Inter-fab Adrenaline Slide User manual

ADR1-IM R v. 4/16 (ADR-INSTALL)
ADRENALINE™SLIDE
Assembly & Installation Instru tions
RIGHT
TURN
SLIDE
LEFT
TURN
SLIDE
IMPORTANT!
THESE INSTRUCTIONS
MUST REMAIN WITH
THE SLIDE OWNER!
Visit inter-fab.co /safety to view important
slide safety messages with your kids!
INTER-FAB, INC. 3050 S. ALVERNON WAY • TUCSON, AZ 85713
520.790.7040 • 800.737.5386 • FAX [phone] • inter-fab. om
WARNING: IMPORTANT INSTALLATION INFORMATION
Th installation of this product should b don only by a lic ns d and prof ssional install r. Installation should
b don strictly in conformanc with all local building cod s, l ctrical cod s and oth r building and saf ty laws
and r gulations. Among oth r things, that your install r should car fully analyz th n d to bond th product
to pr v nt an l ctrical hazard. Failur to prop rly install this product could r sult in a dang rous condition,
including but not limit d to l ctrical or structural hazards. Int r-Fab, Inc. disclaims all liability arising from th
installation and th us r assum s all risk associat d with th installation.

INSTALLATION MANUAL ADRENALINE™ SLIDE
1
ADR1-IM R v. 4/16 (ADR-INSTALL)
TABLE OF CONTENTS:
Important Notic s to th Install r..............................................2
Int nd d Us Instructions ........................................................3
Wat r Saf ty Env lop .............................................................4
Slid Plac m nt & Footprint Diagrams - L ft Turn .......................5
Slid Plac m nt & Footprint Diagrams - Right Turn......................6
Slid Compon nts ...................................................................7
St p 1: Attach Ladd r Entry S ction .........................................8
St p 2: Attach Handrails to Ladd r & Entry S ction ...............9-11
St p 3: Attach Foot P d stals to L gs ....................................11
St p 4: Attach L gs to Flum .................................................12
St p 5: Ass mbl th Flum S ctions.................................12-13
St p 6: Attach Entry S ction & Ladd r to Flum .......................13
St p 7: Position Slid Ass mbly on D ck..................................14
St p 8: Anchor Slid to D ck.............................................15-16
St p 9: Align Flum S ctions..................................................16
St p 10: Tight n L g R c iv r Through Bolts ...........................17
St p 11: Conn ct Wat r Supply Syst m ..................................17
St p 12: Finishing St ps........................................................17
Final Insp ction Ch ck List .....................................................17
Slid Car & Maint nanc ......................................................18
Pav r Kit Information........................................................18-20
Explod d Vi w of Adr nalin Slid ............................................21
Parts List (corr sponds with xplod d vi w)..............................22
Hardwar Kit Information.......................................................23
Not s..................................................................................24
Int r-Fab Limit d Warranty.....................................................25

INSTALLATION MANUAL ADRENALINE™ SLIDE
2
ADR1-IM R v. 4/16 (ADR-INSTALL)
INTER-FAB HIGHLY RECOMMENDS THAT YOU READ THE ENTIRE INSTALLATION
MANUAL BEFORE YOU ATTEMPT THE INSTALLATION OF THE ADRENALINE SLIDE.
YOU MUST USE THE PROVIDED ANTI-SEIZE ON ALL THE BOLTS AND ALL-THREADS
OR THE NUTS WILL SEIZE.
INTER-FAB RECOMMENDS THAT A THREE-PERSON CREW ASSEMBLE THE
ADRENALINE SLIDE.
INTER-FAB HIGHLY RECOMMENDS THAT YOU FOLLOW THE INSTALLATION
SEQUENCE IN THIS MANUAL.
THE SLIDE POSITIONING GRAPHICS ON PAGES 5 AND 6 ARE FOR REFERENCE
ONLY. INTER-FAB STRONGLY RECOMMENDS THAT ONLY THE FULLY AND
CORRECTLY ASSEMBLED SLIDE BE USED TO LOCATE THE POSITIONS FOR THE
ANCHOR BOLTS AS DESCRIBED ON PAGE 15.
THE LOWER AND UPPER FLUME SECTIONS ARE EACH SUPPLIED WITH A METAL
FISH WIRE TO PULL THE 3/8” VINYL TUBING FROM THE EXIT SECTION UP TO
THE WATER OUTLET PLUMBING IN THE ENTRY SECTION. BE CAREFUL NOT TO
REMOVE THE FISH WIRE FROM BOTH FLUME SECTIONS DURING UNBOXING
AND HANDLING.
INTER-FAB RECOMMENDS THAT THE ADRENALINE SLIDE BE INSTALLED ON A
CONCRETE DECK WITH A MINIMUM THICKNESS OF 4”.
IMPORTANT NOTICES TO THE INSTALLER

INSTALLATION MANUAL ADRENALINE™ SLIDE
3
ADR1-IM R v. 4/16 (ADR-INSTALL)
INTENDED USE INSTRUCTIONS
1. Ev ryon who us s this slid must know, und rstand and follow th s instructions
2. Th ANSI/APSP/ICC-5 2011 standard for abov ground pools prohibits th us of slid s or diving boards
on abov ground pools or on ground pools.
3. This slide is designed for residential inground pool use ONLY. This slide may not be used on any
above ground or on ground pool. Su h use of this slide may result in serious injury or death.
4. This slid should n v r b install d on abov ground pools, ponds, floating docks or platforms, boat docks
or hous boats or any natural body of wat r.
5. This slid should n v r b install d on any comm rcial, public or s mi-public pool.
6. B familiar with th shap and d pth of th pool b for you slid . This slid should only b us d with th
prop r wat r saf ty nv lop , as d scrib d in Diagrams A, B & C on pag 4 and in accordanc with th
slid positioning Diagrams D, E, F and G on pag s 5 and 6.
7. B caus th slid may only b us d in wat r 4’6” d p or gr at r, all slid us rs must b abl to swim
in d p wat r.
8. W ight limit for this slid is 300 pounds, no slid r w ighing mor than 300 pounds may us this slid .
9. Th surfac of th slid is v ry slipp ry wh n w t; USE CAUTION wh n nt ring th slid and wh n
transitioning from standing to sitting.
10. Slid in a f t first sitting position ONLY.
11. IMPORTANT: sliding h adfirst is prohibit d: s rious spinal injury r sulting in paralysis or d ath can r sult.
12. Maintain adult sup rvision at all tim s.
13. Only on p rson at a tim is allow d on th slid ; this includ s th ladd r.
14. B sur th wat r d liv ry syst m is on and lubricating th slid prior to us .
15. Collision with anoth r swimm r or a div r can r sult in s rious injury or d ath for on or both p rsons:
B for sliding, always mak sur that th path in front of th slid is fr from any (including subm rg d)
obstructions including oth r p opl or obj cts in th pool such as rafts, inn r tub s tc. Wh n a diving
board is also pr s nt, mak sur you do not us th slid whil som on is on or using a diving board.
Tak turns.
16. No roughhousing or hors play should b allow d on th slid at any tim .
17. Do not stand, jump or div from any part of th slid .
18. Do not slid on obj cts such as rafts or inn r tub s. doing so gr atly incr as s your risk of injury.
19. Do not slid through or at obj cts such as rafts or inn r tub s, doing so gr atly incr as s your risk of
injury.
20. Do not us this slid if physically impair d or handicapp d without your doctor’s p rmission.
21. Do not us this slid with a history of h art conditions, s izur s, back probl ms, fainting or f ar of
h ights.
22. Do not us this slid if you ar pr gnant.
23. Do not drink alcohol and us this slid .
24. Don’t tak chanc s, insp ct th slid at l ast onc a y ar (s th slid insp ction list on pag 17, do
not us th slid if any part b com s loos , damag d, w ak n d or brok n. If n c ssary, b for using
th slid again, hav it insp ct d and r pair d by a comp t nt prof ssional familiar with pool slid s.
25. Giv n that th Adr nalin is us d in a swimming pool nvironm nt a c rtain amount of wat r and moistur
should b xp ct d to accumulat on th pool d ck within th vicinity of th slid . This r sults not only
from splashing from rid rs nt ring into th pool but also splashing from wat r runoff as it xits th slid .
To minimiz this, th rat of wat r flow to th slid can b r duc d whil in us and th slid wat r
sourc should b turn d off wh n th slid is not in us .
SLIDE IN A SITTING
POSITION ONLY
Fac forward on th slid , holding th l gs and arms
with th palms of your hands forward and tilt d up.
WARNING: SERIOUS INJURY OR DEATH CAN RESULT FROM THE
IMPROPER INSTALLATION OR USE OF THIS SLIDE.
When installed a ording to these instru tions, this slide onforms to
Consumer Produ t Safety Standard Guidelines.
DO NOT SLIDE HEAD FIRST SERIOUS INJURY
CAN RESULT DEEP WATER SWIMMERS
ONLY

INSTALLATION MANUAL ADRENALINE™ SLIDE
4
ADR1-IM Rev. 4/16 (ADR-INSTALL)
DIAGRAM A
(NOT TO SCALE)
DIAGRAM C
(NOT TO SCALE)
Minimum Water Safety Envelope
WATER SAFETY ENVELOPE:
A minimum water depth of three feet (3') under the exit
of the slide which increases to a depth of four feet (4'6")
at point A which is located four feet six inches (4'6")
from the back wall of the pool. A minimum depth of
four feet (4'6") must be maintained at a distance of
nine feet (9') along the centerline of the slide from point
A. The above described water depth profile shall
extend a minimum of three feet three inches (3'3") on
either side of the centerline of the slide.
(See Diagrams A, B & C)
DIAGRAM B
(NOT TO SCALE)
Minimum Slide Clearance Area
ALL SLIDES SHOULD
BE GROUNDED
Check your local electrical
code requirements.
ADRENALINE

INSTALLATION MANUAL ADRENALINE™ SLIDE
5
ADR1-IM R v. 4/16 (ADR-INSTALL)
SLIDE PLACEMENT DIAGRAM & FOOTPRINT DIAGRAM
Adrenaline Slide - Left Turn
DIAGRAM D
(NOT TO SCALE)
DIAGRAM E
(NOT TO SCALE)

INSTALLATION MANUAL ADRENALINE™ SLIDE
6
ADR1-IM Rev. 4/16 (ADR-INSTALL)
SLIDE PLACEMENT DIAGRAM & FOOTPRINT DIAGRAM
Adrenaline Slide - Right Turn
DIAGRAM F
(NOT TO SCALE)
DIAGRAM G
(NOT TO SCALE)

INSTALLATION MANUAL ADRENALINE™ SLIDE
7
ADR1-IM R v. 4/16 (ADR-INSTALL)
Handrail (2)
1–Right; 1–Left Long Leg Short Leg
Step Assembly Foot Pedestal (2)
ADRENALINE SLIDE COMPONENTS
Left Turn Slide Flume Parts
Right Turn Slide Flume Parts

INSTALLATION MANUAL ADRENALINE™ SLIDE
8
ADR1-IM R v. 4/16 (ADR-INSTALL)
LIST OF REQUIRED TOOLS
Tools required for assembly and installation of Adrenaline slide:
NOTE: USE PROVIDED ANTI-SEIZE ON ALL BOLTS!
NOTE: Use slide box and pa kaging during assembly to prote t slide omponents
from damage from the de king surfa e.
STEP ONE: Attach the Ladder to the Entry Section
Thr ad th fl x PVC hos from th ntry s ction through th st p tub ass mbly and out th
pr -drill d hol abov th bottom st p. Utilizing hardwar kit ADR-103-SS and anti-s iz ,
attach th ladd r to th ntry s ction on th ground. B car ful not to scratch th slid ; us th
cardboard box th slid arriv d in for prot ction. Ins rt th top of th ladd r into th ladd r
r c iv r on th ntry s ction and align th hol s. (See Fig 2 & 3) Plac a 3/8” flat wash r ov r
a 3/8”x9-1/2” bolt with anti-s iz , th n push bolt compl t ly through th pr -drill d hol s in th
ntry s ction l g r c iv r and th PVC ladd r; th n plac a 3/8” flat wash r th n a 3/8” lock
wash r th n a nut on th bolt; hand tight n only. (Th s will b tight n d aft r attachm nt
to flum / xit s ction.
NOTE: Install bolts from step side – nuts will be under entry section
Fig. 2 Fig. 3Fig. 1
1. Hammer
2. 3/8" drive rat het
3. 3/8" x 6" rat het extension
4. 1/2" deep so ket (deep
so ket is ne essary)
5. 9/16" so ket
6. 9/16" box end rat het
wren h
7. Drill with 3/8" masonry bit
8. Tape measure
9. PVC Pipe Cutter
10. Level
11. Angle Finder
12. Pliers
13. Razor Knife
IMPORTANT NOTE: Th Adr nalin pool slid us s a propri tary wat r supply and drain
syst m. Wat r is suppli d at th top of th slid as w ll as to th drain unit in th xit. Th
xit drain also s rv s to r mov any standing wat r wh n th slid is not in us . Th plumbing
is factory install d but th drain in th xit s ction must b conn ct d to th ntry wat r
outl t plumbing during slid installation. Th xit s ction is plumb d with a l ngth of 3/8”
cl ar vinyl tubing and a r d cap as shown in Figur 1. Th r d cap will facilitat pulling th vinyl
tubing through th low r and upp r flum s ctions. Th r d cap will b cut off and discard d
wh n th slid plumbing is conn ct d.
RED CAP

9
ADR1-IM R v. 4/16 (ADR-INSTALL)
INSTALLATION MANUAL ADRENALINE™ SLIDE
Fig. 5
STEP TWO: Attach the Handrails to the Ladder and Entry Section
TIP: Install th handrails as shown in Figure 4 b low.
TIP: Hand tight n th all-thr ads into th handrails only, do not us any m chanical m ans
such as a wr nch or pli rs to tight n th all-thr ads.
TIP: Th r ar 8 all-thr ads utiliz d on ach handrail. Th r ar 3 diff r nt l ngths of all-
thr ads us d on ach handrail. See Fig 5 below to match actual size (ADR-105-SS Kit)
TIP: Th offs t at th bottom of ach handrail fac s in as th st p attachm nt point is
narrow r than th ntry s ction.
Fig. 4: Ba k View of Ladder Se tion Assembly

INSTALLATION MANUAL ADRENALINE™ SLIDE
10
ADR1-IM R v. 4/16 (ADR-INSTALL)
STEP TWO: Attach the Handrails to the Ladder and Entry Section - CONT.
Ins rt th corr ct l ngth of all-thr ad into th nuts mb dd d in th handrails th n attach
th handrails as illustrat d. (See Fig 6 and 7)
Hand tight n all-thr ad into ach of th 8
locations on th handrails. Ensur corr ct
l ngth of all-thr ad is us d at ach location.
(See Fig 5 on page 9 )
5/16” x 2-1/2” all-thr ad (3 ach as shown)
5/16” x 4” all-thr ad (3 ach as shown)
5/16” x 5” all-thr ad (2 ach as shown)
Mak sur to us provid d anti-s iz on th
all-thr ad b for ins rting into th mb dd d
nuts.
Ins rt handrail into th top s ction first as
illustrat d. Push or pull th handrail apart
until th all-thr ads pass through th 5
hol s in th ntry s ction and through th
hol s drill d in th upp r 3 st ps.
5/16”x2-1/2”
Fig. 6
Fig. 7
5/16”x4”
5/16”x5”
Th s 5 locations on th ntry s ction that
r c iv a flang nut only. (See Fig 8) Mak sur
to us th provid d anti-s iz on th all-thr ads
b for attaching th flang nuts. A flat wash r
is not n d d. Hand tight n.
Fig. 8

INSTALLATION MANUAL ADRENALINE™ SLIDE
11
ADR1-IM R v. 4/16 (ADR-INSTALL)
Th s thr locations r quir a flat wash r,
flang nut and rubb r cap. (See Fig 9) Mak
sur to us th provid d anti-s iz on th all-
thr ads b for attaching th flang nuts. Hand
tight n.
NOTE: 1/8” – 1/4” of the all-threads will
extend through the flange nut.
Fig. 9
STEP TWO: Attach the Handrails to the Ladder and Entry Section - CONT.
STEP THREE: Attach the Foot Pedestals to the Legs
TIP: Both PVC l gs hav a diff r nt hol drill patt rn at ach nd. Th r is a top/bottom
ori ntation. Th offs t bolt hol s go to th top and bolt to th flum s. (See Fig 11)
Ins rt th corr ct nd of th long PVC l g into th foot p d stal, align th hol s, utilizing
hardwar kit ADR-101-SS and anti-s iz , plac a flat wash r ov r a 3/8” bolt; th n push
bolt through th pr -drill d hol s in th PVC l g and th foot p d stal, th n plac flat wash r
th n 3/8” nylon nut and fully tighten now. R p at th proc ss for th short PVC l g.
NOTE: Do not remove fish wire. (See Fig 10)
Fig. 11Fig. 10

INSTALLATION MANUAL ADRENALINE™ SLIDE
12
ADR1-IM R v. 4/16 (ADR-INSTALL)
STEP FOUR: Attach the Legs to the Flu e
Ins rt th top of th long l g into l g r c iv r of th upp r flum , and th top of th short l g
into th l g r c iv r of th low r flum . Align hol s, th n utilizing hardwar kit ADR-103-SS
and anti-s iz , plac a 3/8” flat wash r ov r a 3/8”x9-1/2” bolt, th n push bolt compl t ly
through th pr -drill d hol s in th l g r c iv r and PVC l g th n plac a 3/8” flat wash r
th n a lock wash r and a nut. Hand tight n only at this tim , th s will b tight n d aft r
th flum is align d. (See Fig 12 & Fig 13)
NOTE: Install th 3/8” x 9-1/2” bolts through th hol s from th high r sid of th flum ,
pushing th m through toward th xit of th slid .
Fig. 12 Fig. 13
STEP FIVE: Asse ble the Flu e Sections
TIP: Hand tight n th flum bolts for now (b sur to apply anti-s iz on bolts), th y will b fully
tight n d onc th flum is corr ctly align d.
TIP: Th r ar 3 factory install d gask ts. Ensur that a gask t is in plac on th ntry s ction,
th upp r flum and th low r flum .
Start th flum ass mbly by placing th xit s ction upright on its front p d stal as clos
as possibl to its final position on th pool d ck. N xt, turn th low r flum upright on its
p d stal.
With xit s ction in its approximat final position, plac th low r flum with l g and p d stal
about 12” from th xit. Us th hook in th nd of th fish wir to conn ct to th hol in
th nd of th r d cap on vinyl tubing. B nd th nd of th wir to clos th hook as shown
in Figure 14. G ntly pull th vinyl tubing through th flum s ction with th fish wir . Pull all
tubing through and b car ful not to kink th tubing or g t it caught b tw n conn ction
flang s as th parts ar bolt d tog th r.
Fig. 14
RED CAP

INSTALLATION MANUAL ADRENALINE™ SLIDE
13
ADR1-IM R v. 4/16 (ADR-INSTALL)
Fig. 15
STEP FIVE: Asse ble the Flu e Sections - CONT.
Using hardwar kit ADR-102-SS and anti-s iz , align th 5 flang hol s, plac flat wash r
ov r 3/8” bolt, th n push compl t ly through th flang . Plac a flat wash r, lock wash r
and nut onto th bolt and just hand tight n at this tim .
N xt, turn th upp r flum upright on its l g and p d stal, r p at th abov flang -to-flang
bolting proc ss. (See Fig 15)
Position th upp r flum with l g and p d stal about 12’ from th low r flum . Car fully
r mov th low r flum fish wir from th r d cap and attach th upp r flum fish wir .
B nd th nd of th wir shut as in Figure 14 on pag 12.
G ntly pull th vinyl tubing through th flum s ction with th fish wir . Pull all tubing through
and b car ful not to kink th tubing or g t it caught b tw n conn ction flang s as th
parts ar bolt d tog th r. L av th fish wir attach d to th cap and tubing. This will insur
that th tubing is not pull d back into th flum s ction during positioning of th slid .
STEP SIX: Attach the Entry Section & Ladder to the Flu e
Stand and l an th Entry and Ladd r Ass mbly against th Upp r Flum .
Th ntry s ction has a small l ngth of 3/8” vinyl tubing and a conn ctor which will b us d
in th final ass mbly to conn ct to th vinyl tubing from th xit. (See Fig 16) Do not conn ct
th 3/8” vinyl tubing at this tim . It will b don aft r th slid is position d and mount d
to th d ck. G ntly mov th vinyl tubing from both s ctions to th sid . Align th flang s
and conn ct with only th bottom 3 bolts with hardwar from kit ADR-102-SS and anti-s iz .
(See Fig 17) Hand tight n only at this tim .
Fig. 16 Fig. 17

INSTALLATION MANUAL ADRENALINE™ SLIDE
14
ADR1-IM R v. 4/16 (ADR-INSTALL)
Fig. 18
STEP SEVEN: Position Slide Asse bly on Deck
First, s t th ladd r at 16˚ using a slop find r as shown in Figure 19. Th n adjust th ladd r
l v l sid to sid by placing a l v l against th outsid dg of th st ps as shown in Figure 20
Fig. 19 Fig. 20
L v l th long and short PVC l gs on both axis using a bubbl l v l as shown in Figure 21
Fig. 21

INSTALLATION MANUAL ADRENALINE™ SLIDE
15
ADR1-IM R v. 4/16 (ADR-INSTALL)
STEP EIGHT: Anchoring the Slide to the Deck
Ensur that th ass mbl d slid is in its corr ct and final position on th d ck.
Now that th slid is in its corr ct and final position, th 2 l gs ar plumb, and th ladd r
is at 16˚ slop , us th f t and th front p d stal as a t mplat to car fully mark th locations
for all th anchor bolts.
NOTE: Us th short mark r provid d.
DISASSEMBLY TO MOVE SLIDE
Sinc it is not possibl to drill th anchor bolt hol s with th slid in plac , and sinc th
slid is v ry long and h avy, it is b st now that th bolt hol s ar accurat ly mark d, to
disass mbl th Entry and Ladd r from th Upp r-Low r Flum and Exit s ctions. (Shown
in Figure 18 ) Using 3 p rsons, g ntly mov th Flum s-Exit ass mbly to on sid allowing
suffici nt room to drill th anchor bolt hol s. Do not l av th parts unass mbl d or l aning
on th ir sid for v ry long, as th y can warp.
Anchor bolts ar in hardwar kit ADR-104-SS. NOTE: there are 17 deck anchors (8-
3/8” x 2-3/4” and 9-3/8” x 3-1/2”), the 8 shorter anchors are used on the 2 round
pedestals, the 9 longer anchors are used for the exit and step pedestal. (See Figure 22)
Using a 3/8” masonry bit, drill th 17 hol s straight at 90˚ to th d ck surfac . DO NOT
drill compl t ly through th d ck.
Plac w dg anchors into th hol s and prop rly s at th m.
NOTE: Drill 3/8” hol s for 2 round p d stals 1-1/2” d p, l aving 1-1/4” abov d ck. Drill
3/8” hol s for xit s ction and st p p d stal 1-3/4” d p, l aving 1-3/4” abov d ck.
Fig. 22
REPOSITION AND REASSEMBLY OF SLIDE
Now that all 17 hol s hav b n drill d and th d ck anchor bolts ar in plac , r position
th slid onto th d ck starting with th upp r-low r flum and xit s ction. Car fully lift and
plac th upp r-low r flum and xit s ction ov r th anchor bolts.

INSTALLATION MANUAL ADRENALINE™ SLIDE
16
ADR1-IM R v. 4/16 (ADR-INSTALL)
STEP EIGHT: Anchoring the Slide to the Deck - CONT.
Position th ntry-st p ass mbly about 12” from th upp r flum . Whil holding th vinyl
tubing from th xit cut th tubing off about 1” back from th r d cap. Holding th tubing
will insur that it do sn’t fall back into th upp r flum s ction. Conn ct th tubing to th
coupl r and push any xc ss tubing back into th flum s ction. B car ful not to kink th
tubing or g t it caught b tw n conn ction flang s as th parts ar bolt d tog th r.
Car fully lift and plac th Entry and Ladd r s ction ov r th anchor bolts. Align th 5 flang
hol s b tw n th ntry and th upp r flum , and r p at th bolting instructions. Hand
tighten for now.
Plac a 3/8” flat wash r (hardwar kit ADR-104-SS), a lock wash r and a nut ov r th
anchor bolts and car fully tight n th nuts to s cur th slid to th d ck.
STEP NINE: Align ent of Flu e Sections
G ntly position th ass mbl d slid into its corr ct and final position on th pool d ck, align th
sliding surfac by adjusting th flum to flum alignm nt. (See Fig 23)
TIP: Th r is nough tol ranc in th flang conn ctions to provid a smooth and v n transition
of th sliding surfac b tw n th flum s ctions.
TIP: Onc th flum s ctions ar bolt d tog th r hand tight, th n g ntly push or pull on th
flum s ctions to nsur a smooth, v n alignm nt of th sliding surfac .
Starting with th xit s ction, tight n th two out r bolts in an alt rnating fashion whil main-
taining a smooth sliding surfac . R p at this proc ss for th oth r flang s as you mov up
th slid . Tight n all flang to flang conn ction bolts at this tim .
Fig. 23

INSTALLATION MANUAL ADRENALINE™ SLIDE
17
ADR1-IM R v. 4/16 (ADR-INSTALL)
STEP ELEVEN: Connect the Water Supply Syste
Conn ct th bottom 1” PVC Fl x Pip to th custom r install d wat r stub-up, as n c ssary.
It is r comm nd d that th provid d in-lin valv b install d b tw n th slid and th wat r
sourc so that th wat r flow can b adjust d as n c ssary.
STEP TEN: Tighten Leg Receiver Through Bolts
With th slid s cur d to th d ck and flum s align d and tight n d, tight n th six 3/8”x9-
1/2” bolts on th PVC l g to both flum s and ntry s ction.
Ch ck th sliding surfac on last tim and adjust as n c ssary. At this tim , ch ck and
r -tight n ALL SLIDE CONNECTIONS.
STEP TWELVE: Finishing Steps
• Install prot ctiv caps on all xpos d bolts.
• Turn wat r supply on and ch ck wat r flow.
• Cl an Slid and dispos of all d bris caus d by th installation.
NOTE: It is recommended that after several days of use, all visible bolted connections be
re-tightened as needed
FINAL INSPECTION / ANNUAL INSPECTION CHECK LIST:
1. R -m asur th d pth and width of th wat r in front of th slid as w ll as th slid ’s
xit h ight abov wat r to nsur th y conform to Diagrams A, B, and C on pag 4.
2. Ch ck th slid ’s position on th d ck and nsur it conforms to th diagrams on pag s 5-6.
3. Ensur th slid is s cur ly anchor d to th d ck and stabl .
4. Insp ct th runway for visibl cracks or t ars.
5. Insp ct th runway and nsur a smooth, v n sliding surfac . Ensur th gask ts
b tw n th flang s ar compr ss d uniformly.
6. Insp ct th runway for any wat r l aks and adjust wat r flow for v n wat r distribution
across sliding surfac . Ensur wat r do s not splash outsid th runway, and all wat r
running off th slid falls into th pool.
7. Insp ct th slid for any loos or corrod d fast n rs.
8. Ensur th r is a prot ctiv rubb r cap on all xpos d nuts and bolts.
9. Insp ct all st p-attachm nt points and nsur th st ps ar s at d on th nylon support
rods corr ctly.
10. Insp ct th ladd r handrails for rigidity and attachm nt. Can th y b pull d out of th ir
sock ts?
11. Insp ct th slid for sharp dg s or protrusions on th ladd r, d ck flang s, handrails
or runway.
12. Mak sur th slid warning lab l is s cur ly adh r d to th slid .
NOTE: this installation is not co plete until you, the installer, gives the owner’s anual
to the custo er and then reviews the intended use instructions with the .

INSTALLATION MANUAL ADRENALINE™ SLIDE
18
ADR1-IM R v. 4/16 (ADR-INSTALL)
ADRENALINE™ SLIDE CARE & MAINTENANCE:
Your slid r quir s p riodic maint nanc to k p it looking lik n w.
• Wash monthly or mor fr qu ntly, if n d d. B car ful to k p cl aning mat rial from
nt ring th pool.
• Wash with a mild soap such as hand dishwashing soap, avoid using strong cl an rs or
abrasiv s. Avoid strong alkalin (such as tri-sodium phosphat ) or highly acidic cl an rs.
Avoid bl ach and ammonia.
* These suggestions and data based on information believed to be reliable, from our raw materials
manufa turers. They are offered in good faith, but without guarantee, as onditions and methods
of use and pro edures are beyond our ontrol.
Wh n installing an Int r-Fab Adr nalin ™ slid using a pav r kit, you must nsur that all
standard installation r quir m nts ar m t. Th slid must b compatibl with th typ of
pool on th int nd d installation and all ANSI/NSPI-4 2007 r quir m nts must b m t.
R f r to installation manual.
Figure 24 illustrat s an xampl of th minimum concr t pads r comm nd d for th
Adr nalin ™ slid . Sp cific slid positions and concr t pad ori ntations may vary. Mak
sur to allow for wat r stub up location n ar th ladd r foot on th Adr nalin ™ slid wh n
pouring th concr t pad for th ladd r foot. In order to ensure proper placement, you
will need to set the slide up first to determine where the concrete pillars will be located
PAVER KIT INFO – ADRENALINE
Fig. 24