Instant IDA-8855 User manual

Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference.
ASSEMBLY INSTRUCTION
MODEL IDA-8855

53.15"
15.74"
19.29"

▪
A B
-Top Panel x1 ▪ x 1
▪ Side Panel
Profile-L x 1
FGH
▪ Stand Panel x 2
C
▪ Side Panel - L x 1
D
▪ Side Panel - R x 1
I
- Front Leg Panel x 1 - Back Leg Panel x 1 ▪Top Crossbar x 1 - Door x 2
KLMJ
E
- Back Panel x 1
N
▪ Side Panel
Profile-R x 1

2
1
2
F
E
AC
D
B
K
J
L
C
G
1
1x30
G
!ATTENTION: DO NOT JOIN ANY PARTS IN THIS STEP!
Insert the wooden pins (1) into the corresponding holes of panels (B), (C), (D), (G), (J), (K) and (L) as
shown. Please make sure to insert them in the correct hole as some holes are intended for the cam
bolts in subsequent steps.
Attach the cam bolts (2) to the corresponding holes on panels (A), (C), (D), (E) and (F) as shown. Please
make sure to insert them in the correct hole as some holes are intended for the wooden pins in
subsequent steps.
ATTENTION: Make sure
to insert the Wooden
Pin in the correct holes,
as some other holes
are intended for the
cam bolt!”.

C
E
F
4
3
B
G
G
2
8
D
2x4
Insert and align the cam locks (2) into the corresponding holes on panels (C) and (D) as shown and as
explained on page 4. Then assemble the panel (E) to panel (C) and the panel (F) to panel (D) as explained
on page 4.
8x4
Assemble panels (B) and (G) using screws (8) as shown. Please make sure to screw thru the
correct holes on panel (B) as other holes are intended for the L-Bracket in subsequent steps.

6
5
D
J
K
L
2
2
2x2
(VIEW FROM THE BACK OF THE STAND)
(VIEW FROM THE BACK OF THE STAND)
Insert and align the cam locks (2) into the corresponding holes on panel (B) as shown and as
explained on page 4. Then assemble the panel (D) to panel (B) as explained on page 4.
Insert and align the cam locks (2) into the corresponding holes on panels (J) and (K) as shown and
as explained on page 4. Then assemble the panels (J) and (K) to panel (D/F) as explained on page
4. Finally, join the panel (L) to the panel (D/F) on the top front side of the stand, but make sure
that the holes on (L) are facing inwards, if not, they will be visible on the front of the TV stand.
2x2
B
D

11
8
7
A
2
2
11
Insert and align the cam locks (2) into the corresponding holes on panels (J) and (K) as shown and as
explained on page 4. Then assemble the panels (C/E) to the rest of the panels in this step as explained
on page 4.
2x4
Insert and align the cam locks (2) into the corresponding holes on panels (C/D/G/L) as shown and as
explained on page 4. There will be a total of 10 cam locks to insert inside the unit. Then assemble the
Top Panel (A) to the rest of the parts as explained on page 4. Finally, attach the plastic feet (11) to the
panels (C/D/E/F/K) as shown.
2x10
(VIEW FROM THE
BACK OF THE STAND)
(VIEW FROM THE
BACK OF THE STAND)
x6

N
10
9
H
I
I
10
12 13
7
6
9
Assemble the back panel (N) to the back side of the unit with nails (10) according to the illustration.
Then assemble the corner brackets (12) to the top corners of the unit using screws (13). Finally,
assemble the L brackets (6) to the panels (B/J/K) using screw (7) as shown.
7x8
6x4 10 x15
12 x2 13 x4
9x12
Place the metal pins (9) into the corresponding holes on panels (C/D/G) at the level of your
preference, and then place the shelves (I) on the 2 sides, and the shelf (H) in the center.

12
11
M
M
M
4
3
5
4
4
4
4x8
3x4 5x2
Assemble the hinges (3) to both doors (M) using screws (4) as shown. Then assemble
the handle (5) to the doors using the screws that come with the handles.
4x8
Assemble the doors to the unit using screws (4) as shown. If the door does not close
properly, ne-tune the hinges as explained in the illustration.