Inspired by Bassett Monaco BP-MN1379 User manual

IF PARTS ARE MISSING OR DAMAGED, DO NOT RETURN TO STORE
To order missing or replacement parts, contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
Item# BP-MN1379
MONACO BENCH
ASSEMBLY INSTRUCTIONS

LIMITED WARRANTY
INSPIRED by Bassett®Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of
5 years. Defects and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event
beyond the control of INSPIRED by Bassett®is not covered. The warranty does not cover cosmetic damage that may result from normal
use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the
customer’s responsibility to prepay freight on any components returned to the factory. INSPIRED by Bassett®will pay return freight on
components covered under terms of warranty.
WARNING
1. Do not use this product unless all screws and bolts are securely tightened.
2. Check that all screws and bolts are tight every three months or as needed.
3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
6. Intended for residential use only.
Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.

PARTS LIST
HARDWARE LIST
DRAWINGNO DESCRIPTION SIZE
A
B
C
D
E
F
QTY.
(2) Side Frame (2 PCS)
(1) Seat (1 PC)
(3) Cross Support (1 PC)
1/4’’ x 57mm 8 PCS
2 PCS
10 PCS
1 PC
Short Bolt
1/4’’ x 63mmLong Bolt
1/4’’Lock Washer
4mmAllen Wrench
2 PCSSpacer
10 PCS1/4’’ x 19mmFlat Washer

STEP 1:
STEP 2:
(3)
(B)
(D)
(E) (C)
(A)
(D) (C)
(2)
(2)
(1)
(2) (2)
Attach Cross Support (3) to Leg Frames (2) using one Spacer (E), one Flat Washer (D), one Lock Washer (C)
and one Long Bolt (B) for each end of Cross Support (3). DO NOT FULLY TIGHTEN BOLTS.
Attach Leg Frames (2) to corner blocks of Seat (1) using four Flat Washers (D), four Lock Washers (C) and four
Short Bolts (A) for each Leg Frame (2). TURN BENCH OVER TO THE UPRIGHT POSITON. APPLY FIRM PRESSURE TO
ALIGN & FULLY TIGHTEN ALL BOLTS USING ALLEN WRENCH (F).

FURNITURE CARE:
- Dust with a soft cloth following the grain pattern of the wood.
- Dust often to remove the everyday abrasive particles from the wood surfaces.
- Before dusting, moisten cloth lightly with a spray product.
- Wood finishes also benefit from an occasional polishing.
Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.