Intex Marketing HT30221 User manual

114
BS
(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
OWNER’S MANUAL
Electric Pool Heater
Model HT30221
230 V~, 50 Hz, 2800 W, IP25
Max. Water Temperature 35oC
IMPORTANT
SAFETY RULES
Read, Understand, and Follow
all Instructions Carefully before
Installing and using this Product.
Don’t forget to try these other fine Intex products: Pools, Pool
Accessories, Inflatable Pools and In-Home Toys, Airbeds and Boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual without notice.
For illustrative purposes only.
©2015 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com 114-*BS-R0-1608

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 2
Warnings................................................................................ 3
Parts Reference..................................................................... 4
Set Up Instructions............................................................... 5-8
Operating Time Table............................................................ 8
Electric Pool Heater
Stationary Mounting Option................................................. 9
Pool Care and Chemicals..................................................... 10
Long Term Storage................................................................ 10
Troubleshooting Guide......................................................... 11
Common Pool Problems....................................................... 12
General Aquatic Safety......................................................... 12
Limited Warranty................................................................... 13
Filter Pump Flow Rate Requirement:
500 - 2500 gallons/hour (1893 - 9464 liters/hour)
Working Water Temperature:
63 degrees Fahrenheit (17 degrees Celsius) to 95 degrees
Fahrenheit (35 degrees Celsius)
Suitable to be used for pool with water capacity:
below 4500 gallons (17033 liters)
Rectangular Length x Width x Average Depth x 7.5 Length x Width x Average Depth
Circular Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79
Oval Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80
Types of Pool Gallons
(pool size in feet) Cubic Meters
(pool size in meters)
TABLE OF CONTENTS

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 3
•
To reduce the risk of injury, do not permit children to use this product. Always supervise children and those with disabilities.
•Do not bury electrical cord. Locate cord where it will not be damaged by lawn mowers, hedge trimmers, and other
equipment.
•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
•To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect
unit to electric supply; provide a properly located outlet.
•Provide a dedicated electrical outlet socket with a rating of 16 Amp. or more. Make sure the RCD plug fit tightly and
securely into the electrical outlet socket. If not sure contact a qualified electrician.
•Assembly and disassembly by adults only.
•Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
• Position this product away from pool to prevent a child from climbing on product to access the pool.
•Children must stay away from this product and electrical cord(s).
•Do not operate this product when pool is occupied.
•Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to
the product.
•Always position the pool heater below the level of the pool hose connection during use.
• Place the product in an upright position.
• Do not switch on if there is no water in the product.
• Do not switch on if there is a possibility that the water in the product is frozen.
• For above ground pool use only. Do not use for spa.
• Do not lift up the product by holding the power cord.
• Have a qualified electrician install a property grounded receptacle outlet, acceptable for outdoor use and protected
from snow and rain, immediately adjacent to the location where the heater will be used.
• Route the supply cord and locate the heater so as to be protected from damage by animals.
• Do not use extension cords.
• Inspect cord before using.
• Unplug heater at receptacle outlet when not in use or before removing from pool.
• Store heater indoors after the end of your swimming season.
• The outlet must not be connected to any tap or fitting other than those specified.
• Keep this product more than 2m away from the pool (For France only).
• Keep the plug of this product more than 3.5m away from the pool.
• The plug shall be accessible after product installed.
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without
supervision
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE,
ELECTRIC SHOCK, ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent some common risks of water
recreation devices and do not cover all instances of risk and danger. Please use common sense and good judgement
when enjoying any water activity.
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 4
PARTS REFERENCE
Before installing your product, please take a few minutes to check the contents
and become familiar with all the parts.
1
2
3
REF. NO. DESCRIPTION QTY. SPARE PART NO.
1
2
2
HOSE
HOSE CLAMP
HOSE SEAL
10116
11489
10134
When ordering parts, be sure to quote the model number and part numbers.
1
2
3
A B
C

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 5
SET UP INSTRUCTIONS
The appliance is ready to work under the following conditions:
FREE CHLORINE (HCIO + CIO- +CI2) up to 3 ppm
pH 6.8 - 8.0
CHLORIDES up to 250 ppm
ISOCYANIC ACID up to 100 ppm
CALCIUM HARDNESS up to 500 ppm
BROMIDE (HBrO) up to 8 ppm
IMPORTANT: The electrical pool heater must be installed as the last piece of pool
equipment before the saltwater pool or chlorine generator system in the water return
line to the pool.
1. Assemble the above-ground-pool (AGP) and its filter pump per installation
instructions.
2. Remove the electrical pool heater and it’s accessories from the packaging.
3. Place the electrical pool heater in line after the filter pump.
4. Connect the hose (1) to the electrical pool heater inlet. (See following page)
5. If your above-ground-pool is filled up with water, unscrew the strainer grids from the
strainer connectors and insert the black hat-like plugs into the strainer connectors
before electrical pool heater installation. Go to step 6 directly if your pool is empty.
6. Disconnect the water return (to the pool) hose from the filter pump connection, and
connect it to the upper electric pool heater connection with a hose clamp.
7. Connect the second hose to the lower electric pool heater connection and to the
lower pump connection. Make sure all the hose clamps (2) are tight.
8. If applicable, return strainer grids to strainer connectors inside pool after removing
black hat-like plugs that prevented water from flowing out of the pool.
9. Connect the electric pool heater to the power outlet. Test RCD as shown on following
page.
10. Turn pump on. Check water is flowing through the heater. Then turn heater on.
IMPORTANT
If the heater is not in an upright position a safety switch will automatically turn
the heater off. Be sure the heater is always in an upright position while the cord
is connected to the power outlet.

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 6
1. Plug RCD into power outlet. Press RESET
button on the RCD plug. Indicator should
be "ON". See FIG. 1.
2. Press T button on the RCD plug. Indicator
should be "OFF". See FIG. 2.
3. Press RESET button for use. Do not use if
test fails. Contact a qualified electrician
to determine cause of failure.
IMPORTANT
Filter pump must be operating before turning on heater.
RESET
T
Fig (1)
RESET
T
Fig (2)
RESET
TEST
WATER
FROM
POOL
WATER
TO
POOL
FILTER PUMP
ELECTRIC POOL
HEATER
SET UP INSTRUCTIONS (continued)
RCD OPERATING INSTRUCTIONS

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 7
OPERATING INSTRUCTIONS
1. Switch the knob clockwise to the "I" position to
turn the electric pool heater on. See FIG. 3.
2. The red indicator light on the heater top will
light up indicating heater is operating.
3. Run the heater to your desired temperature.
4. Switch the knob counter-clockwise to the "0"
position to turn the electric pool heater off.
See FIG. 4.
NOTE: Turn off the heater before turning off
the filter pump or entering the pool.
5. The red indicator light on the heater top will
turn off.
SPECIAL NOTES
• Always use a thermometer to test the pool water temperature before entering or using
the pool. If the thermometer indicated water temperature is over 95 degrees Fahrenheit
(35 degrees Celsius), wait until the indicated water temperature drops below 95degrees
Fahrenheit (35 degrees Celsius) before using the pool, or below 82 degrees Fahrenheit
(28 degrees Celsius) before operating the electric pool heater again.
IMPORTANT
NEVER use the pool if indicated water temperature is more than 95 degrees
Fahrenheit (35 degrees Celsius).
Do not operate electric pool heater while the pool is in use or occupied.
Fig (3)
Fig (4)

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 8
Notices:
• The table above is for reference only. Data were drawn under pool water temperature
77 degrees Fahrenheit (25 degrees Celsius), covered by solar cover during the sunny day.
• The ambient temperatures of air and water have an effect on the water heat up efficiency.
OPERATING TIME TABLE
Pool Type
EASY SET®
POOL
ROUND METAL
FRAME POOL
SMALL
RECTANGULAR
METAL FRAME
POOL
Water Capacity
(
Calculated at 90% for
Frame Pool
and 80% for Easy Set
& Oval Pool)
(Gals) (Liters)
Time to
increase by
1 degree
Celsius
Time to
increase by
1 degree
Fahrenheit
(Hours)
(Hours)
8' x 27" (244cm x 68cm)
577 2184 1.0 1.5
8' x 30" (244cm x 76cm)
10' x 30" (305cm x 76cm)
12' x 30" (366cm x 76cm)
12' x 36" (366cm x 91cm)
12' x 42" (366cm x 107cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
10' x 30" (305cm x 76cm)
12' x 30" (366cm x 76cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
86-5/8" x 59" x 23-5/8" (220cm x 150cm x 60cm)
102-1/2" x 63" x 25-5/8" (260cm x 160cm x 65cm)
118" x 78-3/4" x 29-1/2" (300cm x 200cm x 75cm)
149-5/8" x 78-3/4" x 31-1/2" (380cm x 220cm x 80cm)
177-1/4" x 86-5/8" x 33-1/2" (450cm x 220cm x 85cm)
INTEX ABOVE GROUND POOLS (AGP’s)
639 2420 1.0 1.5
1018 3854 1.0 2.0
1485 5619 1.5 3.0
1779 6732 2.0 4.0
2454 9290 2.5 5.0
2822 10680 3.0 6.0
3284 12431 4.0 7.0
1185 4485 1.5 2.5
1718 6503 2.0 3.5
3282 12422 4.0 7.0
3861 14614 4.5 8.0
4440 16806 5.0 9.0
439 1663 0.5 1.0
603 2284 1.0 1.5
1013 3834 1.0 2.0
1373 5198 1.5 3.0
1907 7217 2.0 4.0

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 9
ELECTRIC POOL HEATER STATIONARY MOUNTING OPTION
Some countries, especially in the European community, require the electric pool heater to
be secured to the ground or to a base in a permanent upright position. Check your local
authorities to determine if there is a regulation in your area regarding above-the-ground
swimming pool electric pool heaters. If yes, then the electric pool heater can be mounted
to a platform using the two holes located in the base. See drawing below.
The electric pool heater can be mounted on a cement base or onto a wooden platform to
prevent accidental falling over. Total assembly must exceed 18kg. The European norm
EN 60335-2-41 requires this product be secured to the ground or to a base.
1. The mounting holes are 6.4 mm in diameter and spaced 156 mm apart.
2. Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
156 mm

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 10
POOL CARE AND CHEMICALS
• All pools require care to keep the water clear and hygienically clean. With proper
chemical control, your filter will help attain this objective. Consult your pool supply
dealer for instructions regarding the proper use of chlorine, algaecide and other
chemical agents required for sparkling clear water.
• Keep pool chemicals away from children.
• Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations
could occur.
• Daily pH checking and chemical treatment of the water is very important and can not
be overemphasized. Chlorine, algaecide and maintenance of proper pH
levels are required when filling the pool as well as during the season. Consult your
local swimming pool supply store for instructions.
• The season's first filling of the pool may have brackish water requiring extra water
additives and extra filter changes. Do not allow swimming in pool until the pH level is
balanced. Consult your local swimming pool supply store for instructions.
• Keep spare filter cartridges on hand. Replace cartridges every two weeks.
• Chlorinated water may damage lawns, gardens or shrubbery as children play in the
pool and splash water outside the pool. Lawn areas underneath the pool liner will be
destroyed. Note that some types of grass may grow through the liner but function
is not affected.
LONG TERM STORAGE
1. Before emptying your pool for long term storage, or relocation, be sure the water is
directed towards an acceptable drain water receptacle away from the house. Check
local regulations for specific directions regarding disposal of swimming pool water.
2. Disconnect power cord from electrical outlet.
3. After pool is emptied of all water, disconnect the electric pool heater from the hoses
reversing the installation instructions.
4. Air-dry the unit before storage.
5. Store the unit and accessories in a dry, temperature controlled, between 32 degrees
Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit (40 degrees Celsius)
storage location.
6. The original packing carton can be used for storage.

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 11
TROUBLESHOOTING GUIDE
• Plug in the power cord.
• Switch the knob clockwise to the "I" position
to turn the electric pool heater on.
• Re-plug the GFCI/RCD and press the
“RESET” button.
• The temperature sensor will cut off the
power of heater when the water temperature
is above approximately 95oF (35°C). It
continues to work when the water
temperature drop below approximately 82°F
(28°C).
• Turn on the filter pump.
• Ensure the plunger valves are opened (if
any).
• Ensure your filter cartridges are clear from
debris and dirt.
• Release all trapped air in the circulation line.
• Check for the direction of water inlet and
water outlet hose. Reverse the hose if
necessary.
• Always use the solar cover if the pool is not
occupied.
• Increase the heating time properly.
• Stop the heater and shorten the heating time.
• Tighten/reinstall hose clamps.
• Reposition/replace hose seals.
• Unplug the GFCI/RCD and then re-plug in
and press the “RESET” button to start the
heater. Contact Intex Service Center if it trips
off continuously.
THE RED INDICATOR
DOES NOT LIGHT UP
DURING USE
THE WATER
TEMPERATURE
DOES NOT INCREASE
ALTHOUGH THE RED
INDICATOR IS LIT UP
THE WATER
TEMPERATURE IS TOO
HIGH
HOSE LEAKING
GFCI/RCD KEEPS
TRIPPING OFF
1. The power cord is not plugged in.
2. The knob is not fully switched to on
position – “I”.
3. The GFCI/RCD plug is not turned
on.
4. The water temperature is too high.
5. No water flow.
6. Low water flow.
1. Pool or solar cover not been used.
2. The pool size or water capacity
exceeds the heater capacity.
3. The water temperature is too low.
1. Heating time too long.
1. Hose clamps.
2. Hose seals.
1. Product failure or electrical circuit
problem.
PROBLEM CAUSE REMEDY
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 12
COMMON POOL PROBLEMS
PROBLEM DESCRIPTION CAUSE REMEDY
ALGAE
COLORED WATER
SUSPENDED
MATTER IN
WATER
CHRONIC LOW
WATER LEVEL
SEDIMENT ON
POOL BOTTOM
SURFACE DEBRIS
• Chlorine and pH levels
need adjustment.
• Copper, iron or maganese
in water being oxidized by
the added chlorine.
Common.
• "Hard water" caused by
pH level being too high.
• Chlorine content is low.
• Foreign matter in water.
• Rip or hole in pool liner or
hoses. Tighten caps.
• Heavy use, getting in and
out of pool.
• Pool too close to trees.
• Super chlorinate with shock
treatment. Correct pH to your
pool store's recommended level.
• Vacuum pool bottom.
• Maintain proper chlorine level.
• Adjust pH to recommended level.
• Run filter until water is clear.
• Clean cartridge frequently.
• Correct pH. Check with pool
dealer for water treatment.
• Check for proper chlorine level.
• Clean or replace your filter.
• Repair with patch kit.
• Finger tighten all caps.
• Use Intex pool vacuum to clean
bottom of pool.
• Use Intex pool skimmer.
• Greenish water.
• Green or black spots
on pool liner.
• Pool liner is slippery
and/or has a bad odor.
• Water turns blue,
brown, or black when
first treated with
chlorine.
• Water is cloudy or
milky.
• Level is lower than on
previous day.
• Dirt or sand on pool
floor.
• Leaves, insects etc.
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves inherent risks of
injury and death. To reduce your risk of injury, read and follow all product, package and
package insert warnings and instructions. Remember, however, that product warnings,
instructions and safety guidelines cover some common risks of water recreation, but do
not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following general guidelines
as well as guidelines provided by nationally recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as a “lifeguard” or
water watcher, especially when children are in and around the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool hazards and about the
use of protective devices such as locked doors, barriers, etc.
• Instruct all pool users, including children what to do in case of an emergency.
• Always use common sense and good judgement when enjoying any water activity.
• Supervise, supervise, supervise.

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
Page 13
PARTS LIST
Your Electric Pool Heater has been manufactured using the highest quality materials and workmanship. All Intex
products have been inspected and found free of defects prior to leaving the factory. This limited warranty applies
only to the Electric Pool Heater and accessories listed below.
This limited warranty is in addition to, and not a substitute for, your legal rights and remedies. To the extent that
this warranty is inconsistent with any of your legal rights, they take priority. For example, consumer laws across
the European Union provide statutory warranty rights in addition to the coverage you receive from this limited
warranty: for information on EU-wide consumer laws, please visit the European Consumer Center website at
http://ec.europa.eu/consumers/ecc/contact_en/htm.
The provisions of this limited warranty apply only to the original purchaser and is not transferable. This limited
warranty is valid for the period noted below from the date of the initial retail purchase. Keep your original sales
receipt with this document, as proof of purchase will be required and must accompany warranty claims or the
limited warranty will be invalid.
Electric Pool Heater Warranty – 1 Year
Hoses Warranty – 180 days
If you find a manufacturing defect in the Electric Pool Heater during the warranty periods noted above, please
contact the appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet. If the item
is returned as directed by the Intex Service Center, the Service Center will inspect the item and determine the
validity of the claim. If the item is covered by the provisions of the warranty, the item will be repaired or replaced,
with the same or comparable item (at Intex’s choice) at no charge to you.
Other than this warranty, and other legal rights in your country, no further warranties are implied. To the extent
possibly in your country, in no event shall Intex be liable to you or any third party for direct or consequential
damages arising out of the use of your Electric Pool Heater, or Intex or its agents’ and employees’ actions
(including the manufacture of the product). If your country does not allow the exclusion or limitation of incidental
or consequential damages, this limitation or exclusion does not apply to you.
You should note that this limited warranty does not apply in the following circumstances:
• If the Electric Pool Heater is subject to negligence, abnormal use or application, accident, improper operation,
improper voltage or current contrary to operating instructions, improper maintenance or storage;
• If the Electric Pool Heater is subject to damage by circumstances beyond Intex’s control, including but not
limited to, ordinary wear and tear and damage caused by exposure to fire, flood, freezing, rain, or other
external environmental forces;
• To parts and components not sold by Intex; and/or
• To unauthorized alterations, repairs or disassembly to the Electric Pool Heater by anyone other than Intex
Service Center personnel.
The costs associated with the loss of pool water, chemicals or water damage are not covered by this warranty.
Injury or damage to any property or person is not covered by this warranty.
Read the owner’s manual carefully and follow all instructions regarding proper operation and maintenance of your
Electric Pool Heater. Always inspect your product prior to use. This limited warranty will be void if use instructions
are not followed.
LIMITED WARRANTY

(114BS) ELECTRIC POOL HEATER ENGLISH 7.5” X 10.3” PANTONE 295U 08/16/2015
English
114
BS
SAVE THESE INSTRUCTIONS
English
INTEX
®
©2015 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex
Trading Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos
reservados/Alle Rechte vorbehalten. Printed in China/Imprimé
en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license
from/®™ Marques utilisées dans certains pays sous licence de/
Marcas registradas utilizadas en algunos países del mundo bajo
licencia de/Warenzeichen verwendet in einigen Ländern der Welt
in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd.,
Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong &
Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801
• Distributed in the European Union by/Distribué dans l’Union
Européenne par/Distribuido en la unión Europea por/Vertrieb in der
Europäischen Union durch/Intex Trading B.V., Roosendaal – The
Netherlands
www.intexcorp.com
Don’t forget to try these other fine Intex products:
Pools, Pool Accessories, Inflatable Pools and In-Home
Toys, Airbeds and Boats available at fine retailers or
visit our website.
Table of contents
Other Intex Marketing Swimming Pool Heater manuals
Popular Swimming Pool Heater manuals by other brands

Laars
Laars PNCP Installation and operation instructions

Hayward
Hayward HP55TR Installation instructions manual

Nibe
Nibe POOL 310 Installer manual

Hayward
Hayward H100ID1 Operation manual

Laars
Laars DP2000 Installation, operation and service manual

Elecro Engineering
Elecro Engineering 800 Series Installation instructions & operating manual

Raypak
Raypak Versa 105B Brass Installation and operating instructions

Hayward
Hayward H-Series manual

Sungrabber
Sungrabber AGP Installation and operation manual

Vornado
Vornado Sunny Owner's handbook

fluidra
fluidra Astral Pool IHPt127 Installation instructions manual

Aquacal
Aquacal AeroTemp 155 Brochure & specs