Inverto Unicable II User manual

1
Installation manual
Unicable™II Multiswitch
Programmable/cascadable multiswitch with 32 User Bands,
4 Universal/Wideband Satellite inputs & 1 Terrestrial input
IDLU-UWT110-CUO1O-32P
Item: 5294
Unicable II Programmable/cascadable
multiswitch with 32UB, 4 Universal/
Wideband Satellite inputs & 1 Terrestrial input
IDLU-UWT110-CUO1O-32P
Item: 5294
Satellite - Loop-through output
Terrestrial loop
through output
Terrestrial
input
Made in China
Designed in LU
Satellite - Input
For default UB settings:
www.inverto.tv/dCSS-UB
V/L V/H H/L H/H
Universal Quattro LNB (SAT A/B/C/D) 2 x Wideband LNBs (SAT A/B or C/D)
DC in/Power Inserter in
HorizontalVertical HorizontalVertical
V/L V/H H/L H/H
Satellite B or D
HorizontalVertical
Satellite A or C
HorizontalVertical
Satellite inputs:
- Universal Quattro LNB: 950 - 2150MHz
- 2x Wideband LNBs: 300 - 2350MHz
Terrestrial input: 47 - 862MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Default setup
Programmable setup
Satellite A
CSatellite
B
D
Universal Out
(+Terr) (+Terr)

2

3
Thank you for purchasing Inverto’s advanced Unicable II multiswitch and we are certain it will
meet your expectations. Before installing and operating the product, please read the following
instructions and recommendations. We suggest that you keep this manual for future use.
Warranty
This Unicable II multiswitch is designed for the distribution of satellite and terrestrial television
and radio signals in home installations. The warranty does not apply for products used for other
purposes than those specified herein. The user/installer shall be responsible for any damage in-
curred as a result of not using the product according to the instructions in this manual.
Installation location
The product shall be installed on a wall or other hard inflammable surface. The product shall be
in no case held only with the connected cables. Place the product in a dry environment where
it is not exposed to rain or running water. Do not install the product close to heat sources or in
places exposed to direct sunlight.
Product installation
The following diagram may assist you when drilling the holes:
To connect the product inputs and outputs use high-quality coax-
ial cables designed for satellite reception and F-connectors. Use a
highly shielded coaxial cables with minimum shielding of 90dB. If
you use wall sockets to loopthrough the Unicable II output, make
sure the wall sockets were designed for satellite reception com-
patible with Unicable technology and allows bidirectional signal
propagation. The multiswitch can be powered over any of its out-
put ports by any of the connected STBs if it is able to supply the
necessary power to the switch and the Quattro/Wideband LNB
connected to it. If none of the connected STBs can supply suffi-
cient power, the multiswitch shall be powered by the supplied AC/
DC adapter and Power Inserter over its Unicable II port.
Default product configuration
The satellite input ports of the Multiswitch are configured to support a universal Quattro LNB by
default.
The default configuration of the output ports is as marked on the device’s label. By default - (i)
the Unicable II port operates in dynamic mode (compatible with EN50494/EN50607) and sup-
ports up to 32 User Bands. This allows to connect up to 32 receiver tuners - each to be assigned
to one of the supported 32 User Bands. The list of the User Bands’ parameters appears on the
next page. (ii) upon power-on, the Universal port functions as a standard universal port allowing
to connect a legacy receiver that is not supporting the Unicable/Unicable II (EN50494/EN50607)
protocols, however it switches to operate in a Unicable II mode as soon as it receives a EN50494
or EN50607 DiSEqC command and the 32 User Bands will be shared over the two output ports
(“shared User Bands” mode) and where each UB is only available at the output port through
which it was activated.
Note: The default configuration of the product, can be updated using Inverto’s Programmer de-
vice (not supplied with the product and sold as a separate accessory) and PC Windows software
that can be downloaded from www.inverto.tv.
Unicable II Programmable/cascadable
multiswitch with 32UB, 4 Universal/
Wideband Satellite inputs & 1 Terrestrial input
IDLU-UWT110-CUO1O-32P
Item: 5294
Satellite - Loop-through output
Terrestrial loop
through output
Terrestrial
input
Made in China
Designed in LU
Satellite - Input
For default UB settings:
www.inverto.tv/dCSS-UB
V/L V/H H/L H/H
Universal Quattro LNB (SATA/B/C/D) 2 x Wideband LNBs (SATA/B or C/D)
DC in/Power Inserter in
HorizontalVertical
110.50
113.50
HorizontalVertical
V/L V/H H/L H/H
Satellite B or D
HorizontalVertical
Satellite A or C
HorizontalVertical
Satellite inputs:
- Universal Quattro LNB: 950 - 2150MHz
- 2x Wideband LNBs: 300 - 2350MHz
Terrestrial input: 47 - 862MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Default setup
Programmable setup
Satellite A
CSatellite
B
D
Universal Out
(+Terr) (+Terr)
20.80

4
Note: For optimal performances, the loop through outputs that are not used shall be terminated
with 75ohm DC-decoupled terminating resistors.
The following diagram describes a single satellite reception installation based on the default
configuration of the product:

5
Connect the cables from the Quattro LNB to the input connectors marked with LNB V/L, V/H, H/L
and H/H inputs (pay attention to identification of the Quattro LNB connectors). The multiswitch is
equipped with Terrestrial input. Connect the Terrestrial antenna to this input:
Unicable II Programmable/cascadable
multiswitch with 32UB, 4 Universal/
Wideband Satellite inputs & 1 Terrestrial input
IDLU-UWT110-CUO1O-32P
Item: 5294
Satellite - Loop-through output
Terrestrial loop
through output
Terrestrial
input
Made in China
Designed in LU
Satellite - Input
For default UB settings:
www.inverto.tv/dCSS-UB
V/L V/H H/L H/H
Universal Quattro LNB (SAT A/B/C/D) 2 x Wideband LNBs (SAT A/B or C/D)
DC in/Power Inserter in
HorizontalVertical HorizontalVertical
V/L V/H H/L H/H
Satellite B or D
HorizontalVertical
Satellite A or C
HorizontalVertical
Satellite inputs:
- Universal Quattro LNB: 950 - 2150MHz
- 2x Wideband LNBs: 300 - 2350MHz
Terrestrial input: 47 - 862MHz
Satellite Loop-Through loss: 3dB
Terrestrial Loop-Through loss: 3dB
Default setup
Programmable setup
Satellite A
CSatellite
B
D
Universal Out
(+Terr) (+Terr)
The default frequencies, supported protocols and PINs of the User Bands are listed below (default
UB bandwidth = 30MHz):
CH17: 1530MHz (EN50607, PIN=235)
CH18: 1566MHz (EN50607, PIN=97)
CH19: 1602MHz (EN50607, PIN=101)
CH20: 1638MHz (EN50607, PIN=198)
CH21: 1716MHz (EN50607, PIN=223)
CH22: 1752MHz (EN50607, PIN=7)
CH23: 1788MHz (EN50607, PIN=39)
CH24: 1824MHz (EN50607, PIN=43)
CH25: 1860MHz (EN50607, PIN=209)
CH26: 1896MHz (EN50607, PIN=38)
CH27: 1932MHz (EN50607, PIN=133)
CH28: 1968MHz (EN50607, PIN=57)
CH29: 2004MHz (EN50607, PIN=182)
CH30: 2076MHz (EN50607, PIN=189)
CH31: 2112MHz (EN50607, PIN=213)
CH32: 2148MHz (EN50607, PIN=67)
CH1: 1210MHz (EN50494+EN50607, PIN=37)
CH2: 1420MHz (EN50494+EN50607, PIN=18)
CH3: 1680MHz (EN50494+EN50607, PIN=251)
CH4: 2040MHz (EN50494+EN50607, PIN=131)
CH5: 984MHz (EN50494+EN50607, PIN=48)
CH6: 1020MHz (EN50494+EN50607, PIN=23)
CH7: 1056MHz (EN50494+EN50607, PIN=88)
CH8: 1092MHz (EN50494+EN50607, PIN=204)
CH9: 1128MHz (EN50607, PIN=194)
CH10: 1164MHz (EN50607, PIN=89)
CH11: 1256MHz (EN50607, PIN=157)
CH12: 1292MHz (EN50607, PIN=136)
CH13: 1328MHz (EN50607, PIN=13)
CH14: 1364MHz (EN50607, PIN=91)
CH15: 1458MHz (EN50607, PIN=23)
CH16: 1494MHz (EN50607, PIN=179)

6
Programmable configurations using Inverto’s
programmer and PC software
The following diagrams describe installation receiving two and four satellites using satellites over
two wideband LNBs:

7
Connect the cables from the Wideband LNBs to the input connectors marked with Sat A/C
Vertical and Horizontal and Sat B/D Vertical and Horizontal (pay attention to identification of the
Wideband LNB connectors).
Note: The four satellite installation requires the output ports of the two Multiswitch units to be
connected to an external combiner as shown in the diagram (to provide for DiSEqC 2.0 com-
munication, the combiner should support bidirectional pass through for DC and 22kHz signals).

8
The following diagram describes reception of a single satellite feed by up to 16 Unicable
(EN50494) receivers:
For optimized performance, please follow the recommendations below:
1. Use the highest frequency for a wall socket located the nearest to the multiswitch and use
the lowest frequency for wall socket located farest to the multiswitch.
2. If you install less than 32 receiver tuners, use the lowest frequencies first. We also recom-
mend to keep record of the user bands allocated to the different connections as these user
bands will then have to be set in the receiver. The satellite receivers connected to the Uni-
cable II output should be Unicable compatible (ie EN50494 and/or EN50607 compatible).
Note: For optimal performances, the loopthrough outputs that are not used shall be terminated
with 75ohm DC de-coupled terminating resistors.

9
Technical parameters
Inputs 4 x IF inputs:
- From 1x Quattro LNB (default)
- From 2x Wideband LNBs
1 x UHF/VHF input from Terrestrial antenna
Outputs 4 x Loopthrough satellite IF outputs
1 x Loopthrough terrestrial output
1 x Unicable II (dCSS/EN50607) output, dynamic mode
by default, supporting up to 32 UBs. With combined
terrestrial signal.
1 x Universal (Legacy) by default upon power up, auto
switch to Unicable II upon receiving EN50494/
EN50607 command. With combined terrestrial signal
Frequency range Satellite:
- Quattro LNB: 950-2150MHz (default)
- Wideband LNB: 300-2350MHz
Terrestrial: 47-862MHz
Loopthrough loss Satellite: max 4dB
Terrestrial: max 4dB
Gain (without AGC) Satellite: Unicable II (dCSS): min. 25dB
Legacy (Universal): min. 10dB
Terrestrial: no amplification, typ. -15dB
Input power level -50dBm ~ -15dBm
Output power level (AGC controlled) -25dBm (default)
Isolation Satellite-Satellite outputs: min 25dB
Satellite-Terrestrial : min 25dB
Control protocol DiSEqC™ commands extension according to CENELEC
EN50494 and/or EN50607
Power consumption 500mA max. @13VDC
Dimensions (W x H x D mm) W=110.50 H=113.50 D=20.80 mm
Temperature range -20C - +60C
AC/DC adaptor Input voltage: 100-240VAC, 50/60Hz
Output voltage: 19VDC
Output current: 940mA
Short circuit protection: Yes

10
Safety
Never open a powered product. This may result in electrical hazard.
Never work on the product, TV set or other powered devices during or before a storm. A light-
ning strike into the antenna may cause dangerous overvoltage over the product’s metallic/con-
ductive parts.
Make sure the local electricity network corresponds to the operating voltage of the AC/DC adap-
tor.If the products gets into contact with liquid it must be disconnected from the main power.
It is recommended to disconnect the product from the main power if it is not used for long pe-
riods of time.
When disconnecting the product don’t pull the cable but the plug to prevent damage of the
cable (wobbly plugs and outlets result in fire risk).
The product shall be serviced by qualified experts only.
Troubleshooting
Make sure the satellite antenna and LNB are properly fixed, connected and adjusted and that the
satellite receivers are installed, connected and switched on according to available instructions.
Ensure there is no short circuit on the product inputs. This will prevent power to the LNB. If this is
the case, disconnect the product from the main power, and then find and remove the short cir-
cuit on the product inputs. Then re-connect the multiswitch to the main power. Frequent defects
are in connector joints i.e. if the central conductor is too short and fails to make contact in the
connector. Also the shielding braid should make proper contact with the connector coat. Some-
times a reset to the multiswitch microprocessor is sufficient to remove a fault: simply disconnect
the multiswitch from main power for 30 seconds and then reconnect again. If you are unable to
remove the fault yourself, please contact your distributor.
Disposal
Following relevant EU directives, this device shall not be disposed of together with municipal
waste. Use local waste collection and recycling systems to dispose wore out products.
*DiSEqC™ is a registered trademark of Eutelsat
*For purpose of brevity, some product descriptions in this sheet remain at platform level and may not be referred to
as detailed data-sheets of the products. Inverto Digital Labs reserves the right to amend, omit or add products,
product-lines, and/ or features without notice.

V250116
FTA Communication Technologies S.a r.l.
18 Duchscherstrooss, L-6868 Wecker, Luxembourg
Tel: [phone], Fax: [phone]
[email protected] www.inverto.tv