Holzhof OASIS XOA 100 User manual

OASIS XOA 100 line
OASIS XOA 100 line OASIS XOA 100 line
OASIS XOA 100 line
assembly instructions
assembly instructionsassembly instructions
assembly instructions

ASSEMBLY SEQUENCE
1. STRUTS AND PLATFORMS
2. PE ARCHWAYS
3. SLIDES 84
4. SLIDES 144
5. TUBE SLIDE
6. PARAPETS
7. PALMS
8. UNDERGROUND
LAYING/ANCHORAGE OF THE
STRUCTURE

KEY
• bolts insertion
• space
(a) support
(i) underground
Follow the layout for correct positioning of the bolts.

1. Fix the platform (1) to the struts (2), inserting the
relevant bolts into the holes on the wings at the corners
(as shown in the attached layout), as indicated in the
figure.
2. Repeat the operation for the other towers if necessary.
3. Once all of the structure has been fixed, insert other
TEFR screws into the empty holes in the wings (using the
same procedure as above) to give increased robustness;
first drill the struts with the Ø5 mm bit supplied.
NOTE c
olours and models represented are purely
representative.
Article
num.
Quantity
NAME
1 1 Oasis triangular platform
2 3 Oasis aluminium strut
3 2 PE nut protection cap
4 2 IS07089 Ø8 washer
5 2 M6,3x60 TEFR SCREW
6 2 PE cap

1) 4 x PE cap
2) 2 x M8 nut
3) 4 x M8 washer
4) 4 x PE nut protection cap
5) 2 x M8x40 HEX Screw
6) 1 x slide entrance panel
NOTA BENE the slide entrance panels have different inner shaping for the
slide depending on the height of the fixing panel. Check the indication
present on the panel itself.
1. Centre the slide entrance panel (6) between the struts and the platform
and start to fix the lower part of the panel to the platform by inserting the
necessary fixing bolts into the slots present on the edge of the platform.
NOTA BENE it
is recommended to fix
the bolts definitively and only insert
the caps once the correct positioning
of the elements has been verified.

NOTA BENE it is recommended to fix the
bolts definitively and only insert the caps once
the correct positioning of the elements has been
verified.
1) 6 x PE nut protection cap
2) 6 x M8 washer
3) 6 x M6 3x60 TEFR SCREW
4) 6 x PE cap
1.
Drill the struts using the
Ø
5 bit supplied.
2.
Fix the slide entrance panel to the struts using the
relevant bolts, as indicated in the figure.

1. Drill the small struts using the
Ø5 bit supplied.
2. Fix the slide to the small struts using the
relevant bolts as indicated in the figure.
1) 4 xPE cap
2) 4 x M6 3x80 TEFR SCREW
3) 4 x washer
NOTA BENE it is recommended to fix the
bolts definitively and only insert the caps
once the correct positioning of the
elements has been verified.

1. Fix the (2) tube slide body to the bracket using the relevant
bolts, as indicated in the figure.
The tube entrance must be positioned at the same height as the
platform (see figure 1).
NOTA BENE before proceeding with
fixing, drill the struts using the Ø5
mm bit supplied.
Article
num.
Quantity
NAME
1 6 PE nut protection cap
2 1 Oasis assembled tube slide
3 6 PE cap
4 6 IS07089 Ø8 washer
5 6 M6,3x100 TEFR SCREW

Arti
cle
num.
Quantity
NAME
1 1 PE bamboo parapet
2 4 PE nut protection cap
3 4 PE cap
4 4 IS07089 Ø8 washer
5 4 M6,3x100 TEFR SCREW
Fix the protection panel using the relevant bolts, as indicated in the
figure.
The lower part of the panel is adjacent t
o the upper part of the
platform.
NOTA BENE before proceeding with fixing, drill
the struts using the Ø5 mm bit supplied.

NOTA BENE Before proceeding with fixing, drill the struts using the
Ø5 mm bit supplied.
Fix the PE palm to the top of the strut, inserting the screw as indicated in the
figure.
NOTE colours and models represented are purely indicative.
M6
,
3x90 mm TEFR screw

1. Excavate a hole with Ø 30 cm and depth of 60 cm
2. Cast a first layer of con
crete with thickness of 10 cm.

3. When the concrete has set,
position the strut upright in the excavation
hole.
4. Complete concrete
casting as per layout.
5. When the concrete
has set, fill the
excavation hole by
compacting the infill
material up to the
finished ground level.

1. Excavate a
hole with diameter of 30 cm and depth of 60 cm
2. Cast a first layer of concrete with thickness of 10 cm.

3. When the concrete has set, position the slide bracket in the
excavation hole, checking the correct alignment of the lower
part of the slide with the finishedground level.

4. Complete concrete
casting as per layout.
5. When the concrete
has set, fill the
excavation hole by
compacting the infill
material up to the
finished ground level.

1.
1. 1.
1. A
AA
Attach the brackets (1) by introducing the followin
ttach the brackets (1) by introducing the followinttach the brackets (1) by introducing the followin
ttach the brackets (1) by introducing the followin
g in
g in g in
g in
sequence PE nut protection cap (2), M8 washer (3), M8x25
sequence PE nut protection cap (2), M8 washer (3), M8x25 sequence PE nut protection cap (2), M8 washer (3), M8x25
sequence PE nut protection cap (2), M8 washer (3), M8x25
hex screw
hex screwhex screw
hex screw (4), PE cap (5)
(4), PE cap (5)(4), PE cap (5)
(4), PE cap (5)
1. Excavate two holes with diameter of 30 cm and depth of 60 cm
NOTA BENE it is recommended to fix the
NOTA BENE it is recommended to fix the NOTA BENE it is recommended to fix the
NOTA BENE it is recommended to fix the
bolts definitively and only insert the caps
bolts definitively and only insert the caps bolts definitively and only insert the caps
bolts definitively and only insert the caps
once the correct p
once the correct ponce the correct p
once the correct positioning of the
ositioning of the ositioning of the
ositioning of the
elements has been verified.
elements has been verified.elements has been verified.
elements has been verified.
3. When the concrete has set, position the climbing board brackets in
the hole, checking the correct alignment of the lower part of the
climbing board with the finished ground level.
4. Complete concrete casting as per layout.
5. When the concrete has set, fill the hole by compacting the
infill material up to the finished ground level.
2. Cast a first layer of concrete with thickness of 10 cm.

1. Excavate two holes with diameter of 30 cm and depth of 60
cm as per layout.
2. Cast a first layer of concrete with thickness of 10 cm.

The measurements vary on the basis of the entrance to the slide
from a minimum of 20 to a maximum of 35 cm.

3. Complete concrete casting as per layout.
4. When the concrete has set, fill the h
ole by compacting the infill material up
to the finished ground level.

Article
num.
Quantity
NAME
1 1 Oasis support strut H.333
2 1
59x59x35 stainless steel angle
bracket
3 2 PE nut protection cap
4 1 IS07089 Ø8 washer
5 1 M6,3x80 TEFR screw
6 1 M10 self-locking screw anchor
7 1 M10 self-locking nut
8 1 Ø10 washer
9 2 PE cap
1. Position the strut and the angle bracket onto the support
surface, marking the position of the screw anchor.
2. Drill the support surface and position the screw anchor.
3. Fix the angle bracket to the support surface (if not
previously performed) using the relevant bolts, as indicated
in the figure.