inVue CT100 User manual

CT100
Premium Tablet Stand

2 3
5
10
20
30
Overview
Important! Read entire instruction guide before starting
installation.
System Components
1. Tablet Stand (CT100)
2. Shroud
3. Power Connector
4. OEM Power Supply
5. IR Key (AF4400 or PK4400) – To unlock shroud from
stand
System Overview:
The Premium Commercial Tablet Stand and Shroud are
used to secure your tablet.
TT15 Bit
Drill Hole Saw
19 mm (0.75”)
Shroud
Tablet Stand
CT100
OEM Power Supply
Key
AF4400 or PK4400
Power Connector
TOOLS

4 5
Drill a 19 mm (0.75”) hole in display counter. Wipe
display counter with alcohol wipe provided. Let it dry
completely.
1
5
10
20
30
CONTENTS: One pad saturated in 75%
Isopropyl Alcohol
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
CONTENTS: One pad saturated in 75%
Isopropyl Alcohol
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
2Plug power connector into merchandise.

6 7
3 4 Remove tab to activate battery. Remove both adhesive
films on stand and slide cord and stand threaded post
through hole. Press firmly for at least 10 seconds.
Slide tablet into bottom shroud. Slide top of shroud to
merchandise. Tighten both screws with TT15 bit.

8 9
5 6
Slide security washer and metal washer onto stand
below counter. Slide stand cord in opening of washer.
Loosely tighten washer.
Snap shroud onto stand. You should hear a “beep.”
Confirm shroud is fully engaged on all sides and is
locked on stand by pulling on shroud.

10 11
7 8
Confirm shroud is aligned correctly and straight with
front of display counter. Fully tighten washer.
Plug power supply to OEM and plug into outlet.

12 13
9Removing Shroud
Place IR key onto IR lens on stand. Press button on IR key to
release shroud from stand. Stand will re-lock automatically
after 5 seconds.
Rotate shroud 90 degrees to display in landscape.

14 15
Removing Merchandise
Remove both screws with TT15 bit. Lift up on handle to slide
shroud off and remove merchandise.
Frequently Asked Questions & Tips
Q My merchandise is not powering up.
A 1) Conrm correct power connector is being used for mer-
chandise model. 2) Conrm power connector is completely
plugged into merchandise (page 2). 3) Conrm power supply
is plugged into stand cord and outlet (page 11).
Q Lock is not engaging.
A 1) Conrm power supply is plugged into stand cord and
outlet (page 11).
Q My stand is loose or not stable.
A Conrm clear lm on adhesive has been removed (page 7)
and wingnut below counter is fully tightened (page 10).
T Once IR Key is used to remove shroud from stand, you have
10 seconds before stand re-locks (page 13).
T Conrm all sides of shroud are fully engaged with stand
(page 9).
T Conrm correct power connector and shroud are being
used for merchandise model.

© 2014 InVue Security Products Inc. All rights reserved.
InVue is a registered trademark of InVue Security Products.
SD0190 Rev1 02/24/14
www.invuesecurity.com
Corporate Office (North America) // 704.752.6513 •888.55.INVUE
Europe, Middle East & Africa // +31.23.8900150
Asia Pacific // +852.3127.6811
Latin America // +52.55.90003957