3
Step 3b - Brick & Concrete Installation
1. For mounting to concrete or brick walls, please mark the wall carefully and drill using a 10mm masonry drill
to the length of the screw, a depth of 80mm - see diagram ‘F’.
2. Fully insert the plastic plugs into the solid wall (pushed beyond any plaster) closely following step 3c and
diagram ‘H’.
3. Hold your wall mount in position and insert the supplied screws and washers, check the wall mount is level
and fully tighten into the concrete or brick using a 12mm socket and ratchet or spanner or parts ‘C/G’ socket
wrench. Please ensure they fit securely before tightening the screws into the plastic plugs. Replace wall plate
cover caps once the wall mount is secure - see diagram ‘G’.
Diagram ‘F’ Diagram ‘G’
Step 3c - Please Note
Many modern houses have an air-gap behind plasterboard or drywall. Our fixings are only designed to work
with the plastic plug fully inserted into the brick or concrete that lies behind any plaster or drywall air gap. To
use our fixings in this way YOU MUST insert the plug past any plaster/drywall and fully into the underlying
brick or concrete to gain a secure fixing (the drill depth may have to be increased to make sure the plug can
be fully inserted into the brick or concrete).
When fitting, the screw must be at least 3/4 of the way into the plug, and the plug must be fully inserted into
brick or concrete to be effective.
Depending on the plasterboard/drywall air gap you may need to purchase longer fixings to ensure a secure
fix (plasterboard wall fixings are NOT supplied). Diagram ‘H’
Step 4 - Mounting your TV/Monitor
1. Check TV/monitor VESA by measuring the distance between the mounting holes on the back of the screen
- this is where bolts A/B will fit.
2. Screw 2 bolts into the top two holes on the back of the TV/monitor using bolts A/B and tighten in 3 turns
leaving room between the bolt head and rear of screen for hanging (see diagram ‘I’).
3. Carefully lift TV/monitor and hang onto the TV/monitor arms VESA plate (see diagram ‘J’).
4. Fit the bottom 2 bolts into the VESA plate and tighten all the bolts (see diagram ‘K’).
Please Note: Set the torque of the arm if the screen moves down too easily (see Step 5).
Diagram ‘I’ Diagram ‘J’ Diagram ‘K’
4
Step 5 - Using Your Invision MX250 Ergonomic TV/Monitor Wall Mount
Setting the dynamic elevation torque
1. Once fitted you need to adjust the tension of the wall
mount arm. Apply downwards pressure to the arm to
gain access to the torque screw - see diagram ‘L’.
Adjust the tension until the screen stays at the desired
height using the steps below.
2. If the screen moves upwards of its own accord then
adjust the torque using the 5mm Allen key ‘G’ and wind
the set screw in the minus direction (clockwise).
3. If the screen moves downwards of its own accord then
adjust the torque using the 5mm Allen key ‘G’ and wind
the set screw in the plus direction (anti-clockwise).
Diagram ‘L’
Step 6 - Cable Management
Please leave adequate slack while routing cables
1. Remove the retention pin from the middle cable
management clip - pinch the clip to remove it from its
holder and set to one side - see diagram ‘M’.
2. Route all cables through the bottom cable management
clip located on the wall plate.
3. Route one cable at a time through the top cable
management clip leaving slack to connect cables to
TV/Monitor (bend the clip down to slide the cables in or
remove the screw and replace once cables are fitted).
4. Finally add your cables to the middle cable management
clip and replace it back in its holder. Add the retention pin
to fully secure it in place.
Diagram ‘M’
1.
2.
3.
4.
Step 7 - Adjusting the Tilt Angle
The tilt can be set to your desired viewing
angle by simply moving the screen backwards
and forwards by hand. If you find the screen moves
forward off its own accord, if necessary the tilt
adjustment can be tightened using Allen
key ‘G’ - see diagram ‘N’.
Diagram ‘N’
G
Step 8 - Rotational Features
1. Your TV/Monitor wall mount allows you to rotate your
screen through 360 degrees to view in portrait mode or
landscape mode providing the VESA mount on your
screen is central - see diagram ‘O’
Please Note:
Beware of trapping or damaging cables when rotating
TV/Monitor. DO NOT ROTATE MORE THAN 90
DEGREES IN EACH DIRECTION.
Diagram ‘O’
Troubleshooting:
Don’t panic! In case of any issues with compatibility or for any advice on fitting, please contact our team at
help@InvisionTechnology.co.uk and we will help you overcome any problems. All our products carry our
Compatibility Promise. Your installation is now complete - Sit back & enjoy!
To activate your 3 year warranty please email your name, order number
and product ref MX250 to warranty@InvisionTechnology.co.uk
