Intex CLW090 User manual

(335IO) LED WATERFALL ENGLISH SIZE: 4.875” X 7.25” 08/08/2017
English 335
IO
SAVE THESE INSTRUCTIONS
Page 1
General
• No tools are required for the assembly.
• Fits all round and rectangular Metal Frame, Prism and Ultra Frame pools (not
suitable for Easy Set, Oval and Panel pools).
• Built-in hydroelectric generator powers the LED light, no batteries or electrical
connection required.
• Lights in 3 colors: green, blue and red. Preset 5 seconds between colors
change. Best seen at night or under low light condition.
• Pump flow rate required: 4,542 - 12,113 L/h (1,200 - 3,200 g/h). System flow
rate required: 3,596 - 9,274 L/h (950 - 2,450 g/h).
• Make sure the pump and the pool are setup, and the pool is filled with water
just below the water return inlet connection.
• Remove the waterfall before placing a pool cover over the pool.
• Store the product indoors when not in use.
• For pool and filter pump problems refer to their respective owner’s manual.
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
INTEX®OWNER'S MANUAL
MULTI-COLOR LED WATERFALL CASCADE
Model CLW090
• Assembly and disassembly by adults only.
• This is not a toy. Do not allow children to play with this product.
• Never grab, pull, push, lean on or obstruct the waterfall at any time.
• Ensure all the clamp screws, adaptor and hose are securely attached.
• This product is intended to be used only for the purposes described in the
manual.
FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID PROPERTY
DAMAGE OR OTHER INJURY.
WARNING
335-*IO-R0-1808
©2017 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten.
Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas
registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex
Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box
1440, Long Beach, CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/
Vertrieb in der Europäischen Union durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com

(335IO) LED WATERFALL ENGLISH SIZE: 4.875” X 7.25” 08/08/2017
English 335
IO
SAVE THESE INSTRUCTIONS
Page 2
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not
to scale.
PARTS LIST
REF. NO. DESCRIPTION QTY. SPARE PART NO.
1Waterfall set 1 12556
2Clamp screw 2 12560
3Clamp nut 2 12561
4Fixer 2 12565
5Bypass valve 1 12569
6L-shape O-ring 3 11228
7Adaptor B 1 11070
8Connecting hose 1 11535
Due to a policy of continuous product improvement, Intex reserves the right to
change specifications and appearance, which may result in updates to the
instruction manual without notice.
Setup
1. Locate the pool water return inlet connection or plunger valve.
2. To maximize the performance of the waterfall, place the waterfall to the left
side and within reach of the water return inlet connection or plunger valve, as
there is less twisting of the bypass connecting hose (8).
3. Place the waterfall clamp over the frame pool horizontal top beam. Make sure
it is on the left side and within reach of the water return inlet connection or
plunger valve. Securely tighten the clamp screws by hand. See fig 1 - 3.
7
6
6
1
2
3
4
5
8

(335IO) LED WATERFALL ENGLISH SIZE: 4.875” X 7.25” 08/08/2017
English 335
IO
SAVE THESE INSTRUCTIONS
Page 3
4. For pools with plunger valve and 38mm (1.5 in) hose:
a. Close the water outlet plunger valve.
b. Make sure the pump is off and disconnect the pump return hose from the
pool inlet plunger valve.
c. Remove the pool inlet plunger valve from the inlet threaded connector.
This plunger valve will not be needed, store in a safe place.
d. Attached the bypass valve (5) to the pool inlet threaded connector and
tighten the collar nut by hand.
e. Reconnect the pump return hose to the bypass valve (5) lower port. See
fig 4.
FIG (1) FIG (2) FIG (3)
1
2
12
FIG (4)
Pool
Waterfall
Pump
8
5

(335IO) LED WATERFALL ENGLISH SIZE: 4.875” X 7.25” 08/08/2017
English 335
IO
SAVE THESE INSTRUCTIONS
Page 4
5. For pools with 32mm (1.25 in) hose connections:
a. From the inside of the pool, insert the strainer hole plug into the water
outlet fitting.
b. Make sure the pump is off and disconnect the pump return hose from the
pool inlet fitting.
c. Attach the adaptor B (7) to the pool inlet fitting and securely tighten the
clamp by hand.
d. Attach the bypass valve (5) to the adaptor B (7) and tighten the collar nut
by hand.
e. Reconnect the pump return hose to the bypass valve (5) lower port. See
fig 5.
6. Attach the connecting hose (8) between the waterfall (1) and the bypass valve
(5) left side port. See fig 4 - 5.
FIG (5)
Pool
Waterfall
Pump
8
57
7. Bypass valve (5) handle setting:
a. Pool position (handle pointing down): water flow from pump to pool. See
fig 6.
b. Waterfall position (handle pointing up): water flow from pump to waterfall.
See fig 7.
c. Never set the bypass valve handle between pool and waterfall position
(handle pointing left or right side), as this will affect the performance of the
waterfall and the pump. See fig 8.

(335IO) LED WATERFALL ENGLISH SIZE: 4.875” X 7.25” 08/08/2017
English 335
IO
SAVE THESE INSTRUCTIONS
Page 5
8. Resume filling the pool with water to the recommended level.
9. Open the water outlet plunger valve or remove the strainer hole plug from the
outlet fitting.
10. Turn on the pump and purge all the air out from the hoses and pump.
Maintenance and Long Term Storage
1. Regularly check all components for sign of damage, straining. Discard and
replace damaged components immediately.
2. Use a sponge and clean water to wipe away any soil or stains.
3. Disassemble the product when the temperature drops below 5°C (41°F) by
reversing the above setup instructions, drain the water out of the waterfall, and
make sure all components are completely dry before storage.
4. Store the waterfall and accessories in a dry, temperature controlled, between
0º – 40ºC (32º – 104ºF), storage location.
5. The original packing can be used for storage.
TROUBLE SOLUTION
Light is off /
flashing • Make sure the filter pump is operating, the pump water
return hose is attached to the bypass valve lower port and
the bypass valve is in the waterfall position (handle pointing
up). see “Setup” section.
• Make sure the connecting hose (8) is attached between the
waterfall and the bypass valve left port.
• Check if the pump system flow rate is within the specified
range, if the system flow rate is less than 3,596 L/h (950 g/h),
change pump with higher system flow rate.
• Clean or replace the filter pump cartridge. If using a sand
filter, ensure the sand media is clean by backwashing it.
• Use a garden hose to wash the waterfall opening, check to
see if any sand or deposits inside the waterfall set.
• Contact Intex Service Center.
Poor water
cascade
performance
• Use a damp cloth to wipe away any dirt on the waterfall
opening.
• The performance depends on the filter pump flow rate. If
you are not satisfied with the water cascade performance,
a higher flow rate filter pump is recommended.
FIG (6) FIG (7) FIG (8)

(335IO) LED WATERFALL ENGLISH SIZE: 4.875” X 7.25” 08/08/2017
English 335
IO
SAVE THESE INSTRUCTIONS
Page 6
Limited Warranty
Your Waterfall has been manufactured using the highest quality materials and workmanship.
All Intex products have been inspected and found free of defects prior to leaving the factory.
This Limited Warranty applies to the Waterfall only.
This limited warranty is in addition to, and not a substitute for, your legal rights and remedies.
To the extent that this warranty is inconsistent with any of your legal rights, they take priority.
For example, consumer laws across the European Union provide statutory warranty rights in
addition to the coverage you receive from this limited warranty: for information on EU-wide
consumer laws, please visit the European Consumer Center website at http://ec.europa.eu/
consumers/ecc/contact_en/htm.
The provisions of this Limited Warranty apply only to the original purchaser and are not
transferable. This limited warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this document, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty will
be invalid.
Waterfall Set Warranty – 1 Year
Hoses & Fittings Warranty – 180 days
If you find a manufacturing defect in the Waterfall during the warranty periods noted above,
please contact the appropriate Intex Service Center listed in the separate “Authorized
Service Centers” sheet. If the item is returned as directed by the Intex Service Center, the
Service Center will inspect the item and determine the validity of the claim. If the item is
covered by the provisions of the warranty, the item will be repaired or replaced, with the
same or comparable item (at Intex’s choice) at no charge to you.
Other than this warranty, and other legal rights in your country, no further warranties are
implied. To the extent possibly in your country, in no event shall Intex be liable to you or any
third party for direct or consequential damages arising out of the use of your Waterfall, or
Intex or its agents’ and employees’ actions (including the manufacture of the product). If your
country does not allow the exclusion or limitation of incidental or consequential damages,
this limitation or exclusion does not apply to you.
You should note that this limited warranty does not apply in the following circumstances:
• If the Waterfall is subject to negligence, abnormal use or application, accident, improper
operation, improper voltage or current contrary to operating instructions, improper
maintenance or storage;
• If the Waterfall is subject to damage by circumstances beyond Intex’s control, including
but not limited to, ordinary wear and tear and damage caused by exposure to fire flood,
freezing, rain, or other external environmental forces;
• To parts and components not sold by Intex; and/or.
• To unauthorized alterations, repairs or disassembly to the Waterfall by anyone other than
Intex Service Center personnel.
Injury or damage to any property or person is not covered by this warranty.
Read the owner’s manual carefully and follow all instructions regarding proper operation
and maintenance of your Waterfall. Always inspect your product prior to use. This limited
warranty will be void if use instructions are not followed.