Renishaw XK10 User manual

XK10 alignment laser user guide
User guide
F-9936-0721-02-A

XK10 alignment laser system
Legal information
Safety
Before using the laser system, please consult the laser safety information booklet.
Disclaimer
WHILE CONSIDERABLE EFFORT WAS MADE TO VERIFY THE ACCURACY
OF THIS DOCUMENT AT PUBLICATION, ALL WARRANTIES, CONDITIONS,
REPRESENTATIONS AND LIABILITY, HOWSOEVER ARISING, ARE
EXCLUDED TO THE EXTENT PERMITTED BY LAW.
RENISHAW RESERVES THE RIGHT TO MAKE CHANGES TO THIS
DOCUMENT AND TO THE EQUIPMENT, AND/OR SOFTWARE AND THE
SPECIFICATION DESCRIBED HEREIN WITHOUT OBLIGATION TO PROVIDE
NOTICE OF SUCH CHANGES.
Trade marks
RENISHAW®and the probe symbol are registered trade marks of Renishaw plc.
Renishaw product names, designations and the mark ‘apply innovation’ are
trade marks of Renishaw plc or its subsidiaries. Other brand, product or company
names are trade marks of their respective owners.
Terms and conditions of warranty
Unless you and Renishaw have agreed and signed a separate written agreement,
the equipment and/or software are sold subject to the Renishaw Standard Terms
and Conditions supplied with such equipment and/or software, or available on
request from your local Renishaw office.
Renishaw warrants its equipment and software for a limited period (as set out in
the Standard Terms and Conditions), provided that they are installed and used
exactly as defined in associated Renishaw documentation.You should consult
these Standard Terms and Conditions to find out the full details of your warranty.
Equipment and/or software purchased by you from a third-party supplier is subject
to separate terms and conditions supplied with such equipment and/or software.
You should contact your third-party supplier for details.
Copyright
© 2019-2020 Renishaw plc. All rights reserved.
This document may not be copied or reproduced in whole or in part, or transferred
to any other media or language, by any means without the written prior
permission of Renishaw plc.
The publication of material within this document does not imply freedom from the
patent rights of Renishaw plc.
Renishaw part no: F-9936-0721-02-A
Issued: 07.2020

XK10 alignment laser system
Legal information
International regulations and conformance
EU compliance
Renishaw plc declares under its sole responsibility that the XK10
system is in conformity with all relevant Union legislation. The full
text of the EU declaration of conformity is available at upon request.
WEEE
The use of this symbol on Renishaw products and/or accompanying
documentation indicates that the product should not be mixed with
general household waste upon disposal. It is the responsibility of the end
user to dispose of this product at a designated collection point for waste
electrical and electronic equipment (WEEE) to enable reuse or recycling.
Correct disposal of this product will help to save valuable resources
and prevent potential negative effects on the environment. For more
information, please contact your local waste disposal service or
Renishaw distributor.
Battery disposal
Please see the relevant battery manufacturer’s website for further information
(see Battery safety – Transportation).
The use of this symbol on the batteries, packaging or accompanying documents
indicates that used batteries should not be mixed with general household waste.
Please dispose of the used batteries at a designated collection point. This will
prevent potential negative effects on the environment and human health which
could otherwise arise from inappropriate waste handling. Please contact your
local authority or waste disposal service concerning the separate collection
and disposal of batteries. All lithium and rechargeable batteries must be fully
discharged or protected from short circuiting prior to disposal.
Packaging
Packaging
components
Material 94/62/EC code 94/62/EC number
Outer box Cardboard PAP 20
Inserts Cardboard PAP 20
Bag Low density polyethylene LDPE 4
REACH regulation
Information required by Article 33(1) of Regulation (EC) No. 1907/2006
(“REACH”) relating to products containing substances of very high concern
(SVHCs) is available at: www.renishaw.com/REACH
RoHS compliance
Compliant with EC directive 2011/65/EU (RoHS)
China RoHS
For more information, on China RoHS visit: www.renishaw.com/calchinarohs

XK10 alignment laser system
Radio communications
The wireless communication module used within the XK10 alignment laser
system is pre-approved in a number of regions including EU, EFTA countries,
USA and Canada.
Module manufacturer: ublox
Part number: OBS421i
FCC ID: PVH0946
Module ID No: cB-0946
Further radio approval country specific statements can be found below:
China
本设备包含型号核准代码为CMIIT ID: 2015DJ1181的无线电发射模块
Taiwan
低功率電波輻性電機管理辦法
第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不
得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾
現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信
規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波
輻射性電機設備之干擾 。

XK10 alignment laser system
Legal information
USA and Canadian regulations
FCC
Information to the user (47CFR:2001 part 15.19)
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
Information to the user (47CFR:2001 part 15.105)
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not used in accordance with this user
guide, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which
case you will be required to correct the interference at your own expense.
Information to the user (47CFR:2001 part 15.21)
The user is cautioned that any changes or modifications, not expressly approved
by Renishaw plc or authorised representative, could void the user’s authority to
operate the equipment.
Special accessories (47CFR:2001 part 15.27)
The user is also cautioned that any peripheral device installed with this
equipment, such as a computer, must be connected with a high-quality shielded
cable to ensure compliance with FCC limits.
Canada – Industry Canada (IC)
This device complies with RSS 210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause
undesired operation of this device.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire d’interference et (2) l’utilisateur du dispositif doit étre
prêt à accepter toute interference radioélectrique reçu, même si celle-ci est
susceptible de compromettre le fonctionnement du dispositif.