Interlogix VE710 Assembly instructions

© 2019 UTC Fire & Security Americas Corporation, Inc. 1 / 4 P/N 149998999-1 (ML) • REV C • ISS 30MAY19
VE710 Alignment Tool Installation Sheet
EN
DE
FR
IT
NL
1
2
3
1 m

2 / 4 P/N 149998999-1 (ML) • REV C • ISS 30MAY19
EN: Installation Sheet
WARNING! Do not look into the laser beam.
The VE710 laser is classified by IEC60825-1 as
a Class 2 laser. Consequently the output power
is less than 1 mW. The eye’s blinking reflex is
fast enough to prevent any permanent damage
to the eye.
Aligning the beam and walk testing the detector:
1. Insert VE710 in the sub-frame of VE700 with the On/Off
switch facing the floor (Figure 1).
2. Connect to the COM port.
3. Turn on VE710.
4. The laser spot indicates the product alignment (Figure 1).
If this spot on the wall veers from the centre of the desired
detection area 1 m from the ground, then loosen the base
fixation screws (Figure 2) and use the three adjustment
screws in the base to realign it to the centre, as shown in
Figure 3. When the spot is correctly realigned, retighten
the base fixation screws.
5. Remove the alignment tool and replace the cover.
6. Carry out the walk test. Make sure that the red LED is On
after the walk test.
Regulatory information
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE
TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER”OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/ or scan the QR code.
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.utcfssecurityproducts.eu
DE: Installationsanweisungen
WARNUNG! Schauen Sie nicht in den
Laserstrahl.
Der VE710 Laser ist durch die IEC60825-1 Norm
als Klasse 2 Laser klassifiziert. Konsequenter
Weise beträgt die Ausgangsleistung weniger als
1 mW. Unter normalen Umständen wird das
menschliche Auge durch das reflexartige schnelle
Blinzeln vor dauerhaften Schädigungen
geschützt.
Ausrichtung des Erfassungsbereiches und Durchführung
eines Gehtests für den Melder:
1. Führen Sie das VE710 in den Unterrahmen ein, wobei der
Schalter On / Off in Richtung des Bodens zeigt (Abb. 1).
2. Schließen Sie es an den COM-Port an.
3. Schalten Sie das VE710 ein.
4. Der Laserpunkt gibt die Geräteausrichtung an (Abb. 1).
Wenn dieser Punkt auf der Wand vom Zentrum des
gewünschten Überwachungsbereiches 1 m über den
Boden abweicht, lösen Sie die Befestigungsschrauben
des Meldersockels (Abb. 2) und verwenden Sie zur
Ausrichtung des Laserpunkts die drei Einstellschrauben
wie in Abb. 3 dargestellt. Nachdem der Laserpunkt korrekt
eingestellt wurde, sind die Befestigungsschrauben des
Meldersockels wieder festzuziehen.
5. Entfernen Sie das Ausrichtungswerkzeug, und setzen Sie
die 1 m Abdeckung wieder ein.
6. Führen Sie den Gehtest durch. Stellen Sie sicher, dass die
rote LED nach dem Gehtest eingeschaltet ist.
Zertifizierung und Einhaltung
Hersteller
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Autorisierter EU-Herstellungsrepräsentant:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Niederlande
Produktwarnungen
und Haftungs-
ausschluss
DIESE PRODUKTE SIND FÜR DEN VERKAUF
AN UND DIE INSTALLATION DURCH
QUALIFIZIERTES PERSONAL VORGESEHEN.
UTC FIRE & SECURITY ÜBERNIMMT
KEINERLEI GEWÄHRLEISTUNG DAFÜR, DASS
NATÜRLICHE ODER JURISTISCHE
PERSONEN, DIE UNSERE PRODUKTE
ERWERBEN, SOWIE „AUTORISIERTE
HÄNDLER“ ODER „AUTORISIERTE
WIEDERVERKÄUFER“ ÜBER DIE
ERFORDERLICHE QUALIFIKATION UND
ERFAHRUNG VERFÜGEN, UM
BRANDSCHUTZ- ODER
SICHERHEITSTECHNISCHE PRODUKTE
ORDNUNGSGEMÄSS ZU INSTALLIEREN.
Weitere Informationen zu Haftungsausschlüssen
sowie zur Produktsicherheit finden Sie unter
https://firesecurityproducts.com/policy/product-
warning/, oder scannen Sie den QR-Code.
Kontaktinformation
www.utcfireandsecurity.com oder www.interlogix.com

P/N 149998999-1 (ML) • REV C • ISS 30MAY19 3 / 4
Kontaktinformationen für den Kundendienst finden Sie unter
www.utcfssecurityproducts.de
FR: Instructions d’installation
AVERTISSEMENT ! Ne regardez pas
directement dans le faisceau du laser.
Le laser du VE710 est de classe 2 par
l’IEC60825-1; en conséquence, la puissance de
sortie du laser est de 1mW. Le réflexe de
clignotement de l’œil sera suffisamment rapide
pour éviter tout dommage irréversible à l’œil.
Alignement du faisceau et test de marche du détecteur :
1. Insérez le VE710 dans le sous-cadre avec le commutateur
orienté vers le bas (figure 1).
2. Connectez-vous au port COM.
3. Allumez le VE710.
4. Le point du laser indique l’alignement du produit (figure 1).
Si ce point sur le mur vire du centre de la zone de
détection souhaitée (1 m à partir du sol), enlever les vis de
fixation de la base (figure 2) utilisez les trois vis de réglage
de la base pour l’aligner de nouveau sur le centre, comme
indiqué à la figure 3. Lorsque le spot est aligné
correctement, replacer les vis de fixation de la base.
5. Retirez l’outil d’alignement et remettez en place le cache.
6. Effectuez le test de marche. Assurez-vous que le voyant
lumineux est allumé après le test de marche.
Information réglementaire
Fabricant
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, E-U
Représentant européen agréé de la fabrication :
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Pays-Bas
Avertissements et
avis de non-
responsabilité
CES PRODUITS SONT DESTINÉS À DES
PROFESSIONNELS EXPÉRIMENTÉS, QUI
DOIVENT ÉGALEMENT SE CHARGER DE LEUR
INSTALLATION. UTC FIRE & SECURITY NE
PEUT GARANTIR QU’UNE PERSONNE OU
ENTITÉ FAISANT L’ACQUISITION DE CEUX-CI,
Y COMPRIS UN REVENDEUR AGRÉÉ,
DISPOSE DE LA FORMATION OU DE
L’EXPÉRIENCE REQUISE POUR PROCÉDER
ÀCETTE MÊME INSTALLATION DE FAÇON
APPROPRIÉE.
Pour obtenir des informations supplémentaires sur
les garanties et la sécurité, rendez-vous
àl’adresse
https://firesecurityproducts.com/policy/product-
warning/ ou scannez le code QR.
Contact
www.utcfireandsecurity.com ou www.interlogix.com
Pour contacter l'assistance clientèle, voir
www.utcfssecurityproducts.fr/mail_support.htm
IT: Istruzioni d’installazione
ATTENZIONE! Non guardare il raggio laser.
Il VE710 è classificato dalle IEC60825-1 come
laser di Classe 2. Di conseguenza la potenza di
uscita è minore di 1 mW. Il riflesso
incondizionato della palpebra dell’occhio è
sufficientemente veloce per prevenire qualsiasi
danno permanente all’occhio.
Allineamento della tenda centrale e test di copertura del
rivelatore:
1. Inserire il VE710 nell’apposito alloggiamento, con
l’interruttore On/Off rivolto verso il pavimento (fig. 1).
2. Collegarlo alla porta COM.
3. Accendere il VE710.
4. Il punto luminoso generato dal laser indica l’allineamento
del prodotto (fig. 1). Se il punto luminoso sulla parete si
discosta dal centro dell’area di rivelazione desiderata e da
1 m da terra, allentare le viti di fissaggio della base (fig. 2)
e utilizzare le tre viti di regolazione poste nella base per
riallinearlo al centro (fig. 3). Quando il punto luminoso
ècorrettamente allineato serrare le viti di fissaggio della
base.
5. Rimuovere lo strumento di allineamento e riposizionare il
coperchio.
6. Eseguire il test di copertura. Assicurarsi che il LED rosso
sia acceso dopo il test di copertura.
Certificazione e conformità
Produttore
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092,
Stati Uniti
Rappresentante autorizzato per l'UE:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Paesi Bassi
Avvertenze sul
prodotto
e dichiarazioni di
non responsabilità
QUESTI PRODOTTI SONO DESTINATI ALLA
VENDITA A, E DEVONO ESSERE MONTATI
DA, UN ESPERTO QUALIFICATO. UTC FIRE
& SECURITY NON PUÒ GARANTIRE CHE LE
PERSONE O GLI ENTI CHE ACQUISTANO
I SUOI PRODOTTI, COMPRESI
I “RIVENDITORI AUTORIZZATI”,
DISPONGANO DELLA FORMAZIONE
O ESPERIENZA ADEGUATE PER ESEGUIRE
LA CORRETTA INSTALLAZIONE DI
PRODOTTI PER LA SICUREZZA E PER LA
PROTEZIONE ANTINCENDIO.
Per ulteriori informazioni sulle esclusioni di
garanzia e sulla sicurezza dei prodotti,
consultare il sito
https://firesecurityproducts.com/policy/product-
warning/ oppure eseguire la scansione del
codice QR.
Contatto per informazioni
www.utcfireandsecurity.com o www.interlogix.com
Per l'assistenza clienti, vedere www.utcfssecurityproducts.it

4 / 4 P/N 149998999-1 (ML) • REV C • ISS 30MAY19
NL: Installatie instructies
WAARSCHUWING! Kijk nooit recht in de
laserstraal.
De VE 700 laser is gekeurd volgens IEC60825-1
als een klasse 2 laser, het continue uitgangs
vermogen van de laser is lager dan 1 mW. De
oog reactie (knipperen) is snel genoeg om
permanente beschadiging te voorkomen.
De Laserbundel uitlijnen en de looptest van de detector
uitvoeren:
1. Plaats de VE710 in de geleiders, met de schakelaar
Aan/Uit naar de grond gericht ( fig. 1).
2. Sluit de connector aan op de ingang.
3. Schakel de VE710 in.
4. De laserstip geeft de afregeling van de detector aan
(fig. 2). Als die stip op de wand afwijkt van het midden van
het gewenste detectiegebied, gebruikt u de drie
bijstelschroeven in de basis om het detectie gebied weer
in het midden uit te lijnen, zoals in fig. 3 is weergegeven.
5. Verwijder het uitlijningsgereedschap en plaats de deksel
terug.
6. Voer de looptest uit. Controleer dat de rode LED AAN is
gedurende de looptest.
Algemene Informatie
Fabrikant
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Geautoriseerde EU-vertegenwoordiger:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Nederland
Waarschuwingen
en disclaimers met
betrekking tot de
producten
DEZE PRODUCTEN ZIJN BEDOELD VOOR
VERKOOP AAN EN INSTALLATIE DOOR
GEKWALIFICEERDE BEROEPSKRACHTEN.
UTC FIRE & SECURITY GEVEN GEEN
GARANTIE DAT EEN PERSOON OF ENTITEIT
DIE DIENS PRODUCTEN AANSCHAFT,
WAARONDER “GEAUTORISEERDE DEALERS”
OF “GEAUTORISEERDE WEDERVERKOPERS”,
OP DE JUISTE WIJZE ZIJN OPGELEID OF
VOLDOENDE ERVARING HEBBEN OM
PRODUCTEN MET BETREKKING TOT BRAND
EN BEVEILIGING OP DE JUISTE WIJZE TE
INSTALLEREN.
Zie voor meer informatie over garantiebepalingen
en productveiligheid
https://firesecurityproducts.com/policy/product-
warning/ of scan de QR-code.
Contact informatie
www.utcfireandsecurity.com of www.interlogix.com
Voor klantenondersteuning, zie www.utcfssecurityproducts.nl