Intelligent network solutions DNX-A-2R-K User manual

Man-1529 Rev.01
INS Quick Start Guide
Intelligent Network Solutions
DNX-A-2R-K & DNX-R-2F/FC-K
Quick Start Guide
*Man-1529*

Safety
Suppliers of articles for use at work are required under section 6 of the Health and Safety at Work Act 1974 to ensure
as reasonably as is practical that the article will be safe and without risk to health when properly used.
An article is not regarded as properly used if it is used ‘without regard to any relevant information or advice’ relating
to its use made available by the supplier.
This product should be iNStalled, commissioned and maintained by trained service personnel in accordance with
the following:
(i) Regulations for electrical equipment in buildings specific to the country of use.
(ii) Codes of practice
(iii) Statutory requirements
(iv) Any iNStructions advised by the manufacturer.
According to the provisions of the Act you are therefore requested to take such steps as are necessary to ensure
that you make any appropriate information about this product available to anyone concerned with its use.
Suppliers of articles for use at work are required under section 6 of the Health and Safety at Work Act 1974 to ensure
as reasonably as is practical that the article will be safe and without risk to health when properly used.
An article is not regarded as properly used if it is used ‘without regard to any relevant information or advice’ relating
to its use made available by the supplier.
This product should be iNStalled, commissioned and maintained by trained service personnel in accordance with
the following:
(i) IEE regulations for electrical equipment in buildings
(ii) Codes of practice
(iii) Statutory requirements
(iv) Any iNStructions specifically advised by the manufacturer
According to the provisions of the Act you are therefore requested to take such steps as are necessary to ensure
that you make any appropriate information about this product available to anyone concerned with its use.
This equipment is designed to operate from 115V AC to 230V AC 50/60Hz maiNS supplies and is of class 1 con-
struction. As such it must be connected to a protective earthing conductor in the fixed wiring of the iNStallation and
a readily accessible double pole disconnect device meeting the requirements of EN60950/IEC950 which discon-
nects live and neutral simultaneously shall be incorporated in the fixed wiring.
Switch disconnect devices such as MK Sentry 63A or similar are suitable for this. Failure to ensure that all conduc-
tive accessible parts of this equipment are adequately bonded to the protective earth will render the equipment un-
safe.
This Control Panel is environmental class A and is designed for indoor use only at temperatures between -10°C and
+45°C with a maximum relative humidity of 95%. The IP rating for the enclosure is IP30.
Operation outside of these limits may render the equipment unsafe.

Man-1529 Rev.01
iNS Quick Start Guide
1
iNS Quick Start Guide
This Start Guide provides iNS module connection/settings overview and links to the product range User Guides.
QR Codes
The QR codes below provide links to iNS User Manuals. Using your Smartphone, tablet or device (where necessary)
install a third party QR Code Reader and scan the code to open the documents.
Figure A-1
Reading the QR Codes
Should you be unable to work with QR codes Manuals can be obtained by visiting the following website pages:
Important! Information in this Start Guide is supplementary.
The product Installation Manual and Operation Manual should read, understood and referred to throughout.
DNX-A-2R-K
User Guide
DNX-R-2F/FC-K
User Guide
Manual Variant Website
DNX-A-2R-K User Guide http://www.kentec.co.uk/manuals/man-1491.pdf
DNX-R-2F/FC-K User Guide http://www.kentec.co.uk/manuals/man-1492.pdf

Man-1529 Rev.01
iNS Quick Start Guide
2
Figure A-2
DNX-A-2R-K Dual Port Fire Alarm Control Panel Connections & Selection Settings

Man-1529 Rev.01
iNS Quick Start Guide
3
Figure A-3
DNX-R-2F/FC-K Dual Port Fire Alarm Control Panel Fibre Connections & Passive Mode Settings

Man-1529 Rev.01
iNS Quick Start Guide
4
Figure A-4
DNX-R-2F/FC-K Dual Port Fire Alarm Control Panel Fibre/RS485 Connections & Selection Settings

Man-1529 Rev.01
iNS Quick Start Guide
5
Terms and Conditions
Details of Kentec Electronics Ltd. Terms and Conditions including Warranties and Returns & Repair Policies can be
found on our website at the following locations:
Address of Kentec Electronics Ltd.
Units 25-26 Fawkes Avenue,
Questor, Dartford,
Kent. DA1 1JQ
United Kingdom
Registered in England:FACP
No.1937570
Tel: [phone]
http://www.kentec.co.uk
Disclaimer
In no event shall The Manufacturer be liable for any damages or injury of any nature or kind, no matter how caused, that arise from
the use of the equipment referred to in this manual. Strict compliance with the safety procedures set out and referred to in this
manual, and extreme care in the handling or use of the equipment, are essential to avoid or minimise the chance of personal injury
or damage to the equipment. The information, figures, illustrations, tables, specifications, and schematics contained in this manual
are believed to be correct and accurate as at the date of publication or revision. However, no representation or warranty with re-
spect to such correctness or accuracy is given or implied and The Manufacturer will not, under any circumstances, be liable to any
person or corporation for any loss or damages incurred in connection with the use of this manual.
The information, figures, illustrations, tables, specifications, and schematics contained in this manual are subject to change without
notice. Unauthorised modifications to the fire detection system or its installation are not permitted, as these may give rise to unac-
ceptable health and safety hazards. By installing this equipment on a computer network, the owner accepts full and unequivocal
responsibility for ensuring that it is protected against all cyber threats and illegal tampering during the lifetime of the equipment.
Any software forming part of this equipment should be used only for the purposes for which The Company supplied it. The user
shall undertake no changes, modifications, conversions, translations into another computer language, or copies (except for a nec-
essary backup copy). In no event shall The Manufacturer be liable for any equipment malfunction or damages whatsoever, includ-
ing (without limitation) incidental, direct, indirect, special, and consequential damages, damages for loss of business profits,
business interruption, loss of business information, or other pecuniary loss, resulting from any violation of the above prohibitions.
Terms, Conditions & Warranty https://kentec.co.uk/terms-and-conditions/
Returns & Repairs http://www.kentec.co.uk/returns-and-repairs/