Cisco Small Business SF200-24P User manual

Quick Start Guide
Cisco Small Business
200 Series Smart Switches

2 200 Series Smart Switches
Welcome
Thank you for choosing the Cisco 200 Series Smart Switch, a Cisco Small
Business network communications device. This device is designed to be
operational right out-of-the-box as a standard bridge. In the default
configuration, it will forward packets between connecting devices after
powered up.
Package Contents
•Cisco SF 200-24, SF 200-24P, SF 200-48, SF 200-48P, SG 200-18, SG
200-26, SG 200-26P, SG 200-50, or SG 200-50P Smart Switch.
•Rackmount Kit.
•Power Cord.
•This Quick Start Guide.
•Product CD.
This guide will familiarize you with the layout of the smart switch and
describe how to deploy the device in your network. For additional
information, see www.cisco.com/smb.
Mounting the Cisco Switch
There are two ways to mount the switch:
• Set the switch on a flat surface.
• Mount the switch in a standard rack (1 rack unit high).
Do not mount the device in a location where any of the following conditions
exist:
High Ambient Temperature—The ambient temperature must not
exceed 104 degrees Fahrenheit (40 degrees Centigrade).
Reduced Air Flow—Both side panels must be unobstructed to prevent
overheating.
Mechanical Overloading—The device must be level, stable, and
secure to prevent it from sliding or shifting out-of-position.
Circuit Overloading—Adding the device to the power outlet must not
overload that circuit.
1

200 Series Smart Switches 3
Rack-Mount Placement
If your switch is rack-mount capable, it will come with a rack-mount kit. To
rack-mount the switch in any standard rack, attach the brackets to the
sides of the switch with the supplied hardware and secure the brackets.
CAUTION For stability, load the rack from the bottom to the top, with the
heaviest devices on the bottom. A top-heavy rack is likely to
be unstable and might tip over.
Connecting Network Devices
To connect the smart switch to the network:
STEP 1Connect the Ethernet cable to the Ethernet port of a computer,
printer, network storage, or other network device.
STEP 2Connect the other end of the Ethernet cable to one of the
numbered smart switch Ethernet ports.
The LED of the port lights if the device connected is active. Refer to
Features of the Cisco Small Business Smart Switch, page 7 for
details about the different ports and LEDs on each switch.
STEP 3Repeat Step 1 and Step 2 for each device you want to connect to
the smart switch.
NOTE Cisco recommends using Cat5 or better cable for Gigabit
connectivity. When you connect your network devices, do not exceed
the maximum cabling distance of 328 feet (100 meters). It can take up to
one minute for attached devices or the LAN to be operational after they
are connected. This is normal behavior.
Power over Ethernet Considerations
If your switch is one of the Power over Ethernet (PoE) models, consider the
following power requirement:
•As a Power Sourcing Equipment (PSE) device, the switch can deliver a
maximum of 15.4 Watts per PoE port to a Powered Device (PD).
2

4 200 Series Smart Switches
PoE is available on the following ports:
Use the following table to determine the total power budget available for
all devices on your switch.
Configuring the Cisco Small Business
Smart Switch
Before You Begin
Verify that a computer with Microsoft Internet Explorer (version 6 or higher)
or Firefox (version 2.0 or higher) is available.
Accessing and Managing Your Switch Using the Web-
Based Interface
In order to access the switch with a web-based interface, you must know
the management IP address of the switch. The default configuration of the
switch is to use its factory default IP address of 192.168.1.254 until it has
obtained an IP address from a DHCP server, or it has been changed to a
static IP address.
When the switch is using the factory default IP address, its System LED
flashes continuously. When the switch is using a DHCP assigned IP
address or an administrator configured static IP address, the System LED
lights steady.
NOTE If the smart switch IP address is changed, either by a DHCP server
or manually, your access to the smart switch will be lost and you must
use the new IP address to configure the device.
To configure the smart switch:
STEP 1Power on the computer and the switch.
STEP 2Connect the computer to the switch. You can connect to the same
IP subnet as the switch by connecting them directly with an
Model Ports
SF 200-24P and SG 200-26P 1—6 and 13—18
SF 200-48P and SG 200-50P 1—12 and 25—36
Model Power Dedicated to PoE
SF 200-24P 100 Watts
SF 200-48P 180 Watts
SG 200-26P 100 Watts
SG 200-50P 180 Watts
3

200 Series Smart Switches 5
Ethernet cable, or by connecting to the same LAN where the
switch is located through other switches. You can also connect
your computer to the switch from another IP subnet through one or
more IP routers.
STEP 3Set up the IP configuration on your computer.
a. If the switch is using the default static IP address of
192.168.1.254, you must choose an IP address in the range of
192.168.1.1—192.168.1.253 that is not already being used by
another device.
b. If the IP addresses will be assigned by DHCP, make sure your
DHCP server is running and can be reached from the switch
and the computer. You might need to disconnect and
reconnect the devices for them to discover their new IP
addresses from the DHCP server.
NOTE Details on how to change the IP address on your computer
depend upon the type of architecture and operating system you are
using. See your computer’s local Help and Support functionality
and search for “IP Addressing.”
STEP 4Open a Web browser window. If you are prompted to install an
Active-X plug-in when connecting to the device, follow the
prompts to accept the plug-in.
STEP 5Enter the switch IP address in the address bar and press Enter. For
example, http://192.168.1.254.
The Smart Switch Login page
displays.
STEP 6Enter the login information:
Username is cisco
Default password is cisco (passwords are case sensitive)
STEP 7If this is the first time that you have logged on with the default
username and password, the
Change Password page opens. Enter
a new administrator password and then click Apply.
CAUTION Make sure that any configuration changes that you made are
saved before exiting from the web-based interface by
clicking on the Save icon, then clicking Apply. Exiting before
you save your configuration will result in all changes being
lost.
The Getting Started window displays. You are now ready to configure the
switch. Refer to the
Cisco Small Business Smart Switch Administration
Guide
for further information.

6 200 Series Smart Switches
Troubleshoot Your Connection
If you cannot access your switch from the web-based interface, the switch
might not be reachable from your computer. You can test network
connections by using the ping command. The following section shows
how to use “ping” in a Windows environment:
STEP 1Open a command window by using Start > Run and enter cmd.
STEP 2At the Command window prompt enter ping and the smart switch
IP address. For example ping 192.168.1.254 (the default IP address
of the smart switch).
If you can reach the switch, you should get a reply similar to the
following:
Pinging 192.168.1.254 with 32 bytes of data:
Reply from 192.168.1.254: bytes=32 time<1ms TTL=128
If you cannot reach the switch, you should get a reply similar to the
following:
Pinging 192.168.1.254 with 32 bytes of data:
Request timed out.
Possible Causes and Resolutions
No Power:
Power up the switch and your computer if they are turned off.
Bad Ethernet connection:
Check the LEDs for proper indications. Check the connectors of the
Ethernet cable to ensure they are firmly plugged into the switch and
your computer.
Wrong or conflicting IP address:
Make sure that you are using the correct IP address of the switch. You
can verify the current IP address of the switch with your network
administrator. The System LED provides an indication of where the
switch received the IP address, see Section 4 for details.
Make sure that no other device is using the same IP address as the
switch.
No IP route:
If the switch and your computer are in different IP subnets, you need
one or more routers to route the packets between the two subnets.

200 Series Smart Switches 7
Unusually long access time:
Due to the spanning tree loop detection logic, adding new connections
might take 30 to 60 seconds for the affected interfaces and/or LAN to
become operational.
Features of the Cisco Small Business
Smart Switch
This section describes the exterior of the smart switches including ports,
LEDs, and connections. Not all models will have all of the features
described.
Ports
RJ-45 Ethernet Ports—Use these ports to connect network devices, such
as computers, printers, and access points, to the switch.
MiniGBIC (if present)—The miniGBIC (gigabit interface converter) ports are
connection points for miniGBIC modules, so the smart switch can uplink to
other switches by using optical fiber.
•MiniGBIC ports are compatible with Cisco miniGBIC modules MGBSX1,
MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1, and MFEBX1, as well as
other brands of miniGBIC modules.
• MiniGBIC interface is a combination port, shared with one other RJ-45
interface. When the MiniGBIC is active, the adjacent RJ-45 port is
disabled.
•The LEDs of the corresponding RJ-45 port flashes green to respond to
the miniGBIC interface traffic.
4

8 200 Series Smart Switches
LEDs
System LED—(Green) Lights steady when the switch is powered on, and
flashes when booting, performing self tests, and acquiring an IP address. If
the LED flashes amber, the switch has detected a hardware failure.
LINK/ACT LED—(Green) Located on the left of the port. Lights steady
when a link between the corresponding port and another device is
detected. Flashes when the port is passing traffic.
NOTE The System and LINK/ACT LEDs are on each model of the switch.
The following LEDs are only present on switch models that have those
capabilities:
PoE (if present)—(Amber) Located on the right of the port. Lights steady to
indicate that power is being supplied to a device attached to the
corresponding port.
100M LED (if present)—(Green) Located on the right of the port. Lights
steady when another device is connected to the port, is powered on, and a
100 Mbps link is established between the devices. When the LED is off, the
connection speed is under 100 Mbps or nothing is cabled to the port.
Gigabit LED (if present)—(Green) Located on the right of the port. Lights
steady when another device is connected to the port, is powered on, and a
1000 Mbps link is established between the devices. When the LED is off,
the connection speed is under 1000 Mbps or nothing is cabled to the port.
MiniGBIC (if present)—(Green) Located on the right of the port. Lights
steady when a connection is made through the shared RJ-45 port. Flashes
when the port is passing traffic.
Additional Features
The switch might also have a reset button. The switch can be reset by
inserting a pin or paper clip into the reset opening. See “Returning the
Device to the Factory Default Settings” for details.

200 Series Smart Switches 9
Back Panel
The power port is located on the back panel of the smart switch.
Returning the Device to the Factory
Default Settings
To use the Reset button to reboot or reset the smart switch, do the
following:
•Toreboot the smart switch, press the Reset button for less than 10
seconds.
•To restore the smart switch configuration to the factory default settings:
1. Disconnect the smart switch from the network or disable all DHCP
servers on your network.
2. With the power on, press and hold the Reset button for more than
10 seconds.
5

10 200 Series Smart Switches
Where to Go From Here
Support
Cisco Small Business Support
Community
www.cisco.com/go/smallbizsupport
Cisco Small Business Support
and Resources
www.cisco.com/go/smallbizhelp
Phone Support Contacts www.cisco.com/en/US/support/tsd_cisco_
small_business_support_center_contacts.html
Cisco Small Business Firmware
Downloads
www.cisco.com/go/smallbizfirmware
Select a link to download firmware for Cisco
Small Business Products. No login is required.
Downloads for all other Cisco Small Business
products, including Network Storage Systems,
are available in the Download area on
Cisco.com at www.cisco.com/go/software
(registration/login required).
Product Documentation
Cisco Small Business Smart
Switches
www.cisco.com/go/smallbizsmartswitches
200 Series Smart Switches
Quick Start Guide
www.cisco.com/en/US/docs/switches/lan/
csbss/sf20x_sg20x/quick_start/78-19501-
01.pdf
200 Series Smart Switches
Administration Guide
www.cisco.com/en/US/docs/switches/lan/
csbss/sf20x_sg20x/administration_guide/OL-
22849-01.pdf
Regulatory, Compliance, and
Safety Information
www.cisco.com/en/US/docs/switches/lan/
csbms/sfe2000/release/notes/
Class_A_Switches_RCSI.pdf
Warranty Information www.cisco.com/go/warranty
Cisco Small Business
Cisco Partner Central for Small
Business (Partner Login
Required)
www.cisco.com/web/partners/sell/smb
Cisco Small Business Home www.cisco.com/smb
6