Insignia NS-EWF01-2 User manual

Flat size (W×H): 209.2 × 148 mm.
Final folded size: 104.6 × 148 mm.
INSTALLING THE WATER FILTER
1YOU MUST SOAK your new lter in water for 15 minutes prior to
installing it in your refrigerator to remove air from the carbon block.
2Turn o the icemaker using the power switch.
3Press the lter release button next to the old lter, then remove and
discard the lter.
4Push the new lter straight into the lter receiver until you hear two clicks.
5Turn the icemaker back on.
6 Run about two to three gallons of water through your refrigerator’s water
dispenser to remove air and loose carbon pieces. The water may be
cloudy and sputter until the air is removed.
7Reset your“change lter”indicator (if your refrigerator has one).
RESETTING YOUR CHANGE FILTER INDICATOR
Note: This is the most common lter reset instruction for the refrigerator that this
lter is made for (Electrolux). If the instruction doesn’t work for your refrigerator, see
the documentation that came with your refrigerator.
Quick Setup Guide |NS-EWF01-2
Refrigerator Filter
Before using your new product, please read these instructions to prevent any damage.
Congratulations on your purchase of one of the highest performing
water lters on the market today. Insignia lters use a high-grade
coconut carbon that has 50% more micro-pores than standard carbon.
They also use fewer high-compression binders, giving you the best
water ltration possible.
PACKAGE CONTENTS
• Refrigerator lter(s) (2 pack)
• Quick Setup Guide
GENERAL INSTALLATION GUIDELINES
• It is normal for black carbon nes (particles) to appear on the outside
of your lter. This happens when the lter is jarred in shipping. It is
safe, simply wipe it o.
• The lter connectors are larger to prevent leaks. You might have to
twist the lter hard to make sure the connection is secure.
REFRIGERATOR BRAND
Electrolux
INSTRUCTIONS
Press and hold the Filter Status button (on the
dispenser) for three seconds, until the display
changes from “Replace” to “Good”.
NS-EWF01-2_15-0328_QSG_V1_EN.ai 1 4/3/2015 5:27:57 PMNS-EWF01-2_15-0328_QSG_V1_EN.ai 1 4/3/2015 5:27:57 PM
V1
FINAL
FOR PRINT

TROUBLESHOOTING STORAGE AND MAINTENANCE
• Replace your lter every three to six months to prevent bacteria and
fungus growth in your lter, supply lines, and storage tank.
• Stored lters do not expire. Keep your unused lters in a cool, dark, and
dry place until you need them.
• If you do not use your water dispenser for more than four days, run two
gallons of water before using it to prevent bad tasting water.
ONE-YEAR LIMITED WARRANTY
For complete warranty, visit www.insigniaproducts.com.
CONTACT INSIGNIA
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
CERTIFICATIONS:
INSIGNIA is a trademark of Best Buy and its aliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2015 Best Buy. All rights reserved.
Made in China
V1 ENGLISH 15-0328
PROBLEM
My refrigerator is not
dispensing water
My water dispenser is
dripping
My water is cloudy or
contains black carbon
pieces
My new lter is making
noises or sputtering
My water tastes bad
SOLUTION
• Make sure that you soaked your lter in water
for 15 minutes before installing.
• Make sure that the lter is securely connected
to the receiver. Do not use tools to tighten the
lter in place.
• Make sure that the water line to the refrigerator
is turned on. The valve must be completely
open for the refrigerator to receive water.
• Make sure that the refrigerator door is closed or
the dispenser will not work.
• A few drops are normal. If the water is dripping
constantly, have a service technician check your
refrigerator’s water valve.
• Cloudy water is caused by microscopic air
bubbles. Run two to three gallons of water from
your dispenser to clear the air bubbles out.
• Black carbon pieces in the water are normal and
appear with all carbon lters. Run two to three
gallons of water through your dispenser to
remove loose carbon pieces.
• Make sure that you soaked your lter in water
for 15 minutes before installing.
• Noises and sputtering are caused by trapped air
pockets. Run two to three gallons of water from
your dispenser to push the air out.
• If you do not use your water dispenser for more
than four days, run two gallons of water
through the dispenser before using it.
• Make sure that you replace your lter every
three to six months to prevent bacteria growth.
COMPONENT
This NS-EWF01-2 is Tested and Certied by NSF
International against NSF/ANSI Standard 42 for materials
and structural integrity requirements.
NS-EWF01-2_15-0328_QSG_V1_EN.ai 2 4/3/2015 5:28:04 PMNS-EWF01-2_15-0328_QSG_V1_EN.ai 2 4/3/2015 5:28:04 PM