Insportline Oakland User manual

USER MANUAL –EN
IN 22637 Basketball basket inSPORTline Oakland

2
CONTENTS
SAFETY INSTRUCTIONS....................................................................................................................... 3
PARTS LIST............................................................................................................................................ 4
ASSEMBLY ............................................................................................................................................. 6
MOVING................................................................................................................................................ 12
HEIGHT ADJUSTMENT........................................................................................................................ 12
ENVIRONMENT PROTECTION ........................................................................................................... 12
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS................................................. 12

3
SAFETY INSTRUCTIONS
Please read the instruction carefully. Remove all parts and hardware from the carton and place them
on soft and clean surface. Check that nothing is missing. Please recycle all packaging materials.
•Follow the instructions carefully. Failure to follow these instructions may result in serious injury
or damage.
•Owner must ensure that all users know and follow all rules for save operation.
•Please assemble and maintain the product carefully to ensure safety.
•If you are using ladder during assembling use it with extreme caution.
•Regularly check the base for leaking. Leaks can cause the product to tip over unexpectedly.
•Seat the pole properly. Failure to do so could lead to separation of pole during transport or
play.
•Climate, corrosion or misuse could lead to injury or damage of product.
•If you need help contact customer service.
•It is recommended to fill the base with sand and not water. If you fill the base with water,
please check for leaking. Leaking can lead to tip over of the product.
•If you fill the base with water, please empty the base or add 7.57 liters of anti-freeze before the
temperature reach to or below 0 °C. Freezing water may crack the base.
•Without the base filled with water or sand, you cannot use the product. The product may tip
over and injuries or death.
•Store the basket in a horizontal position without the filled base (place it on the ground).
•Place the basket on a firm, level surface.
•Make sure the product is firmly positioned and in a stable position before use.
•The product is not a toy.
•Never use the product near water.
•Wear comfortable sports clothing during use. Always wear sports shoes.
•Do not make unauthorized modifications or modifications.
•Children may only use the product under the supervision of their parents.
•Assembly may only be carried out by an adult. Two adults are required for assembly.
•Check the condition of the product regularly. Stop using the product immediately if it is worn or
damaged.
•Use only original spare parts.
•Do not wear jewelry during use.
•Do not climb on the stand.
•Do not hang up on the hoop.
•Never throw or hang on the basket during the smash.
•Consult a physician before starting an exercise session.
•WARNING: Overextending during training can cause serious injury or death. If you feel sick,
stop exercising immediately!
•Suitable for schools and sports clubs, for indoor and outdoor use

4
PARTS LIST
No.
Specifications / Name
Picture
Qty.
A1,A2,A3,A4
M12x180 mm
1
B1,B2,B3,B4,B5
M12x180 mm
2
C1,C2,C3,C4
M12x180 mm
2
D1,D2,D3
M10x100 mm
1
E1,E2,E3
M10x90 mm
2
F1,F2,F3
M8x120 mm
2
G1,G2,G3
M8x90 mm
2
H1,H2,H3
M8x45 mm
1
I1,I2,I3
M8x45 mm
2
J1,J2,J3
M8x20 mm
2
K1,K2
M8x16 mm
2
L
Small spring
2
M
Wheels
2

5
N
Top pole cover
1
O
Cap
2
P
Mesh
1
Q
Bracket
1
R
Big spring
2
S
Board rod holder (short)
2
T
Board rod holder (long)
2
U1,U2
Pole support rods
1
V
Axle
1
W
Top pole
1
X
Middle pole
1
Y
Bottom pole
1
AA
Rim
1
BB
Base
1
CC
Board bracket
1

6
DD
Board
1
EE,FF
M12x180 mm
1
GG
Inner height adjustment rod
1
HH
Outer height adjustment rod
1
ASSEMBLY
WARNING!
Assembly can only be performed by an adult.
4 adults are recommended for installation.
Step 1
Create a post with parts W, X, Y. Attach bracket Q to the post X with bolts, washers and nuts G1, G2,
G3.

7
Step 2
Tighten the pole with a few strikes against a piece of wood.
Step 3
Connect the posts W, X and Y with bolts, washers, and nuts E1, E2, E3. Attach the wheels M to the
base BB with the axis V. Then attach the bottom post Y to the base BB. The bracket Q on the post X
must face backwards.

8
Step 4
Secure the post W, X, Y with supports U1, U2. Supports U1, U2 secure to the base BB bolts, washers,
and nuts J1, J2, J3 and to the post Y with bolts, washers, and nuts D1, D2, D3.
Step 5
Attach rim AA and board bracket CC to the board DD with bolts, washers, and nuts F1, F2, F3 and I1,
I2, I3.
Two small springs L are attach to the front of the rim AA with bolts, washers, and nuts F1, F2, F3.
Step 6
Open the board bracket CC on both sides.
Attach the board bracket to the board with bolts and washers K1, K2.
Then secure the rods S, T to the bracket CC with bolts and washers B1, B2, B3, B4, B5. Bushing B3
must be inserted in to the bracket CC.

9
Step 7
Rods S, T attach to the post W with bolts, washers, and nuts C1, C2, C3, C4.

10
Step 8
Attach outer height adjustment rod HH to the rod T with bolts, washers, and nuts A1, A2, A3, A4 as
shown. Bushing A2 must be between T and HH.
Inner height adjustment rod GG attach to the bracket Q with bolts, washers, and nuts H1, H2, H3.
Step 9
Attach bolt EE to the rods S for big springs R.
Step 10
Attach big springs R to the board holder CC and to the bolt EE.