Intelix INT-AS2H1U-TX User manual

11675 Ridgeline Drive
Colorado Springs, CO
80921
Rev 190621 Phone: [phone]
Toll-Free: 800-530-8998
Fax: [phone]
INT-AS2H1U-TX Quick Install Guide
This guide is for quick installaon only.
For complete owners manual go to www.libav.com or use a QR reader to access the
manual via QR code below.
Scan QR Code with your Smart-phone or Tablet

INT-AS2H1U-TX Quick Guide
3
The Intelix INT-AS2H1U-TX is a 3x1 A/V auto switcher that features two HDMI inputs, one USB-C input,
one HDMI output, one HDBaseT output and one balanced analog audio output. The USB-C input
supports ALT-DP mode and can also charge a connected source device up to 40 was. The built in
HDBaseT transmier output can transmit HDMI or USB-C audio and video, RS232 and bi-direconal
IR over a single solid core shielded Category cable to a compable Intelix HDBaseT receiver up to 70
meters or 230 feet. The INT-AS2H1U-TX supports 1080p video signal up to 70m/230’ and 4K signals up
to 4K@60Hz / 4:2:0 / 8 bit color up to 40m/130’. The switcher supports CEC pass through and is HDCP
2.2 compliant. A built in web GUI allows easy conguraon of A/V roung, EDID, display automaon,
network and HDCP features. 48V PoH is built in to allow the INT-AS2H1U-TX HDBaseT transmier
output to power a compable Intelix receiver.
The switchers funcons can be controlled by built in web server / GUI, RS232 or by TCP/IP. The
INT-AS2H1U-TX can also manually control a connected display via CEC or RS232 or can be congured
to automate the display ON/OFF whenever a video signal is introduced or absent from the switcher
system.
The INT-AS2H1U-TX is compable with all Intelix HDBaseT receivers and any HDBaseT product that is
built to HDBaseT cered standards.
Product Overview
Package Contents
• INT-AS2H1U-TX 3x1 Auto Switcher
• Quick Install Guide
• (1) IR Receiver
• (1) IR Emier
• (1) RS232 to DB9 breakout cable
• (1) 5-pin phoenix connector
• (2) Mounng Clips with (4) Screws
• (4) Plasc Cushions
• 24V Power Adapter with US, EU, UK and AU plug adapters.

INT-AS2H1U-TX Quick Guide
4
Connecvity Instrucons
1. Verify all components included with the switcher / extender set are present before installaon.
2. Turn o power and disconnect the audio/video equipment by following the manufacturer’s
instrucons.
3. Connect Category 6 or greater twisted pair cable with RJ45 connectors between the INT-AS2H1U-
TX HDBaseT output / transmier to the HDBaseT input of a compable Intelix HDBaseT receiver. TIA/
EIA-568B straight-through wiring connecons must be used for this connecon.
4. Connect an HDMI cable that is less to or equal to 5 meters in length between the display and the
HDMI output of the HDBaseT receiver.
5. Connect an HDMI cable that is less to or equal to 5 meters in length between a local display and the
HDMI output of the INT-AS2H1U-TX local switcher.
6. Connect a source device to the HDMI inputs using a HDMI cable that is less than or equal to 5
meters in length
7. Connect a source device to the USB-C input using a USB-C video cable that is less than or equal to
2 meters in total length.
8. Connect RS232 control between the display to control connected display or connect to a 3rd party
control system to control switcher funcons (oponal)
NOTE: A list of control commands for this unit is available in the owners manual online at www.
libav.com under the DOCUMENTATION tab of the INT-AS2H1U-TX product page
9. Connect TCP/IP control to a 3rd party control system to control switcher funcons (oponal)
10. Connect IR receiver / emier to control components via HDBaseT receiver (oponal)
11. Set switch mode on front panel of INT-AS2H1U-TX for either manual or auto switching
12. Connect the included power supply to the INT-AS2H1U-TX and lock the power supply to the power
connector by twisng the locking collar clockwise.
13. Power on aached audio/video devices
Passing IR Signals:
The INT-AS2H1U-TX is capable of passing IR signals between 30 and 50 KHz. To prevent
damage to any of the electronics, the extender should be powered o while inserng
or removing any IR components. Inserng an IR transmier into the IR IN port may
damage the IR circuit for that extender.

INT-AS2H1U-TX Quick Guide
5
Cabling Wiring Requirements
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category 6
connecon between send and receive
units.
HDBaseT Cabling
To ensure proper performance of the INT-AS2H1U-TX, it is recommended that you use solid
core, shielded Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may perform
well but may not support power over HDBaseT reliably over longer distances.
For opmized HDBaseT performance use the following Liberty Wire and Cable branded
cabling;
Category 6 plenum; 24-4P-P-L6SH
Category 6A plenum; 24-4P-P-L6ASH
Category 6 NON-plenum; 24-4P-L6SH
Category 6A NON -plenum; 24-4P-L6ASH
When using shielded category cabling ALWAYS...
....use shielded connectors
....properly ground the category cable
RS232 Wiring
Connect a display or control system to the RS232 terminal
connector using low capacitance 2 conductor / shielded
cabled. Consult the manual of the control device(s) to
determine which pins the TX/RX signals are carried on. Be
sure to always connect TX to RX and RX to TX from the
connected device to the INT-AS2H1U-TX switcher system .
RS232 PORT
TX G RX
RX G TX
Connected RS232
Device Pins

INT-AS2H1U-TX Quick Guide
6
Technical Specicaons
Video
Video Inputs (2) HDMI, (1) USB-C
Video Input Connectors (2) HDMI Type A Female, (1) USB-C 3.0
Input video Signal HDMI for HDMI input, ALT-DP Mode for USB-C
HDMI Input Resoluon Support Up to 4Kx2K@60Hz 4:2:0 / 8 bit deep color
USB C Input Resoluon Support Up to 4Kx2K@30Hz 4:2:0 / 8 bit deep color
Video Output (1) HDMI, (1) HDBaseT (mirrored)
Video Output Connector (1) Type-A Female HDMI, (1) RJ45
Output Resoluon Support Up to 3840 x 2160 @60Hz / 4:2:0 / 8 bit deep color
Standards HDMI 2.0, HDCP 2.2 and CEC
System Bandwidth 10.2Gbps
Control
Control Ports (1) RS232, (1) IR IN, (1) IR OUT, (1) TCP/IP, (1) Firmware
Control Connectors (1) 3-pin terminal blocks, (2) 3.5mm jacks, (1) RJ45, (1) Micro USB
IR Carrier Frequency Range 33-55kHz at 5 volts
HDBaseT Signal Characteriscs
Maximum Distance 70 m (up to 1080p) , 40 m (up to 4K@60Hz / 4:2:0 / 8 bit deep color)
Cable Requirements Solid core shielded Category 6 F/UTP cable or greater with TIA/EIA-568B crimp paern
Chassis and Environmental
Dimensions (WxHxD) 269 mm x 30 mm x 100 mm (10.6 in x 1.2 in x 4 in)
Shipping Weight 465g (1 lbs.)
Operang Temperature 0° to +55° C (+32° to +131° F)
Operang Humidity 10% to 90%, Non-condensing
Storage Temperature -20° to +70° C (+14° to +158° F)
Storage Humidity 10% to 90%, Non-condensing
Power, ESD, and Regulatory
Power Supply Input 100V-240VAC / 50-60 Hz
Power Supply Output 24VDC / 4A
Power Consumpon 80 was (max)
ESD Protecon 15kV
Product Regulatory FCC, CE, RoHS
Power Supply Regulatory CE, RoHS
Other
Standard Warranty 5 years
Included Accessories Quick Install Guide, (1) 5-pin Phoenix connectors, (1) IR Emier, (1) IR Receiver, (1) RS232
to DB9 breakout cable, (1) DC24V 4A power adapter with US, EU, UK and AU power plug,
(2) Rack mount ears with 4 mounng screws, (4) Plasc Cushions
Compable Receivers INT-HD70-RX, INT-HDX100-RX (up to 70m), INT-HDX100-RXWP (up to 70m) and INT-
BSR4K-H2 (receiver must be powered locally).
Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and electrical interference, and cable
patches.

Thank you for your purchase.
For Technical Support please call our toll free number at
800-530-8998 or email us at [e-mail]
www.libav.com
Intelix is a brand of:
11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: [phone]
Fax: [phone]
Toll-Free: 800-530-8998