULLY APPLY TO YOU.
THE FOREGOING WAIVER SHALL NOT APPLY TO ANY LIABILITY ARISING OUT OF OR IN
CONNECTION WITH: (I) DEATH OR PERSONAL INJURY, (II) FRAUDULENT
MISREPRESENTATION, OR (III) INSCAPE DATA'S LIABILITY IN CONNECTION WITH ANY
TERMS THAT CANNOT BE EXCLUDED UNDERAPPLICABLE LAW.
For all countries referred to above, Customer agrees that the limitations of liability and disclaimers set
forth herein will apply regardless of whether Customer has accepted the Software or any other product
or service delivered by Inscape Data. Customer acknowledges and agrees that Inscape Data has set its
prices and entered into the Agreement in reliance upon the disclaimers of warranty and the limitations
of liability set forth herein, that the same reflect an allocation of risk between the parties (including the
risk that a contract remedy may fail of its essential purpose and cause consequential loss), and that the
same form an essential basis of the bargain between the parties.
Controlling Law, Jurisdiction. If you acquired the Software in the United States, Latin America, or the
Caribbean, the Agreement and Hardware and Software warranties (“Warranties”) are controlled by and
construed under the laws of the State of California, United States of America, notwithstanding any
conflicts of law provisions; and the state and federal courts of California shall have exclusive
jurisdiction over any claim arising under the Agreement or Warranties. If you acquired the Software in
Canada, unless expressly prohibited by local law, the Agreement and Warranties are controlled by and
construed under the laws of the Province of Ontario, Canada, notwithstanding any conflicts of law
provisions; and the courts of the Province of Ontario shall have exclusive jurisdiction over any claim
arising under the Agreement or Warranties. If you acquired the Software in Europe, the Middle East,
Africa, Asia or Oceania (excluding Australia), unless expressly prohibited by local law, the Agreement
and Warranties are controlled by and construed under the laws of England, notwithstanding any
conflicts of law provisions; and the English courts shall have exclusive jurisdiction over any claim

Page 15
Revision 1.0
arising under the Agreement or Warranties. In addition, if the Agreement is controlled by the laws of
England, no person who is not a party to the Agreement shall be entitled to enforce or take the benefit
of any of its terms under the Contracts (Rights of Third Parties) Act 1999. If you acquired the Software
in Japan, unless expressly prohibited by local law, the Agreement and Warranties are controlled by and
construed under the laws of Japan, notwithstanding any conflicts of law provisions; and the Tokyo
District Court of Japan shall have exclusive jurisdiction over any claim arising under the Agreement or
Warranties. If you acquired the Software in Australia, unless expressly prohibited by local law, the
Agreement and Warranties are controlled by and construed under the laws of the State of New South
Wales, Australia, notwithstanding any conflicts of law provisions; and the State and federal courts of
New South Wales shall have exclusive jurisdiction over any claim arising under the Agreement or
Warranties. If you acquired the Software in any other country, unless expressly prohibited by local law,
the Agreement and Warranties are controlled by and construed under the laws of the State of California,
United States of America, notwithstanding any conflicts of law provisions; and the state and federal
courts of California shall have exclusive jurisdiction over any claim arising under the Agreement or
Warranties.
For all countries referred to above, the parties specifically disclaim the application of the UN
Convention on Contracts for the International Sale of Goods. Notwithstanding the foregoing, either
party may seek interim injunctive relief in any court of appropriate jurisdiction with respect to any
alleged breach of such party's intellectual property or proprietary rights. If any portion hereof is found
to be void or unenforceable, the remaining provisions of the Agreement and Warranties shall remain in
full force and effect. Except as expressly provided herein, the Agreement constitutes the entire
agreement between the parties with respect to the license of the Software and Documentation and
supersedes any conflicting or additional terms contained in any Purchase Order or elsewhere, all of
which terms are excluded. The Agreement has been written in the English language, and the parties
agree that the English version will govern.
© 2007, 2008, 2009, & 2012 Inscape Data Corporation, All rights reserved.

Page 16
Revision 1.0
Safety Summary
The following general safety precautions must be observed during all phases of operation of this
instrument. Failure to comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and intended use of the instrument. Inscape
Data Corporation assumes no liability for the customer’s failure to
comply with these requirements.
BeforeApplying Power
Verify that the product is set to match the available line voltage and all safety precautions are taken.
Over Temperature Warning
To prevent the switch from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of (70°C). To prevent product cooling restriction, allow at least 3
inches (7.6 cm) of clearance around the product after installation.
Ground the Instrument
To minimize shock hazard, the instrument chassis and cabinet must be connected to an electrical
ground. The instrument must be connected to the ac power supply mains through a three-conductor
power cable, with the third wire firmly connected to an electrical ground (safety ground) at the power
outlet. For instruments designed to be hard-wired to the ac power lines (supply mains), connect the
protective earth terminal to a protective conductor before any other connection is made. Any
interruption of the protective (grounding) conductor or disconnection of the protective earth terminal
will cause a potential shock hazard that could result in personal injury.
When installing the unit, always make the ground connection first and disconnect it last.
Jewelry Removal Warning
Before working on equipment that is connected to power lines, remove jewelry (including rings,
necklaces, and watches). Metal objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals.
Do not Operate in ExplosiveAtmosphere

Page 17
Revision 1.0
Do not operate the product in the presence of flammable gases or fumes.
Chassis Power Connection
Before connecting or disconnecting ground or power wires to the chassis, ensure that power is removed
from the device. To ensure that all power is OFF, locate the circuit breaker on the panel board that
services the device, switch the circuit breaker to the OFF position, and tape the switch handle of the
circuit breaker in the OFF position.
Work During LightningActivity
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Comply with Local and National Electrical Codes
Installation of the equipment must comply with local and national electrical codes
Do Not Exceed Input and Output Ratings
Do not operate the product to exceed the power input and output ratings.

Page 18
Revision 1.0
Table of Contents
Foreword........................................................................................................20
Chapter 1 Access Device.............................................................................21
1.1 Access Method...............................................................................21
1.2 Login Configuration ........................................................................21
1.3 User Login......................................................................................21
Chapter 2 Switch Management ...................................................................23
2.1 Authentication Configuration..........................................................23
2.2 System IP Configuration.................................................................24
2.3 System Status ................................................................................24
2.4 Load Default Setting.......................................................................25
2.5 Firmware Update / Upgrade...........................................................26
2.6 Reboot Device................................................................................27
Chapter 3 Port Setting..................................................................................29
3.1 Port Configuration ..........................................................................29
3.2 Port Mirroring..................................................................................30
3.3 Bandwidth Control..........................................................................31
3.4 Broadcast Storm Control................................................................32
Chapter 4 VLAN Setting...............................................................................34
4.1 VLAN mode....................................................................................34
4.2 VLAN Member................................................................................35
Chapter 5 Port Packet Count.......................................................................37
5.1 Port Packet Count ..........................................................................37
Chapter 6 QoS Setting .................................................................................39
6.1 Priority Mode...................................................................................39
Chapter 7 Packet Security Filter .................................................................40
7.1 MAC Address Binding ....................................................................40
7.2 TCP/UDP Filter...............................................................................41

Page 19
Revision 1.0
Chapter 8 Spanning Tree Settings..............................................................42
8.1 STP Bridge Settings.......................................................................42
8.2 STP Port Settings...........................................................................43
8.3 Loopback Detection Settings..........................................................45
Chapter 9 Link Aggregation Settings.........................................................46
9.1 Link Aggregation Settings...............................................................46
Chapter 9 DHCP Relay Agent Configuration.............................................47
10.1 DHCP Relay Agent Setting.............................................................47
10.2 Relay Server Setting ......................................................................47
10.3 VLAN MAP Relay Agent Setting.....................................................47
Chapter 11 Configuration Backup/Recovery.............................................49
11.1 Configuration Backup/Recovery.......................................................49
Chapter 12 Miscellaneous ...........................................................................50
12.1 Miscellaneous Setting ....................................................................50
Chapter 13 Hardware Default Value Recovery ..........................................52
Appendix 1 Common Fault Diagnosis ...................................................53
Appendix 2 Terminology Descriptions....................................................54
Appendix 3 Network Cable Production..................................................56
RJ-45 connector ....................................................................................56
Network Cable Production.....................................................................57

Page 20
Revision 1.0
Foreword
Introduction
This manual is written for LPS1800 Managed PoE (Power over Ethernet) Switch, and all the major
functions of the fast Ethernet switch are described in detail. Through reading of this manual, you will
understand the functions of the switch’s characteristic, port Settings, VLAN, QoS Settings, and so on
various system configurations.
Reader objects
This manual requires a certain network knowledge from the user, such as understanding of a
network device and be familiar with the Ethernet equipment configuration and the role of a system
administrator.
Book Convention
Icon Description
Icon
Note Type
Description
Hint Message
The additional information for the content
Attention Message
Remind matters that should be paid attention
to during the process of operation