Insteon In-linelinc 2475s User manual

Quick-Start Guide

IN-LINELINC RELAY

In-LineLinc Relay (#2475S) - 10 Amp

SET Button

PPrreeppaarraattiioonn

IInnssttaallllaattiioonnsshhoouullddbbeeppeerrffoorrmmeeddoonnllyybbyyaaqquuaalliiffiieeddeelleeccttrriicciiaannoorrbbyyaahhoommeeoowwnneerrwwhhooiissffaammiilliiaarraannddccoommffoorrttaabblleewwiitthheelleeccttrriiccaall

cciirrccuuiittrryy..IIfftthheerreeaarreeaannyyqquueessttiioonnss,,ccoonnssuullttaanneelleeccttrriicciiaann..FFoorrsse

ettuuppqquueessttiioonnssccoonnttaaccttTTeecchhSSuuppppoorrttaattSSmmaarrttLLaabbssffoorrgguuiiddaannccee..

TToooollssyyoouuwwiillllnneeeedd::

•A Phillips screwdriver

•A wire cutter/stripper

•A voltage tester to identify wires inside the junction box

NNeeeeddHHeellpp??FFoorraassssiissttaanncceeccaallllyyoouurrffrriieennddllyy

ssuuppppoorrttppeerrssoonn@@886666--224433--88001188

Status LED

Installing Your In-LineLinc Relay

Step 1. It is recommended that you have properly installed at least two SignaLinc RF Signal Enhancers #2442 (sold separately).

Step 2. Write down the INSTEON ID and location of the fixture you want to control (e.g. 01.F7.G5, Mike’s Bedroom Light).

Step 3. At the circuit breaker or fuse panel, disconnect the power to the circuit(s) supplying power to the fixture.

Step 4. Disconnect the wires from the fixture you will be controlling and ensure you have 1/2” of bare wire on the ends.

Step 5. Follow the diagram to identify and connect the LINE, LOAD, NEUTRAL, and GROUND wires. If the colors of the wires do

not match the diagram, be sure you have identified the wires correctly before connecting them.

Step 6. Ensure that all wire connectors are firmly attached and that there is no

exposed copper except for the GROUND wire.

Step 7. Prior to reinstalling the fixture, turn the circuit breaker back on or

reinstall the fuse.

Step 8. Select the INSTEON-Enabled Controller you would like to use

to control the In-LineLinc and set it to Linking Mode. For most

controllers, press and hold the On button for 10 seconds. The

LED will begin to blink.

Step 9. Press and hold the SET Button (as pictured above) on the

In-LineLinc for 3 seconds. The Status LED will flash upon

successful linking and return to steady on. Test by pressing On

and Off on your controller. You can also use software such as

HouseLinc Desktop, which will require the INSTEON ID from

Step 2.

Step 10. Place the In-LineLinc into the junction box.

Note: Screw Tabs may be removed if not needed.

Step 11. Reinstall the fixture.

TTMM

Your new INSTEONTM In-LineLinc Relay allows you to remotely control any light or

fan in your home at the touch of a button.

•A probe that is non-conductive to press the SET Button (e.g. pencil)

Screw Tab

In-LineLinc Relay (#2475S)

Quick-Start Guide

IN-LINELINC RELAY

NNeeeeddHHeellpp??FFoorraassssiissttaanncceeccaallllyyoouurrffrriieennddllyy

ssuuppppoorrttppeerrssoonn@@886666--224433--88001188

TTooffaaccttoorryyrreesseettyyoouurrIInn--LLiinneeLLiinnccRReellaayy

1. Turn off power and wait 10 seconds.

2. Press and hold the SSEETTbbuuttttoonn, turn on power, continue holding the SET button for 3 seconds and release.

3. After several seconds, the Status LED will turn on, indicating a reset is complete.

NNootteess

•The In-LineLinc can be used with any load(s) up to 10 amps or incandescent lighting up to 400 watts.

•Software such as HouseLinc Destkop (#2416D) can make management and setup of the In-LineLinc much easier.

For detailed instructions on how to operate all the features of your In-LineLinc Relay,

please refer to the User's Guide at http://www.smarthome.com/2475s.html

Optional for X10 Users

Optional Settings

SSmmaarrttLLaabbssLLiimmiitteeddWWaarrrraannttyy

SmartLabs warrants to the original consumer of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will per-

form in substantial conformity to the description of the product in the owner's manual. This warranty shall not apply to defects or errors caused by misuse or neglect.