IOGear M1063 User manual

1
GUW2015V
PART NO. M1063
Installation
Installation Guide
Wireless USB to VGA Adapter

2
3

2
3
Table of Contents
System Requirements 4
Important Information 5
Package Contents 6
Device Overview 7
Wireless USB VGA Software Installation 9
Cable Association with the Wireless USB
Enabled PC
12
Connecting Wireless USB VGA Adapter 16
Wireless USB VGA Display Settings 19
Wireless USB VGA Adapter in wired mode 24
Frequently Asked Questions 25
Technical Specications 26
Limited Warranty 28
Federal Communications Commission
(FCC) Statement
29
Contact 30

4
5
System Requirements
- Microsoft Windows®XP 32-bit (Service Pack 2)
- Microsoft Windows®Vista®32/64-bit
- Minimum CPU requirement: 2GHz (single core), memory: 1GB*
- Wireless USB enabled PC (embedded or via Wireless USB Host Adapter)
- USB 2.0 Compliant hardware and system
- Display with VGA port (VGA cable not included)
* In order to support 720p video, minimum system requirements CPU: 2GHz (single core), RAM: 1GB.
While playing 720p video, the system should not be doing other CPU/memory/storage consuming jobs.

4
5
Important Information
Before you get started, please NOTE:
Do not place Wireless USB devices under direct sunlight or near high heat emitting devices;
Do not place Wireless USB devices near water or wet surfaces to avoid electric hazards;
Do not place Wireless USB devices on any moving or unstable surfaces.

6
7
Package Contents
1 x Wireless USB to VGA Adapter (for Monitor/TV/Projector)
1 x USB 2.0 A to mini-B Cable (3 ft.)
1 x Velcro fabric hook-and-loop fastener
1 x Power Adapter (full range)
1 x Quick Start Guide
1 x Registration / Warranty Card
1 x Installation CD (with User Manual)

6
7
132
4 5 6 7 8
Wireless VGA Adapter
Wireless VGA Adapter
Device Overview

8
9
1. VGA : VGA Activity Indicator
LED is solid when display cable is connected
a.
LED is blinking when data is being transferredb.
2. PWR: Power Indicator
LED is solid when power is applied
a.
3. 1 – 2 – 3: Status Indicator
Single* solid light: device is wirelessly connected to
a.
the selected Wireless USB Host Adapter
Single* slowly blinking light: device is searching for
b.
a Wireless USB Host Adapter
Single* quickly blinking light: device is trying to
c.
connect to a Wireless USB Host Adapter
Rapidly scrolling lights: device is used in wired mode
d.
Three Simultaneous Blinking Lights: Cablee.
Association Mode
* Only one light at a time. The position of the light indicates
which Wireless USB Host Adapter the device is trying to
communicate with.
Wireless VGA Adapter
Wireless VGA Adapter 4. PWR plug
Power adapter socketa.
5. RESET
Association history can be erased by pressing and
a.
holding this button for 10 seconds
6. HOST
This button is used to select a different Wireless
a.
USB Host Adapter
7. USB connector
In wireless mode, this connector is used for cable
a.
association
In wired mode, this connector is used for wired
b.
operation
8. WIRED/WIRELESS switch
Choose from wired or wireless mode by using this
a.
switch

8
9
Wireless USB VGA Software Installation
Please always check www.iogear.com for latest drivers.
IMPORTANT NOTE:
If installing on Windows XP, Service Pack 2 (SP2) is required, verify that this has been installed on your PC
before installing the Wireless USB VGA Adapter software.
Before installing the GUW2015V
software, please make sure that the
Wireless USB VGA Adapter is not
connected to the computer, and the
Wireless USB VGA Adapter is not
powered.
Step 1 – Insert installation CD into drive
on your computer.
Step 2 - Select “Software Installation”
from the menu.

10
11
Step 3 – Choose installation method.
The next screen will let you choose whether you want to install the latest software from the IOGEAR
website or if you want to install the software directly from the installation CD.