Interpump Group GENERAL PUMP DLTG12E User manual

GENERAL PUMP A member of the Interpump Group
DLTG12E
ACCESSORIES ACCESSORIES
High-Pressure Extendable Wand
General Pump
is a member of
the Interpump Group
Ref 310100 Rev. B
08-18
• All Aluminum poles
• High strength glass lled Nylon gun housing
• All brass gun valve
• Non-sticking dissimilar collet material

GENERAL PUMP A member of the Interpump Group
Thank you for purchasing an extension wand from General Pump.
With proper care your new extension wand will give you years of reliable service.
Your safety is important to us.
Please read and make sure you understand all of the safety warnings
and precautions prior to using your extension wand.
If you have any questions regarding the safe operation of your extension wand
please contact our Technical Support Team at 1-888-474-5487
Ref 310100 Rev. B
08-18
Page 2 of 6

GENERAL PUMP A member of the Interpump Group
SPECIFICATIONS*
Wand Model DLTG12E
Maximum Volume 6.6 GPM
Maximum Gun Pressure 2,600 PSI
Maximum Fluid Temperature 120ºF
Shipping Weight 5.6 lb
Dimensions - Retracted 48.8” L x 6" W
THE USER OF THIS ACCESSORY IS RESPONSIBLE FOR READING, UNDERSTANDING,
AND FOLLOWING ALL WARNINGS AND PRECAUTIONS PRIOR TO OPERATION.
FAILURE TO FOLLOW ALL WARNINGS AND PRECAUTIONS MAY RESULT IN PROPERTY
DAMAGE, SERIOUS PERSONAL INJURY, OR DEATH.
STOP
Ref 310100 Rev. B
08-18
• NEVER use near power lines.
• NEVER extend or retract wand while spraying or while under pressure. Stop the equipment
and relieve pressure before making any adjustments to the wand.
• NEVER change nozzles or accessories while under pressure. Stop the equipment
and relieve pressure before making any changes.
• NEVER use while on ladders or scaffolding.
• NEVER use with unapproved accessories.
• NEVER exceed rated pressure or volume.
• NEVER use high-pressure to clean persons or animals.
• NEVER remove or alter warning labels or identification tags.
• NEVER use wand if damaged.
Page 3 of 6

GENERAL PUMP A member of the Interpump Group
Ref 310100 Rev. B
08-18
• NEVER use wand if damaged.
• ALWAYS read, understand, and follow operation instructions.
• ALWAYS make certain area is clear of obstructions or hazards.
• ALWAYS maintain proper balance and control of extension wand.
This label appears on the extension wand. Do not remove or deface.
If the label becomes damaged or unreadable please call for a no charge replacement.
Page 4 of 6
OPERATION INSTRUCTIONS
Read, understand, and follow ALL safety guidelines and operation instructions prior to use.
To use your extension wand:
Connect the outlet of your pressure washer to the inlet port of the trigger gun of the Giraffe
extension wand using appropriate quick couplers or fittings rated to handle high pressure.
Do NOT bypass, disable, or remove the trigger gun.
DO NOT use pliers, pipe wrenches, etc. to tighten as it will cause the collet to seize to the
threaded plastic housing. HAND TIGHTEN ONLY!
The extension wand may be used fully retracted or fully extended or any point in between. Caution
must be used when the wand is extended as the reaction force of the nozzle spraying will cause
the wand to flex. Make absolutely certain that there are no power lines or sources of
electrical power within 10 feet of the lance at any time.
Contact with power transmission lines can cause fatal electrocution!

GENERAL PUMP A member of the Interpump Group
OPERATION INSTRUCTIONS
Caution: Do not extend or retract your extension wand while spraying or while under pressure.
Stop the equipment and relieve any pressure before making adjustments to the extension wand
or changing nozzles.
To extend the wand:
Loosen the brown lock rings and pull the wand out to the desired length. Re-tighten the lock rings
to hold the wand at the desired length.
To retract the wand:
Loosen the brown lock rings and slide the extension segment into the wand until the desired
length is reached and re-tighten the lock rings to hold the extension segments in place.
To begin spraying:
Start the pressure washer.
Raise the wand and keep the nozzle at least ten feet away from the surface to be cleaned. Keep
the extension wand clear of power lines.
Squeeze the trigger to begin spraying, maintain stable footing, and move the wand in to the
surface to be cleaned.
Caution: Except in cases of emergency, do not release the trigger near any surfaces.
To stop spraying:
Before releasing the trigger gun move the nozzle at least ten feet away from the surface being
cleaned and make sure you have solid footing. The wand will rebound when the trigger is
released or if pressure is lost. USE EXTREME CAUTION when working on or near fragile
surfaces as there may be enough force to damage surfaces or break windows. Keep clear of
power lines. When you are clear of the work surface and in a safe area - release the trigger.
Ref 310100 Rev. B
08-18
Page 5 of 6

GENERAL PUMP A member of the Interpump Group
Ref 310100 Rev. B
08-18
Page 6 of 6
EXPLODED VIEW & PARTS LIST
DLTG12E
ITEM PART # DESCRIPTION QTY
1DG2600TS12
GUN, TW, LOW PRESSURE 1
22550220 TUBE, TW, 24 OD 1
32550222 TUBE, TW, 28 OD 1
4 2550221 TUBE, TW, 20 OD 1
5 2550223 TUBE, TW, 32 OD 1
62660365 COLLET, NUT, 20MM 1
72660366 COLLET, SCREW, 20MM 1
82660367 COLLET, NUT, 24MM 1
9 2660368 COLLET, SCREW, 24MM 1
10 2660369 COLLET, NUT, 28MM 1
11 2660370 COLLET, SCREW, 28MM 1
12 2103342
ASSY, HOSE, LOW PRESSURE 1
13 2400000 LABEL 3
14 GPC0058 LABEL, WARNING 1
15 2660371 GROMMET, TW, 32MM 1
16 2530152 FITTING, UNION 1
17 2200004 SCREW, M4 2
18 2203506 WASHER, LOCK 2
19 D10002 COUPLER, 1/4 QC 1
*Label and hose not shown
DG2600TS12
ITEM PART # DESCRIPTION QTY
12452028
BODY, VALVE 1
22550219 TUBE, INLET 1
3 2660362 HOUSING, GUN, LEFT 1
4 2520159 PIN, VALVE, GUN 1
5 2701080 O-RING 1
62510259 PLUG, VALVE, GUN 1
7 2720036 SPRING, VALVE, GUN 1
82660364 TRIGGER 1
92520010 STRIKER 1
10 2660026 TRIGGER, LOCK 1
11 2660363 HOUSING, GUN, RIGHT 1
12 2200002
SCREW 12
13 2520161 BALL 1
14 2510260 WASHER, BRASS 1
15 2520160 SEAT, GUN 1
16 2701082 O-RING 1
17 2701081 O-RING 1
18 2510007 FITTING, INLET, GUN 1
19 2710030 WASHER, TEFLON 1