LUDECA MASTERLIGN User manual

4. Results
Coupling Results
• Press until appears.Press or
or to toggle through offset and
angular misalignment.
(+) Positive coupling offset p
(-) Negative coupling offset q
(+) Positive coupling gap
(-) Negative coupling gap
Repeat sections 3 and 4 to establish repeatability.
Foot Corrections
• Press until appears. Press or
or to toggle through vertical
shimming and horizontal move corrections.
Arrows show direction of move or shimming. Apply
correction to blinking foot.
600 5.0 9.0 10.0 15.0 1.8 3.0
900 3.0 6.0 7.0 10.0 1.2 2.0
1200 2.5 4.0 5.0 8.0 0.9 1.5
1800 2.0 3.0 3.0 5.0 0.6 1.0
3600 1.0 1.5 2.0 3.0 0.3 0.5
7200 0.5 1.0 1.0 2.0 0.2 0.3
2. Enter dimensions
•1. Laser to prism
(Arrow point to hash mark "φ" on prism)
(Center-to-centerofsupportposts)
•2. Laser to center of coupling
(Center of flex planes)
•3. Working diameter 10"
(Couplingdiameter) (Defaultvalue)
•4. Laser to front foot
•5. Front foot to back foot
1. Mount MASTERLIGN®
and switch on
Stationary
Machine MTBM
(Machine To
Be Moved)
All Speeds: Maximum Soft Foot Reading 2 mils.
Use OEM or in-house tolerances if available.
Tolerances for Shaft Alignment
Offset
(mils)
Excellent Acceptable
RPM Gap
(mils/10")
Excellent Acceptable
Spacer Shaft
(mils/inch)
Excellent Acceptable
3. Measure
• Adjustprismsothatlaserbeamstrikescenter
of the prism cap cross hair.
• Remove cap.
• Adjust prism until coordinates are close
to 00.
•will appear on the screen.
• Rotate shafts at least 75°.
5. Move
• Rotate shafts until 45°appears (±4°)
• Adjust beam close to00 if necessary.
• When appears press .
• Loosen bolts.
• Move machine horizontally into alignment.
• Retighten bolts.
• Repeat Sections 3 and 4.
Order No. 01-199-01
©1999 LUDECA, INC. Masterlign and InfiniRange are registered trademarks of
Prueftechnik AG.
Resume: You can resume where you last left
off by pressing .

‘Results’ Default
• Factory default is Coupling Results.
• Press to toggle between and .
Press to confirm selection.
Storing and Printing Data
Saves file
Opens file
Prints a report
Soft Foot
• Position shafts at either 90° or 270° (±4°).
• Adjust beam close to 00 if necessary.
Press . (Not necessary if "----" appears.)
• Press then loosen the bolt, press
to record value then tighten bolt.
• Press or to move to the next foot.
Follow this procedure for all remaining feet and
correct soft foot if greater than 0.002".
InfiniRange®
•If or appear during rotation,
turn shafts back until numbers reappear.
(
InfiniRange then starts automatically.)
• Adjust beam close to 00 and press .
• Proceed with measurement.
Note: You may initiate InfiniRange manually at any
time by pressing .
MASTERLIGN®
Quick Reference
Version 1.1x
(Measurement Range Extension)
LUDECA, Inc.
1425 N.W. 88th Avenue, Miami, FL 33172
Phone: [phone] • Fax [phone]
[email protected] • www.ludeca.com
Visit us at: www.LaserAlignment.Net
Voelzow & Company, Inc.
P.O. Box 158 • Wingate, NC 28174
704-233-9222 • Fax [phone]
E-mail: [email protected]
Web: www.LaserAlignment.net