Interton TV Streamer User manual

User Guide
Interton TV Streamer

2 3
Statement:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must ac-
cept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communi-
cations.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
Welcome
Congratulations on your purchase of a Interton TV Streamer.
Interton TV Streamer will provide you with high quality streamed
audio from your TV, HiFi stereo, personal computer or similar de-
vice directly to your hearing instruments.
Please read this manual carefully to fully benefit from the Interton
TV Streamer. Ask your hearing care professional if you have any
questions.
For your safety, carefully read the chapter Important Information,
on pages 24-25
FCC ID: X26SAS-2

4 5
National restrictions:
Norway: You are not allowed to operate the equipment within 20
km of the centre of Ny Ålesund.
France: You are not allowed to operate the equipment outdoors.
Italy: Product is for private use. You are not allowed to operate the
equipment outside own premises.
This product is in compliance with the following regulatory stan-
dards:
In EU: The device conforms to the Essential Requirements ac-
cording to - Annex I of Council Directive 93/42/EEC for medical
devices (MDD) and essential requirements and other relevant
provisions of Directive 1999/5/EC (R&TTE). The declaration of
conformity may be consulted at www.interton.com.
In US: FCC CFR 47 Part 15, subpart C, section 15.247
Other identified applicable international regulatory requirements
in countries outside EU and US. Please refer to local country
requirements for these areas.
Products are categorized as receiver class 2 according to
EN 300 328
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Changes or modifications can void the user’s authority to operate
the equipment.
Intended use
IntertonTV Streamerisintended toenable2.4GHz wireless hearing
instrument users to better follow TV or other audio programs. The
essential performance of the Interton TV Streamer is to transfer sig-
nalsfromaTVsetorotheraudiodevicetoa2.4GHzwirelesshearing
instrument.
List of countries
Products are intended for sale in countries within European Eco-
nomic Area as well as Switzerland.

6 7
Contents
Description ......................................8-9
Getting Started ..................................10-17
Pairing to your hearing instruments.................. 18-19
Start and stop streaming .........................20-22
Controls ...................................... 23-24
Important Information ............................ 24-25
Technical specifications .............................26
Warranty .........................................26
Troubleshooting guide ...........................28-35
Notes ...........................................36

12
11
8
124
5
3
910
67
8 9
6 Increase volume
7 Decrease volume
8 Channel indicator
9 Power light (green)
10 Activity light (amber)
11 Wall plug
12 Mini-USB plug
Description
1 Mono / Stereo control
2 Left Audio connector
3 Right Audio connector
4 Mini-USB connector
5 Pairing button

10 11
Note: With this installation, most TVs will send sound to
both hearing instruments and speakers simultaneously.
On some TVs you can adjust the balance between the
AUDIO OUT and the speakers – consult your TV manual
for instructions.
Getting Started
Installing Interton TV Streamer
Depending on your TV, HiFi stereo, Computer or other audio
setup, the installation for Interton TV Streamer may differ. The fol-
lowing steps will guide you through the pairing and connecting
process, which can be easily accomplished by almost anyone.
Start with connecting the cables and finish by pairing Interton TV
Streamer to your hearing instruments.
Connect audio cables to Interton TV Streamer. For TV, HiFi Ste-
reo and Computer
1. Connect the power supply supplied by GN Hearing to the
wall socket and insert the cable to the Mini-USB socket on
Interton TV Streamer
2. Connect the red and white plug of the audio cord into the red
and white plugs on Interton TV Streamer
3. Plug the other end of the red and white audio cord in the
”AUDIO OUT” terminal on the TV
4. The ”AUDIO OUT” is usually marked ”L – R” for left and right,
and ”AUDIO OUT” and can be found on the back of the TV.
Alternatively you can plug this cable into your HiFi Stereo.

12 13
3. Connect the Jack adapter on the other end of the audio
cable
4. Plug the Jack adapter into the TVs ”HEADPHONE” output
terminal, or alternatively in your computers’ audio terminal.
In the packaging box you will find screws for mounting the
streamer on a wall. Instead of using screws, you can also
velcro the streamer on the side or on top of the TV. For best
performance, the TV streamer should be placed vertically, either
mounted on the wall or placed in the table stand that comes with
the packaging.
Alternative audio cable installations:
If connecting Interton TV Streamer to the AUDIO OUTPUT jack is
not possible on your TV, there are alternative installation possibili-
ties: Jack Adapter, Scart adapter
Jack adapter – for TV and Computer:
1. Connect the power supply to the wall socket and insert the
cable to the Mini-USB socket on Interton TV Streamer
2. Connect the red and white plug of the audio cord into the red
and white plugs on Interton TV Streamer

14 15
Digtal to analog audio converter
Should there only be a digital port in your TV, you will need a
‘digital to analog audio converter’ and a Toslink optical cable to
connect Interton TV Streamer to your TV. Consult your TV techni-
cian for these 2 items.
1. Connect the power supply to the wall socket and insert the
cable to the Mini-USB socket on Interton TV Streamer
2. Connect the red and white plug of the audio cord into the red
and white plugs on Interton TV Streamer
3. Connect the Digital to Analog Audio Converter to the other
end of the audio cable.
4. Connect the Digital to Analog Audio Converter’s power supply
to the converter and plug into wall socket.
5. Connect the Digital to Analog Audio converter to the television
using a Toslink Optical cable. Plug one end of the cable to the
converter and the other end to the digital audio output port on
the television.
Note: The HEADPHONE output terminal is usually located
on the side or front of the TV. When using the HEAD-
PHONE terminal, usually only the person wearing the
hearing instruments will hear the sound, and the TV speakers are
muted. If it is not desired that speakers are muted, please refer
to the first installation, or the one below for the scart adapter.
Your TV may support speakers and HEADPHONE being on simul-
taneously, check your TV manual for instructions.
Scart adapter – for TV:
1. Connect the power supply to
the wall socket and insert the
cable to the Mini-USB socket
on Interton TV Streamer
2. Connect the red and white plug
of the audio cord into the red
and white plugs on Interton TV
Streamer
3. Connect the Scart adapter on
the other end of the audio cable
4. Plug the Scart adapter into the TVs Scart terminal
Note: The Scart output terminal is usually located on the
back or side of the TV or DVD. When using this terminal,
the Video port of your TV is usually set as the output for
the sound. Consult your TV manual if you need to make changes
on the sound transfer.

16 17

18 19
3. While pairing mode is activated, close the battery doors of
both hearing instruments and make sure they are ON. (If the
amber activity light turns off before the hearing instruments
are turned on, pairing will not be completed.) A successful
pairing will be indicated by an audible melody played in both
hearing instruments. You are now ready to use the Interton TV!
Pairing to a 2nd or 3rd Interton TV Streamer unit
It is possible to pair up to three Interton TV Streamer units with
a given pair of hearing instruments. To pair a second Interton TV
Streamer, press the pairing button of the second unit two times,
which will illuminate the channel indicator (8 on page 9) at number
2, and then close the battery doors on the hearing instruments.
A third Interton TV Streamer unit can be paired by pressing the
pairing button three times and completing the procedure as
described above.
Pairing to your hearing instruments
Note! The following information is intended primarily
for your hearing care professional, who in most cases will
complete the tasks that are necessary before the Interton
TV Streamer can be used with your hearing instruments. How-
ever, the process is designed to be simple and should be easily
accomplished by almost anyone.
Pairing is the process of setting up an exclusive communication
between your hearing instruments and your Interton TV Stream-
er. Your hearing care practitioner can set up pairing during the
fitting of your hearing instruments. Alternatively, you can follow
the below steps to pair your hearing instruments to Interton TV
Streamer:
1. Make sure Interton TV Streamer is plugged in to a wall socket
and that the green power light is ON. Your hearing instruments
must be off – open the battery door.
2. Press the pairing button on Interton TV Streamer (5 on page
8) one time. This will activate the amber activity light (10 on
page 9) indicating that pairing mode has been activated. Also,
channel indicator light number 1 (8 on page 9) will be turned
on when the pairing button has been pressed only once. Pair-
ing mode will be activated for 20 seconds.